Copyright © 1993 by tektronix, inc.. All rights reserved. 063-1113-ah instruction sheet 4-mbyte ram simm installation — (4690f4m) finding your printer's simm installation instructions if your printer is a ... Then go to page ... Phaser px 2 phaser pxi 2 phaser ii px 6 phaser ii pxi (slide-in style i...
2 4-mbyte ram simm installation — (4690f4m) static electricity precautions ■ leave the printer plugged into its power outlet. This preserves a ground path for static discharges. ■ touch the printer's bare metal frame often to discharge static electricity from your body. ■ handle the circuit board(s)...
3 4-mbyte ram simm installation — (4690f4m) 3. Remove the emi shield. 2 1 3.
4 4-mbyte ram simm installation — (4690f4m) 4. Px image processor: locate the ram simm connector on the image processor board. It is labeled j229 (on older-version boards it is labeled j335). A. Insert the ram simm in j229 (or j335). B. Angle the ram simm into its connector; it should lock in place ...
5 4-mbyte ram simm installation — (4690f4m) note for the pxi image processor: install memory modules in the order j6 and then j7. Pxi image processor: insert a dram simm in connector j6 (or in j7 if j6 is already filled) ( a ), and tilt the module upright until it locks in place ( b ). Repeat step 4...
6 4-mbyte ram simm installation — (4690f4m) phaser ii px phaser ii pxi (slide-in style image processor board) 1. Power down the printer. Do not unplug the printer; this preserves a ground path to dissipate static charges. Disconnect the host interface cables. 2. Unscrew the four thumbscrews securing...
7 4-mbyte ram simm installation — (4690f4m) 3. Locate the simm connectors: ■ labeled j160 on the px image processor board ■ labeled j6 on the pxi image processor board 4. Px image processor: insert a memory module in connector j160 ( a ), and tilt the module upright until it locks in place ( b ). No...
8 4-mbyte ram simm installation — (4690f4m) when properly inserted, a tab on each end of the connector slips into a hole on each end of the ram simm. Also, a pawl on each end of the connector latches around each end of the ram simm to lock it in place. 5. Reinstall the image processor board in place...
9 4-mbyte ram simm installation — (4690f4m) phaser ii pxe and phaser ii pxi (bolt-down style image processor board) 1. Power down the printer. Do not unplug the printer; this preserves a ground path to dissipate static charges. Disconnect the host interface cables. 2. Remove the top panel. (lift it ...
10 4-mbyte ram simm installation — (4690f4m) 4. Remove the two screws securing the front of the emi shield. Tilt the shield up and remove it. 5. Locate the dram simm module connector j6. 6. Pxe image processor: insert the dram simm in connector j6 ( a ) and tilt the module upright until it locks in ...
11 4-mbyte ram simm installation — (4690f4m) when properly inserted, a tab on each end of the connector slips into a hole on each end of the memory module. Also, a pawl on each end of the connector latches around each end of the memory module to lock it in place. Note for the pxi image processor: in...
12 4-mbyte ram simm installation — (4690f4m) phaser iii pxi phaser 300i 1. Power down the printer. Do not unplug the printer; this preserves a ground path to dissipate static charges. Disconnect the host interface cables. 2. Remove the two screws securing the image processor board in place. Grasp un...
13 4-mbyte ram simm installation — (4690f4m) note for phaser iii printers serial numbered b01xxxx to b06xxxx: install memory modules in the order j7 and then j8. J6 should already be filled. 3. Insert a memory module in connector j7 ( a ), and tilt the module upright until it locks in place ( b ). R...
14 4-mbyte ram simm installation — (4690f4m) note for phaser iii printers serial numbered b10xxxx and higher and phaser 300i printers: install memory modules in the order j8 and then j7. J9 should already be filled. Insert a memory module in connector j8, or in j7 if j8 is filled ( a ), and tilt the...
15 4-mbyte ram simm installation — (4690f4m) phaser ii sx/dx (slide-in style image processor board) 1. Turn the printer off. Do not unplug the printer; this preserves a ground path to dissipate static charges. Disconnect the host interface cables. 2. Loosen the rear panel thumbscrews. 3. If just the...
16 4-mbyte ram simm installation — (4690f4m) 6. Insert a memory module in connector simm #1 (or in simm #2 if simm #1 is already filled) ( a ), and tilt the module upright until it locks in place ( b ). 7. Repeat step 6 to install an additional memory module. 8. Slide the 3-port multiplexer board, i...
17 4-mbyte ram simm installation — (4690f4m) phaser ii sx/dx (bolt-down style image processor board) 1. Power down the printer. Do not unplug the printer; this preserves a ground path to dissipate static charges. Disconnect the host interface cables. 2. Remove the top panel. Three of the screws secu...
18 4-mbyte ram simm installation — (4690f4m) 4. Remove the two screws securing the front of the emi shield. Tilt the shield up and remove it. 5. Locate the connectors labeled simm #1, #2, and #3 on the image processor board. (for the phaser ii dx printer, a memory module is already installed in conn...
19 4-mbyte ram simm installation — (4690f4m) 6. Insert a memory module in connector simm #1 (or in simm #2 if simm #1 is already filled) (a), and tilt the module upright until it locks in place (b). When properly inserted, a tab on each end of the connector slips into a hole on each end of the simm....
20 4-mbyte ram simm installation — (4690f4m) phaser ii sd/sdx 1. Power down the printer. Do not unplug the printer; this preserves a ground path to dissipate static charges. 2. Remove the cabinet top. (be careful lifting the cabinet top, the front panel led cable is still attached.) 3. Disconnect th...
21 4-mbyte ram simm installation — (4690f4m) 4. Remove the two screws securing the front of the emi shield. Tilt the shield up and remove it. 5. Locate the dram simm module connector j6. 6. Insert a keyed dram simm in connector j6 (or in j7 if j6 is already filled, or in j8 if j6 and j7 are already ...
22 4-mbyte ram simm installation — (4690f4m) 7. Reinstall the emi shield. Reconnect the front panel connector. Reconnect the cabinet top. 8. Turn on the printer and make a print to ensure that the printer functions correctly. 6 b a j6 a b j7 j8.
23 4-mbyte ram simm installation — (4690f4m) phaser 200i and phaser 200e 1. Power down the printer. Leave the power cord plugged in to provide a ground path for static. Remove the interface cables. 2. Remove the top-rear and rear cabinet panels. 3. Remove the screws securing the i/o board to the car...
24 4-mbyte ram simm installation — (4690f4m) 5. Remove the card cage top (3 screws). 6. Move over the hinged card cage top. 7. Lift out the image processor board. 6 7 5.
25 4-mbyte ram simm installation — (4690f4m) 8. Phaser 200e: insert a memory module in connector j6 ( a ), and tilt the module upright until it locks in place ( b ). When properly inserted, a tab on each end of the connector slips into a hole on each end of the ram simm. Also, a pawl on each end of ...
