Xerox Docutech 128 Install Manual
Installation Preparation Document
(for physical installation of the product only)
Xerox DocuTech 128/155/180 HighLight Color
701P46159
October 2006
The main DocuTech 128/155/180 HLC components are:
•
Sun Blade
TM
2500 Controller
•
CD/DVD combo drive
•
color flat panel monitor
•
keyboard and mouse
•
Ethernet interface (10/100/1000 BaseT)
•
Three printer interface cards
•
Controller Stand
•
Options
•
18/36 track tape drive
•
Online connection
•
QIC tape
•
USB floppy disk drive
or
•
Sun W1100Z (AMD) contoller
•
CD/DVD combo drive
•
color flat panel monitor
•
keyboard and mouse
•
Ethernet interface (10/100/1000 BaseT)
•
Three printer interface cards
•
Controller Stand
•
Options
•
18/36 track tape drive
•
Online connection
•
QIC tape
•
USB floppy disk drive
•
Solaris 10 and DocuSP print services software
•
Printer
•
Black plus one highlight color*
•
Xerographic engine with laser raster imaging system for
black and Light Emitting Diode for color
•
Permanent housing for black dry ink; customer changeable
unit (CCU) for color dry ink
•
Prints simplex or duplex
•
Inverter Feeder/Stacker and up to 3 additional
feeder/stackers
•
Optional Bypass Transport to provide connection to
additional finishers
* Additional dry inks, not listed on this document, will be customer
options as they become available, and will be offered under standard
Xerox terms and conditions.
Space Requirements / Service Space Envelope
The dimensions shown below are absolute minimums.
Configuration
Width
Depth
Min total
req’d
Width x
depth
Weight
With inverter
feeder/stacker
and one
feeder/stacker
173.3
(in)
433.3
(cm)
48.8 (in)
122
(cm)
262.5 x
131.5 (in)
631.3 x
328.8
(cm)
3164 lbs
1438 kg
With inverter
feeder/stacker
and two feeder
stackers
205.6
(in)
511.3
(cm)
48.8 (in)
122
(cm)
294.8 x
131.5 (in)
737 x
328.8
(cm)
3685 lbs
1675 kg
With inverter
feeder/stacker
and three
feeder/stackers
237.9
(in)
594.4
(cm)
48.8 (in)
122
(cm)
327.1x
131.5 (in)
817.8 x
328.8
(cm)
4206 lbs
1912 kg
Optional Bypass
Transport*
20.4 (in)
51 (cm)
28.3 (in)
71 (cm)
176
lbs
80 kg
•
The minimum total space required includes the required space
necessary for the Xerox service personnel to service the printer.
•
A minimum of 78 inches/198 cm clearance from the floor to the
nearest overhead obstruction must be maintained.
•
The printing system must be installed in a fixed location.
•
Space requirements for the controller stand are 36 x 36
inches/91 x 91 cm.
•
For proper operation, the printer must be perfectly level. On
floors less than two degrees out of level, a leveling kit must be
used to level the equipment. The printer will not function
properly on floors more than two degrees out of level.
•
For detailed space requirements and diagrams, refer to the
DocuTech 128/155/180 HighLight Color Installation Planning
Guide.
Electrical Requirements (printer)
The printer requires:
•
60 HZ service (2 cords required)
MultiSource
2-phase, dual power cord
configuration
Voltage 208/240
(4 wire)
208/240
(4 wire)
Amperage (dedicated)
50
30
Cycles
60 Hz
60 Hz
Receptacle Xerox Part No.
Receptacle NEMA Part No.
14-50R
14-30R
Receptacle Diagram
Power Cord Kit Number
Power Cord Length
15 feet
15 feet