- DL manuals
- Xerox
- Printer
- Phaser 200E
- Cleaning Instructions Manual
Xerox Phaser 200E Cleaning Instructions Manual
Summary of Phaser 200E
Page 1
Cleaning instructions phaser ª 200 series color printers first printing february 1995 063-1450-02.
Page 2
Copyright © 1995 by tektronix, inc., wilsonville, oregon. Printed in the united states of america. All rights reserved. Contents of this publication may not be reproduced in any form without permission of tektronix, inc. This instrument, in whole or in part, may be protected by one or more u.S. Or f...
Page 3: Users Safety Summary
Users safety summary terms in manual: caution conditions that can result in damage to the product. Warning conditions that can result in personal injury or loss of life. Power source: do not apply more than 250 volts rms between the supply conductors or between either supply conductor and ground. Us...
Page 4
Cleaning instructions iii contents introduction . . . . . . . . . . . . . . . . . . 1 thermal head . . . . . . . . . . . . . . . . . . 3 paper-feed rollers . . . . . . . . . . . . . . . . 5 paper-pick rollers . . . . . . . . . . . . . . . . 6 transfer roll sensor pad . . . . . . . . . . . . 10 drum ...
Page 5
Cleaning instructions 1 keeping your printer a top performer introduction by performing regular cleaning, you ensure that your printer produces the highest quality prints. Regular cleaning also helps prevent paper jams, smudged or streaked prints and misregistration. Cleaning the printer is easy; ju...
Page 6
2 phaser 200 series important notes about cleaning ❑ use isopropyl alcohol to clean your printer. It can be purchased at your local pharmacy. You can also use cleaning wipes that are pre-saturated with isopropyl alcohol (tektronix order number 006-7824-00). ❑ 90% isopropyl alcohol is recommended. If...
Page 7
Cleaning instructions 3 thermal head Ð clean every transfer roll change. 1 2 3 isoprop or pre-saturated isopropyl alcohol cleaning wipe ❑ turn off the printer using the switch on the side. ❑ open the top cover. ❑ open a pre-saturated cleaning wipe packet and remove the wipe or dampen a lint-free wip...
Page 8
4 phaser 200 series 4 5 on caution the thermal head may be hot. To avoid possible injury, let it cool before cleaning it. ❑ use the wipe to gently clean the entire surface of the thermal head. Cleaning in one direction only prevents dirt from being re-introduced to the thermal head. ❑ close the top ...
Page 9
Cleaning instructions 5 2 3 paper-feed rollers Ð clean every transfer roll change. 1 ❑ remove the front cover by pulling forward, using the Þngergrips at each side. ❑ clean the three paper-feed rollers; rotate them as you wipe so that all surfaces are cleaned. ❑ replace the front cover, tilting it s...
Page 10
6 phaser 200 series 2 3 a b paper-pick rollers Ð clean every transfer roll change. 1 for a4-size (metric) trays ❑ turn off the printer. ❑ remove the paper tray. Remove the paper or transparencies from the tray. If your printer has two paper trays, be sure to remove both trays. ❑ when removing paper ...
Page 11
Cleaning instructions 7 5 6 isopropyl on 4 a b ❑ turn on the printer. Wait 30 seconds until the ready light is on. ❑ open the cleaning tray. Dampen the pad on the cleaning tray with isopropyl alcohol. Dampen the entire surface but do not saturate it. ❑ slide the cleaning tray into the paper tray. Po...
Page 12
8 phaser 200 series 8 7 second feeder test switch second feeder test switch off a b 3 sec. ❑ press and hold the test switch for 3 seconds; the switch is at the back of the printer. Note when the jam light blinks you have completed cleaning this set of paper-pick rollers. ❑ if your printer has only o...
Page 13
Cleaning instructions 9 10 11 on b 9 second feeder test switch second feeder test switch 3 sec. A ❑ insert the paper tray containing the cleaning tray into the upper opening ( a ). Turn on the printer ( b ). (turning your printer off and on resets the printer default to the upper tray and lets you c...
Page 14
10 phaser 200 series transfer roll sensor pad Ð clean every 5,000 prints. 1 2 3 ❑ open the top cover. ❑ remove the transfer roll from the printer. ❑ open a pre-saturated cleaning wipe packet and remove the wipe or dampen a lint-free wipe with isopropyl alcohol. ❑ use the wipe to clean the transfer r...
Page 15
Cleaning instructions 11 3 drum Ð clean every 5,000 prints. 1 2 ❑ clean the drum. Rotate the drum as you wipe so that the entire surface is cleaned. ❑ replace the transfer roll in the printer. ❑ close the top cover..
Page 16
12 phaser 200 series exit rollers Ð clean every 5,000 prints. 1 2 3 ❑ remove the front cover. ❑ clean the exit rollers; rotate them as you wipe, so that all surfaces are cleaned. ❑ replace the front cover, tilting it slightly toward you as you align the guide-tabs in the top slot..
Page 17
February 1995 063-1450-02.