1. DL manuals
  2. Yamaha
  3. Outboard Motor
  4. 8C
  5. Owner's Manual

Yamaha 8C Owner's Manual

Summary of 8C

  • Page 1

    8c owner’s manual u.S.A.Edition lit-18626-05-30 6m8-f9-17 hyoushi 1/7/03 14:12 page 1.

  • Page 2

    6m8-f9-17 hyoushi 1/7/03 14:12 page 2.

  • Page 3: To The Owner

    E thank you for choosing a yamaha out- board motor. This owner’s manual con- tains information needed for proper oper- ation, maintenance and care. A thorough understanding of these simple instruc- tions will help you obtain maximum enjoyment from your new yamaha. If you have any question about the ...

  • Page 4: General Information

    E general information basic components operation maintenance trouble recovery index read this owner’s manual carefully before operating your outboard motor. 1 2 3 4 5 6 ema20010 contents 6m8-f9-17-1 2/4/03 9:55 am page 3.

  • Page 5: Chapter 1

    Emb00010 chapter 1 general information identification numbers record ....................................................1-1 emission control information ...1-2 safety information ..........................1-3 important labels ..............................1-5 basic boating rules ......................

  • Page 6: Identification Numbers

    1-1 e 1 401012 emu00005 identification numbers record emu00007 outboard motor serial num- ber the outboard motor serial number is stamped on the label attached to the port side of the clamp-bracket. Record your outboard motor serial num- ber in the spaces provided to assist you in ordering spare par...

  • Page 7: Emission Control

    1-2 e q w emu01385 emission control information emu01386 north american models this engine conforms to u.S. Environmental protection agency (epa) regulations for marine si engines. See the label affixed to your engine for details. Approval label of emission control certificate this label is attached...

  • Page 8: Safety

    1-3 e emu00917 safety information 8 before mounting or operating the out- board motor, read this entire manual. Reading it should give you an under- standing of the motor and its operation. 8 before operating the boat, read any owner’s or operator’s manuals supplied with it and all labels. Be sure y...

  • Page 9

    1-4 e 8 be informed about boating safety. Additional publications and information can be obtained from many organiza- tions, including the following: united states coast guard consumer affairs staff (g-bc) office of boating, public, and consumer affairs u.S. Coast guard headquarters washington, d.C....

  • Page 10: Important Labels

    1-5 e 001733 q w emb30010 important labels warning labels 1 2 warning this engine is equipped with a neutral starting device. The engine will not start unless the shift control is in neutral position. 6e0-83627-41 warning 6 be sure shift control is in neutral before starting engine. (except 2hp) 6 d...

  • Page 11: Basic Boating Rules

    1-6 e emb40010 basic boating rules (rules of the road) just as there are rules which apply when you are driving on streets and high ways, there are waterway rules which apply when you are driving your boat. These rules are used internationally, and are also enforced by the united states coast guard ...

  • Page 12: Rules When Encountering

    1-7 e rules when encountering vessels there are three main situations which you may encounter with other vessels which could lead to a collision unless the steering rules are followed: meeting (you are approaching another vessel head-on) crossing (you are travelling across the other vessel’s path) o...

  • Page 13

    1-8 e its course and speed. You must stay out of its way until you are clear of it. Likewise, if another vessel is passing you, you should maintain your speed and direction so that the other vessel can steer itself around you. Other special situations there are three other rules you should be aware ...

  • Page 14

    1-9 e remember, markings may vary by geo- graphic location. Always consult local boating authorities before driving your boat in unfamiliar waters. 1 1 a 1 1 proceeding toward head of navigation from seaward can buoy odd number. Leave to port. Or secondary channel buoys starts new numbering system o...

  • Page 15: Fueling Instructions

    1-10 e emu00016 fueling instructions w gasoline and its vapors are high- ly flammable and explosive! 8 do not smoke when refueling, and keep away from sparks, flames, or other sources of ignition. 8 stop engine before refueling. 8 refuel in a well-ventilated area. Refuel portable fuel tanks off the ...

  • Page 16: Gasoline (Petrol)

    1-11 e emu00018 gasoline (petrol) if knocking or pinging occurs, use a differ- ent brand of gasoline or premium unlead- ed fuel. If unleaded gasoline is not avail- able, then leaded regular gasoline can be used. Emu00027 gasohol there are two types of gasohol: gasohol containing ethanol and that con...

  • Page 17: Propeller Selection

    1-12 e emu01395 propeller selection the performance of your outboard motor will be critically affected by your choice of propeller, as an incorrect choice could adversely affect performance and could also seriously damage the motor. Engine speed depends on the propeller size and boat load. If engine...

