Xpr B100PROX-MF-SA User Manual - page 10
B
(RS485)
A
(RS485)
1. Close the Jumper. DINRTT beeps
continuously and the red led blinks.
2. Open the Jumper
3. Wait for Beep + OK Beep (short + short +
long beep)
After the OK beep, the coupling is done.
P
2
B
GND
P
1
B
GND
N1
C
COM
N1
O
N2
C
COM
N2
O
A
B
TAMP
TAMP
R
485
S
GND
+12V
GND
+12V
Exit Button
(NO)
1N400
7
+
-
12 VDC
+
-
DINRTT
+12V
+12V
GND
GND
GND
P
1
B
N1
O
COM
1
2
1. Put Dipswitch No.1 to position ON. RTT beeps continuously and the red led blinks.
2. Put Dipswitch No.1 to position OFF.
3. Wait for Beep + OK Beep (short + short + long beep)
After the OK beep, the coupling is done.
1 2
ON
If secure installation is needed, the reader can be connected to remote relay unit at secured area, which
also plays the role of request-to-exit push button. Follow the instructions bellow to pair(couple) both
devices or refer to the Remote Relay’s Manual.
User Finger x 2
Swipe ANY enrolled finger twice (within 7 seconds) and the Door will stay unlocked, until valid finger is swiped.
While the door is unlocked the tricolor status LED stays green.
To use this feature, enable the same from the menu.(page 16). It applies for product version 1.0.2.0.0 and above.
Note: Make sure that the door lock can withstand activation in longer periods.
12 VDC
+
-
1N400
7
+
-
RTT
Black
Red
Pink
Violet
Black
Brown
Pink
Violet
Red
White
Yellow
COM
NO
GND
12V out
A
(RS485)
B
(RS485)
B100PROX-MF-SA
Black
Red
Pink
Violet
B
R
485
S
12 VDC
+
-
NOTE: This combination protects the gate from a possible tampering.
The door opening is controlled by the internal device (
). Resetting B100 will delete the pairing with
.
R 2
R 2
U
U
The pairing is only done from the remote relay unit (RU2).
10
9.0 P
- B
EA
R
R
U
AIRING
IOMETRIC R
DER AND EMOTE ELAY
NIT
10.0 K
D
U
EEP THE
OOR
NLOCKED
9.1 Pairing B100PROX-MF-SA with DINRTT
9.2 Pairing B100PROX-MF-SA with RTT
Select User Group
(Orange Blinking)
Group 1
Group 2
Group 3
Group 4
Group 5
Group 6
Group 7
Group 8
Assign Relay Output
Relay 1
Relay 2
Both
None
Swipe the finger to select:
Swipe the finger to select:
BL
BL
BL
BL
BL
BL
BL
BL
BL
BL
BL
BL
BL
BL
Swipe the Master/Admin finger
unl
5 mes
the light pa ern on figure.9 is shown
Figure.9
Swipe the user finger for
mode
Finger
min.6 mes.
When using proximity reader for
Mode, first present the Card then
Finger Or/and Card
swipe the finger min.
.
6 mes
x 5
NOTE:
Swipe UPWARDS
to exit the MENU
Example:
Task: Add a user in Group2, that will acvate Relay1.
Scroll Master Finger 5 mes, tap, scroll ones, tap, tap, swipe user finger 6 mes, swipe UP to exit.
Tap sensor
11
11.0 B100PROX-MF-SA P
M
ROGRAMMING
ENU
11.1 Adding Users
Tap sensor
Tap sensor