- DL manuals
- Xerox
- Printer
- Phaser 200E
- Instruction Sheet
Xerox Phaser 200E Instruction Sheet - page 16
16
4-Mbyte RAM SIMM Installation — (4690F4M)
6.
Insert a memory module in connector SIMM #1 (or in SIMM #2 if
SIMM #1 is already filled) (
a
), and tilt the module upright until it locks
in place (
b
).
7.
Repeat Step 6 to install an additional memory module.
8.
Slide the 3-port multiplexer board, if the printer is furnished with one,
into the top slot. Slide the image processor board into the bottom slot.
Push and turn the thumbscrews to secure the board(s) in place.
9.
Reconnect the host interface cables. Turn the printer on and make a
test print to ensure that the printer prints correctly.
#1
#2
#3
6a
7
6b
31113-11
8
Summary of Phaser 200E
Page 1
Copyright © 1993 by tektronix, inc.. All rights reserved. 063-1113-ah instruction sheet 4-mbyte ram simm installation — (4690f4m) finding your printer's simm installation instructions if your printer is a ... Then go to page ... Phaser px 2 phaser pxi 2 phaser ii px 6 phaser ii pxi (slide-in style i...
Page 2: Phaser Px
2 4-mbyte ram simm installation — (4690f4m) static electricity precautions ■ leave the printer plugged into its power outlet. This preserves a ground path for static discharges. ■ touch the printer's bare metal frame often to discharge static electricity from your body. ■ handle the circuit board(s)...
Page 3
3 4-mbyte ram simm installation — (4690f4m) 3. Remove the emi shield. 2 1 3.
Page 4
4 4-mbyte ram simm installation — (4690f4m) 4. Px image processor: locate the ram simm connector on the image processor board. It is labeled j229 (on older-version boards it is labeled j335). A. Insert the ram simm in j229 (or j335). B. Angle the ram simm into its connector; it should lock in place ...
Page 5
5 4-mbyte ram simm installation — (4690f4m) note for the pxi image processor: install memory modules in the order j6 and then j7. Pxi image processor: insert a dram simm in connector j6 (or in j7 if j6 is already filled) ( a ), and tilt the module upright until it locks in place ( b ). Repeat step 4...
Page 6: Phaser II Px
6 4-mbyte ram simm installation — (4690f4m) phaser ii px phaser ii pxi (slide-in style image processor board) 1. Power down the printer. Do not unplug the printer; this preserves a ground path to dissipate static charges. Disconnect the host interface cables. 2. Unscrew the four thumbscrews securing...
Page 7
7 4-mbyte ram simm installation — (4690f4m) 3. Locate the simm connectors: ■ labeled j160 on the px image processor board ■ labeled j6 on the pxi image processor board 4. Px image processor: insert a memory module in connector j160 ( a ), and tilt the module upright until it locks in place ( b ). No...
Page 8
8 4-mbyte ram simm installation — (4690f4m) when properly inserted, a tab on each end of the connector slips into a hole on each end of the ram simm. Also, a pawl on each end of the connector latches around each end of the ram simm to lock it in place. 5. Reinstall the image processor board in place...
Page 9
9 4-mbyte ram simm installation — (4690f4m) phaser ii pxe and phaser ii pxi (bolt-down style image processor board) 1. Power down the printer. Do not unplug the printer; this preserves a ground path to dissipate static charges. Disconnect the host interface cables. 2. Remove the top panel. (lift it ...
Page 10
10 4-mbyte ram simm installation — (4690f4m) 4. Remove the two screws securing the front of the emi shield. Tilt the shield up and remove it. 5. Locate the dram simm module connector j6. 6. Pxe image processor: insert the dram simm in connector j6 ( a ) and tilt the module upright until it locks in ...
Page 11
11 4-mbyte ram simm installation — (4690f4m) when properly inserted, a tab on each end of the connector slips into a hole on each end of the memory module. Also, a pawl on each end of the connector latches around each end of the memory module to lock it in place. Note for the pxi image processor: in...