  • Page 18: Start-In-Gear Protection

    1-13 e 1 propeller diameter (in inches) 2 propeller pitch (in inches) 3 type of propeller (propeller mark) refer to the section “checking pro- peller” for instructions on propeller removal and installation. Emu01209 start-in-gear protection yamaha outboard motors or yamaha approved remote control un...

  • Page 19: Chapter 2

    Emc00010 chapter 2 basic components main components ..............................2-1 operations of controls and other functions ................................2-2 fuel tank.................................................2-2 gear shift lever ......................................2-2 engine stop bu...

  • Page 20: Main Components

    2-1 e emu01206 main components q w e r t y u !5 !6 i o !0 !1 !2 !3 !4 1 recoil starter handle 2 choke knob 3 throttle control grip 4 throttle friction adjustment 5 engine stop button/ engine stop lanyard switch 6 clamp screw 7 rope attachment 8 cooling water inlet 9 anti-cavitation plate 0 trim angl...

  • Page 21: Operations of Controls

    2-2 e 902065 q w e r 310011 q w e emc20010 operations of controls and other functions emc21012 fuel tank if your model was equipped with a portable fuel tank, its function is as fol- lows. 1 fuel hose joint 2 fuel meter(if equipped) 3 fuel tank cap 4 air vent screw(if equipped) fuel hose joint this ...

  • Page 22: Control Model)

    2-3 e 308041 w q emc27011 engine stop button (for tiller control model) pushing this button opens the ignition cir- cuit and stops the engine. Emu00931 engine stop lanyard switch (for tiller control model) the lock-plate 1 must be attached to the engine stop lanyard switch for the engine to run. The...

  • Page 23: Recoil Starter Handle

    2-4 e 503013 q 305014 209015 emc44010 recoil starter handle (if equipped) pull the handle gently until resistance is felt. Then vigorously pull the handle straight out to crank the engine to start it. Emc40010 throttle control grip (for tiller control model) the throttle control grip is on the tille...

  • Page 24: Tiller Handle

    2-5 e emc60010 tiller handle (for tiller control model) moving the tiller handle sideways to adjust the steering direction. 503015 502022 emc64010 throttle friction adjustment (for tiller control model) a friction device in the tiller handle pro- vides resistance to movement of the throttle grip. Th...

  • Page 25: Steering Friction Adjustment

    2-6 e 408011 404032* emd00010 steering friction adjustment (for tiller control model) a friction device provides resistance to steering movement. This is adjustable for operator preference. An adjusting screw/bolt is located on the swivel bracket. To increase the resistance: turn the adjusting screw...

  • Page 26: Shallow Water Lever

    2-7 e 403022 301036* q emd08110 shallow water lever (if equipped) pushing this lever down will tilt the motor up partially to provide more clearance when operating in shallow water. Emd62011 top cowling lock lever to remove the engine top cowling, turn the lock lever. Then lift off the cowling. When...

  • Page 27: Chapter 3

    Emf00010 chapter 3 operation installation ........................................3-1 mounting the outboard motor ............3-2 clamping the outboard motor.............3-4 filling fuel and engine oil ............3-5 filling fuel ..............................................3-5 gasoline (petrol) a...

  • Page 28: Installation

    3-1 e emf10010 installation c c incorrect engine height or obstructions to smooth water flow (such as the design or condition of the boat or acce- ssories such as transom ladders/depth finder transducers) can create airborne water spray while the boat is cruising. Severe engine damage may result if ...

  • Page 29: Mounting The Outboard

    3-2 e 104011 q emu00176 mounting the outboard motor w improper mounting of the outboard motor could result in hazardous condi- tions such as poor handling, loss of con- trol, or fire hazards. Observe the follow- ing: 8 the information presented in this sec- tion is intended as reference only. It is ...

  • Page 30

    3-3 e 104013 0~25mm (0~1in.) w overpowering a boat may cause severe instability. Do not install an outboard motor with more horsepower than the maximum rating on the capacity plate of the boat. If the boat does not have a capacity plate, consult the boat manufac- turer. Emu01298 mounting height to r...

  • Page 31: Clamping The Outboard

    3-4 e 409011 410012 emf14010 clamping the outboard motor 1) place the outboard on the transom so that it is positioned as close to the center as possible. Tighten the tran- som clamp screws evenly and secure- ly. Check the clamp-screws for tight- ness occasionally during operation of the motor as th...

