Xerox DocuTech 180 Install Manual
Installation Preparation Document
(for physical installation of the product only)
Xerox DocuTech 180 HighLight Color
701P46151
October 2006
The main DocuTech 180 HLC components are:
•
Digital Front End Controller
•
CD/DVD combo drive
•
color flat panel monitor
•
keyboard and mouse
•
Ethernet interface (10/100/1000 BaseT)
•
Two printer interface cards
•
Controller Stand
•
Options
•
USB floppy disk drive
•
Solaris 10 and DocuSP print services software
•
Printer
•
Black plus one highlight color*
•
Xerographic engine with laser raster imaging system for
black and Light Emitting Diode for color
•
Permanent housing for black dry ink; customer changeable
unit (CCU) for color dry ink
•
Prints simplex or duplex
•
Two-tray interposer
•
In-line finishing module which includes a binder, stitcher,
and stacker
•
Optional Bypass Transport to provide connection to
additional finishers
* Additional dry inks, not listed on this document, will be customer
options as they become available, and will be offered under standard
Xerox terms and conditions.
Space Requirements / Service Space Envelope
The dimensions shown below are absolute minimums.
Configuration
Width
Depth
Min total
req’d
Width x
depth
Weight
With two tray
Interposer and
Binder/Stitcher
78 (in)
198
(cm)
42 (in)
106.6
(cm)
293.1 x
142.0 (in)
744.5 x
360.6
(cm)
3724
(lbs)
1689
(kgs)
Controller stand
36 (in)
91 (cm)
36 (in)
91 (cm)
•
The minimum total space required includes the required space
necessary for the Xerox service personnel to service the printer.
•
A minimum of 78 inches/198 cm clearance from the floor to the
nearest overhead obstruction must be maintained.
•
No obstructions, such as power poles, are allowed such that
they interfere with the Xerox Service Representative’s ability to
access the rear of the printer for service.
•
The printing system must be installed in a fixed location.
•
Space requirements for the controller stand are 36 x 36
inches/91 x 91 cm.
•
For proper operation, the printer must be perfectly level. On
floors less than two degrees out of level, a leveling kit must be
used to level the equipment. The printer will not function
properly on floors more than two degrees out of level.
•
For detailed space requirements and diagrams, refer to the
DocuTech 128/155/180 HighLight Color Installation Planning
Guide.
Electrical Requirements (printer)
The printer requires for 60 HZ service (2 cords required):
MultiSource
2-phase, dual power cord
configuration
Voltage 208/240
(4 wire)
208/240
(4 wire)
Amperage (dedicated)
50
30
Cycles
60 Hz
60 Hz
Receptacle Xerox Part No.
Receptacle NEMA Part No.
14-50R
14-30R
Receptacle Diagram
Power Cord Kit Number
Power Cord Length
15 feet
15 feet
For 50 Hz service:
•
30 amp dedicated service (WYE): 220/380 VAC or 230/400
VAC or 240/415 VAC (3 phase)
Agency certifications: UL, cUL, CE Mark, FCC
Electrical Requirements (Controller)
The Controller requires 20 AMP dedicated service. The information
for the 20 Amp electrical service is identified below.
Controller
36 Track Tape
(Optional)
Line Options
Dedicated
Dedicated
Voltage 115vac
115vac
Amperage 20
20
Cycles
60 Hz
60 Hz
Xerox Receptacle Part No.
600S3703
600S3703
Receptacle NEMA Part No.
5-20R
5-20R
Power Cord Xerox Part No.
98K19950
98K19950
Receptacle Diagram
97S02370
97S02370
Installation Considerations
1.
Dedicated electrical service is required for each component.
2.
The controller can be connected to a 15 amp or 20 amp outlet.
3.
The length of the cable from the controller to the printer is 16
feet (4.8 metres).
4.
Do not use an adapter to connect the controller to an electrical
outlet that lacks a ground connection terminal.
5.
The customer is responsible for providing the network and the
client workstation(s). The Ethernet interface on the DocuSP
controller is a auto-sensing 10/100/1000 - MB/sec twisted pair
standard (BaseT).
6.
The Ethernet connection to the DocuSP controller must be
compatible with the Institute of Electrical and Electronics
Engineers (IEEE) 802.3 standard.