Page 12: Phaser III Pxi
12 4-mbyte ram simm installation — (4690f4m) phaser iii pxi phaser 300i 1. Power down the printer. Do not unplug the printer; this preserves a ground path to dissipate static charges. Disconnect the host interface cables. 2. Remove the two screws securing the image processor board in place. Grasp un...
Page 13
13 4-mbyte ram simm installation — (4690f4m) note for phaser iii printers serial numbered b01xxxx to b06xxxx: install memory modules in the order j7 and then j8. J6 should already be filled. 3. Insert a memory module in connector j7 ( a ), and tilt the module upright until it locks in place ( b ). R...
Page 14
14 4-mbyte ram simm installation — (4690f4m) note for phaser iii printers serial numbered b10xxxx and higher and phaser 300i printers: install memory modules in the order j8 and then j7. J9 should already be filled. Insert a memory module in connector j8, or in j7 if j8 is filled ( a ), and tilt the...
Page 15: Phaser II Sx/dx
15 4-mbyte ram simm installation — (4690f4m) phaser ii sx/dx (slide-in style image processor board) 1. Turn the printer off. Do not unplug the printer; this preserves a ground path to dissipate static charges. Disconnect the host interface cables. 2. Loosen the rear panel thumbscrews. 3. If just the...
Page 16
16 4-mbyte ram simm installation — (4690f4m) 6. Insert a memory module in connector simm #1 (or in simm #2 if simm #1 is already filled) ( a ), and tilt the module upright until it locks in place ( b ). 7. Repeat step 6 to install an additional memory module. 8. Slide the 3-port multiplexer board, i...
Page 17
17 4-mbyte ram simm installation — (4690f4m) phaser ii sx/dx (bolt-down style image processor board) 1. Power down the printer. Do not unplug the printer; this preserves a ground path to dissipate static charges. Disconnect the host interface cables. 2. Remove the top panel. Three of the screws secu...
Page 18
18 4-mbyte ram simm installation — (4690f4m) 4. Remove the two screws securing the front of the emi shield. Tilt the shield up and remove it. 5. Locate the connectors labeled simm #1, #2, and #3 on the image processor board. (for the phaser ii dx printer, a memory module is already installed in conn...
Page 19
19 4-mbyte ram simm installation — (4690f4m) 6. Insert a memory module in connector simm #1 (or in simm #2 if simm #1 is already filled) (a), and tilt the module upright until it locks in place (b). When properly inserted, a tab on each end of the connector slips into a hole on each end of the simm....
Page 20: Phaser II
20 4-mbyte ram simm installation — (4690f4m) phaser ii sd/sdx 1. Power down the printer. Do not unplug the printer; this preserves a ground path to dissipate static charges. 2. Remove the cabinet top. (be careful lifting the cabinet top, the front panel led cable is still attached.) 3. Disconnect th...
Page 21
21 4-mbyte ram simm installation — (4690f4m) 4. Remove the two screws securing the front of the emi shield. Tilt the shield up and remove it. 5. Locate the dram simm module connector j6. 6. Insert a keyed dram simm in connector j6 (or in j7 if j6 is already filled, or in j8 if j6 and j7 are already ...
Page 22
22 4-mbyte ram simm installation — (4690f4m) 7. Reinstall the emi shield. Reconnect the front panel connector. Reconnect the cabinet top. 8. Turn on the printer and make a print to ensure that the printer functions correctly. 6 b a j6 a b j7 j8.
Page 23: Phaser 200I and Phaser 200E
23 4-mbyte ram simm installation — (4690f4m) phaser 200i and phaser 200e 1. Power down the printer. Leave the power cord plugged in to provide a ground path for static. Remove the interface cables. 2. Remove the top-rear and rear cabinet panels. 3. Remove the screws securing the i/o board to the car...
Page 24
24 4-mbyte ram simm installation — (4690f4m) 5. Remove the card cage top (3 screws). 6. Move over the hinged card cage top. 7. Lift out the image processor board. 6 7 5.
Page 25
25 4-mbyte ram simm installation — (4690f4m) 8. Phaser 200e: insert a memory module in connector j6 ( a ), and tilt the module upright until it locks in place ( b ). When properly inserted, a tab on each end of the connector slips into a hole on each end of the ram simm. Also, a pawl on each end of ...