1. DL manuals
  2. Xpr
  3. Card Reader
  4. B100PROX-MF-SA
  5. User Manual

Xpr B100PROX-MF-SA User Manual

Manual is about: Standalone Biometric Mifare Reader

Summary of B100PROX-MF-SA

  • Page 1

    Relay1 time (for relay 1 in b100prox-mf-sa,ru2, rtt and dinrtt ) swipe the master/admin finger 8 times select relay open time 1 sec 3 sec 5 sec 10 sec 20 sec 30 sec 60 sec toggle scroll down to select: ok beep back to main menu blinking row > bl bl bl bl bl bl bl bl relay2 time (for relay 2 in , din...

  • Page 2

    1.0 description 2.0 mounting 3.0 specifications 4.0 a d pplication iagram 5.0 wiring 6.0 r s t ecommended wiping echnique 6.1 tapping the sensor 6.2 scrolling the sensor up and down 7.0 indication 8.0 q p uick rogramming 8.1 adding master finger and delete all users 8.2 add user in group 1 8.3 add u...

  • Page 3

    Note: swipe upwards to exit the menu example: task: set the reader to work in “finger and card” mode scroll master finger 10 mes, tap, scroll twice, tap, scroll 4 mes, tap, swipe up to exit. Ok beep entry mode back to main menu scroll down to select: finger finger or pin finger and pin finger or car...

  • Page 4

    Dinrtt (optional) 2 relay remote unit and request-to-exit button b100prox-mf-sa standalone biometric reader or rtt (optional) 1 relay remote unit and request-to-exit button secur ed ar ea outside r 485 (max. 50m) s fingerprint capacity: prox. Cards capacity: card type: output: push button input: doo...

  • Page 5

    Select admin nr. Admin 1 admin 2 scroll down to select: bl bl bl ok beep deleting.. Back to main menu swipe the master/admin finger unl 13 mes the light pa ern on figure.11 is shown figure.11 tap sensor tap sensor x 13 - there is 1 master finger. The master finger can enroll/delete user and all the oth...

  • Page 6

    4 x tricolor programming leds (red, green, orange) tricolor status led green - access granted red - access denied orange - idle mode ok beep - short + long beep - 3 short beeps error beep swipe again - 2 short beeps follow the below instructions for correct finger swiping starting from the first fin...

  • Page 7

    Select user group to delete swipe the finger to select: ok beep group 1 group 2 group 3 group 4 group 5 group 6 group 7 group 8 bl bl bl bl bl bl bl bl back to main menu swipe the master/admin finger unl 6 mes the light pa ern on figure.13 is shown figure.13 tap sensor x 6 tap sensor note: all fingers ...

  • Page 8

    1. Swipe the master or admin finger twice (present the card) - optional 2. Swipe the user finger min. 6 times (until ok beep) 1. Swipe the master or admin finger , 3 times 2. Wait 6 seconds for the light pattern on fig.4 3. Swipe the master or admin finger once more figure.1 figure.2 6 sec. 6 sec. 1...

  • Page 9

    Select user group (orange blinking) group 1 group 2 group 3 group 4 group 5 group 6 group 7 group 8 assign relay output relay 1 relay 2 both none swipe the finger to select: swipe the finger to select: bl bl bl bl bl bl bl bl bl bl bl bl bl bl swipe the master/admin finger unl 5 mes the light pa ern ...

  • Page 10

    B (rs485) a (rs485) 1. Close the jumper. Dinrtt beeps continuously and the red led blinks. 2. Open the jumper 3. Wait for beep + ok beep (short + short + long beep) after the ok beep, the coupling is done. P 2 b gnd p 1 b gnd n1 c com n1 o n2 c com n2 o a b tamp tamp r 485 s gnd +12v gnd +12v exit b...