13 12 2200 nw 32nd st. Pompano beach, fl 33069 toll free (800) 659-5843 • fax (954) 933-3473 x t r e m e • p o l i s h i n g • s y s t e m s product code * concgenie 3 i n 1 • g r i n d e r • e d g e r • polisher f l o o r • g r i n d i n g • m a c h i n e c o n c r e t e g e n i e.
1 1.
1 this book has important information for use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your concrete genie could result in injury to you or other personnel, damage to the machine or to other property could ...
3 2 danger means: severe bodily or death can occur to you or other personnel if the danger statements found on this machine or in this owner’s manual are ignored or are not adhered to. Read and observe all danger statements found in this owner’s manual and on your machine. Warning means: injury can ...
3 parameter description function, scope original data e-01 control way 0. Keyboard control 1. Terminal control 2. Rs485 com port control 0 e-02 frequency given selection 0. Keyboard number setting 1. Keyboard potentiometer 2. Voltage signal or terminal vs1 1 e-13 speedup time 0.1-6500.0 second 30 e-...
5 4 fault code fault type possible fault reason troubleshooting s.C. System fault 1. Acceleration time is set too short 2. Frequency inverter output phase of grounding short circuit 3. Module failure 4. Disturbance 1. Lengthen acceleration time 2. Check the peripheral device, reset after troubleshoo...
5 xtreme hard densifier number 1 brand for hardening, protecting & cleaning concrete floors xtreme hard is a highly reactive colloidal silica-based densifying agent. The colloidal silica molecule has more reactive sites, so it goes to work quickly, within 1-2 minutes. Spray it on the concrete until ...
7 6 parameter input resetting 1. Unlock press prg, no. 00000 showing , then press set, change the number to 12345 (from left to right), then press set again, po will show on screen. 2. Restore factory settings press set, p0.00 showing, change it to p0.17, press set, change the number to 1, then pres...
7 recessed indicator lights reset button emergency stop button on ~ off switch on (left) ~ tools spin counter clock wise * important when running pcds, check cor- rect rotation for each type of pcd * note if computer error is indicated on panel, press reset button only! This resets computer to origi...
9 8 *up-grated ~ xps magnetic plates installed do not accept imitations: use only genuine xps magnetic plates xtreme diamond polishing pads xtreme resin pads xtreme ceramic pads metal bond diamonds - 6 seg metal bond diamonds - 8 seg metal bond diamonds - 10 seg pcd diamond traps for best results us...
9 adjust the handle position (for 2t series) 1. Pull handle adjuster as picture (8), adjust handle to suitable position and release handle adjuster, the handle will be locked up as picture (9) 2. Grip handle to operate machine water controller 1. Ensure water controller is off before water injection...
11 10 specification may be amended without notice • description..................................................Concrete genie (2t-2) • voltage............................................................220v - 1ph • working width..........................................560mm - 22 inch • sweep........
11 troubleshooting swirls on the floor after grinding • moving the machine too fast or machine stay still too long • adopt inappropriate pad scratch on the floor • machine standing still while the pad is running • grinding method is not correct • adopt inappropriate pad • incorrect operation machine...
13 an american grinder company x t r e m e • p o l i s h i n g • s y s t e m s www.Facebook.Com/xtremepolishingsystems www.Youtube.Com/user/xtremepolishing info@xtremepolishingsystems.Com 2 2 0 0 n w 3 2 n d s t . # 7 0 0 p o m p a n o b e a c h , f l 3 3 0 6 9 ( 8 6 6 ) 81 2-9 3 1 9 www.Xtremepolis...
