DL manuals
Xerox
Printer
Phaser 200E
Supplementary Manual

Xerox Phaser 200E Supplementary Manual

Other manuals for Phaser 200E: Cleaning Instructions Manual, Instruction Sheet

Manual is about: Xerox Phaser 200E: Install Guide

Page of 8

Download

Print this page

Bookmark us

063-1865-AA

Instruction Sheet

Phaser

200e

Phaser

200i

Phaser

220e

Upgrading a Phaser

200e, 200i or 220e printer

to a Phaser

240

This kit contains the components necessary to upgrade a Phaser 200e, 200i or 220e to a Phaser 240 Color

Printer. Generally, this involves replacing the printerÕs old image processor board with a new image

processor board. In the case of the Phaser 200e and 200i, the printerÕs engine control board must also be

replaced with a new engine control board included in this kit. In all cases, the unused or replaced

components must be returned to Tektronix. This upgrade should only be installed by qualiÞed service

personnel.

Kit contents

■

Phaser 240 image processor board

■

print engine controller board

■

8-Mbyte RAM SIMM

■

Ethernet card (Option P1)

Static electricity precautions

■

Plug in the ground adapter (003-1501-00) in an AC outlet. Connect the

anti-static mat (006-7056-00) to the adapterÕs groundplug.

■

Put on your anti-static wrist strap and connect it to the anti-static mat.

■

Leave the printer plugged into its power outlet; this preserves a

ground path for static discharges.

■

Touch the printer's bare metal frame often to discharge static

electricity from your body.

■

Handle the circuit board(s) by their edges only.

■

Do not lay the board(s) on a metal surface.

■

Avoid wearing nylon or polyester clothing; they generate static

electricity.

1 2 3 4 5 6 7 Next › »

Summary of Phaser 200E

Page 1
Copyright © 1995 by tektronix, inc.. All rights reserved. 063-1865-aa instruction sheet phaser ¨ 200e phaser ¨ 200i phaser ¨ 220e upgrading a phaser ¨ 200e, 200i or 220e printer to a phaser ¨ 240 this kit contains the components necessary to upgrade a phaser 200e, 200i or 220e to a phaser 240 color ...
Page 2: Removing The Old Boards
2 upgrading a phaser¨ 200e, 200i or 220e printer to a phaser¨ 240 removing the old boards 1. Power down the printer. Leave the power cord plugged in to provide a ground path for static discharges. Remove the interface cables. 2. Remove the top-rear and rear cabinet panels. 3. Remove the screws secur...
Page 3
3 upgrading a phaser¨ 200e, 200i or 220e printer to a phaser¨ 240 5. Remove the card cage top (3 screws). 6. Flip over the hinged card cage top. 7. Lift out the old image processor board. Flip over top lift out image processor board remove screws 31865-01.
Page 4
Note in the next step, it is only necessary to remove the old engine control board from a phaser 200e or phaser 200i color printer. 8. Disconnect the wiring harnesses leading to the engine controlÊboard. 9. Lift out the engine control board. Card cage disconnect harnesses 31865-02 lift out engine bo...
Page 5
5 upgrading a phaser¨ 200e, 200i or 220e printer to a phaser¨ 240 simm installation on the new image processor board 1. If installed, remove the font module by spreading the pawls at each end of the font module connector securing the module in place. 2. Installing the ram simm. Insert the ram simm i...
Page 6
6 upgrading a phaser¨ 200e, 200i or 220e printer to a phaser¨ 240 new image processor install 1. Slide the new image processor board into its card cage slot. 2. Close the card cage cover and secure it in place. 3. Reinstall the printer covers. Insert image processor board close card cage top.
Page 7
7 upgrading a phaser¨ 200e, 200i or 220e printer to a phaser¨ 240 4. Connect the i/o boardÕs ribbon cable to the image processor boardÕs i/o connector. Tilt the i/o board forward into place against the rear of the printerÕs card cage. Secure the i/o board in place with the two thumbscrews. 5. Reconn...
Page 8
8 upgrading a phaser¨ 200e, 200i or 220e printer to a phaser¨ 240 return the old boards to tektronix 1. Repack the old image processor and engine board (new or old) in the anti-static bags. Put the anti-static bags inside the shipping box. 2. In the u.S.A.: a. Write the printerÕs original serial num...