  • Page 32: Filling Fuel

    3-5 e filling fuel and engine oil emf30010 filling fuel 1) remove the fuel tank cap. 2) fill the fuel tank carefully. 3) close the cap securely after refueling. Wipe up any spilled fuel. Ring free fuel additive gasoline is a precise blend of many differ- ent substances, each chosen to give cer- tain...

  • Page 33: Gasoline (Petrol) and Oil

    3-6 e emf35010* gasoline (petrol) and oil mixing pre-mix model 1) pour oil and gasoline into the fuel tank, in that order. 1 oil 2 gasoline (petrol) 2) then mix the fuel thoroughly by shak- ing. 3) make sure the oil is mixed with gaso- line. C c 8 avoid using any oil other than the des- ignated type...

  • Page 34: Pre-Operation Checks

    Note: if using a permanently installed tank, pour the oil gradually as the fuel is being added to the tank. 3-7 e mixing ratio 100 : 1 gasoline (petrol) engine oil 1 l (0.26 us gal, 0.22 imp gal) 12 l (3.2 us gal, 2.6 imp gal) 14 l (3.7 us gal, 3.1 imp gal) 24 l (6.3 us gal, 5.3 imp gal) 0.01 l (0.0...

  • Page 35: Breaking In (Running In)

    3-8 e emf43010 controls 8 check throttle, shift, and steering for proper operation before starting the engine. 8 the controls should work smoothly, without binding or unusual free play. 8 look for loose or damaged connec- tions. 8 check operation of the starter and stop switches when the outboard mo...

  • Page 36

    3-9 e emu00226 run the engine under load (in gear with a propeller installed) as follows. 1) first 10 minutes: run the engine at the lowest possi- ble-speed. A fast idle in neutral is best. 2) next 50 minutes: do not exceed half throttle (approxi- mately 3,000 r/min). Vary engine speed occasionally....

  • Page 37: Starting Engine

    3-10 e 902073 304014* 001671 902072 e f emu01147 starting engine w 8 before starting the engine, make sure that the boat is tightly moored and that you can steer clear of any obstructions. Be sure there are no swimmers in the water near you. 8 when the air vent screw is loosened, gasoline (petrol) v...

  • Page 38: Procedure For Tiller Control

    3-11 e emu14970 procedure for tiller control model 4) place the gear-shift lever in the neu- tral position. Note: the start-in-gear protection device pre- vents the engine from starting except when in neutral. 001367 310012 n 5) attach the engine stop switch lanyard to a secure place on your clothin...

  • Page 39

    3-12 e emu00240 manual start model 7) pull out the choke knob completely. After the engine starts, return the knob to the original position. Note: 8 it is not necessary to use the choke when restarting a warm engine. 8 if the choke knob is left pulled out after the engine starts, the engine will sta...

  • Page 40: Warming Up Engine

    3-13 e emg00010-* warming up engine 1) before beginning operation, allow the engine to warm up at idling speed for 3 minutes. (failure to do this will shorten engine life.) 2) check for a steady flow of water from the cooling-water pilot hole. C c a continuous flow of water from the pilot hole shows...

  • Page 41: Shifting

    3-14 e n f 310013 503012 310014 r n emg20111 shifting w before shifting, make sure there are no swimmers or obstacles in the water near you. C c to change the shifting position from for- ward to reverse or vice-versa, close the throttle first so that the engine idles (or runs at low speeds). Emg2211...

  • Page 42: Stopping Engine

    3-15 e 304014* 902071 e f emg38010 stopping engine let it cool off for a few minutes at idle or low speed first. Stopping the engine immediately after operating at high speed is not recommended. Emu00275 1) push and hold the engine stop button until the engine comes to a complete stop. 2) after stop...

  • Page 43: Trimming Outboard

    3-16 e 105024* q emu01412 trimming outboard motor the trim angle of the outboard motor helps determine the position of the bow of the boat in the water. The correct trim angle will help improve performance and fuel economy while reducing strain on the engine. The correct trim angle depends upon the ...

  • Page 44: Adjusting Trim Angle

    3-17 e 404032* q emu00951 manual tilt model there are 4 or 5 holes provided in the clamp bracket to adjust the outboard motor trim angle. 1) stop the engine. 2) remove the trim angle adjusting rod 1 from the clamp bracket while tilting the motor up slightly. 3) reposition the rod in the desired hole...

  • Page 45

    3-18 e 001672 q 001673 w 001674 e emu19160 trim angle settings and boat handling when the boat is on plane, a bow-up atti- tude results in less drag, greater stability and efficiency. This is generally when the keel line of the boat is up about 3 to 5 degrees. With the bow up, the boat may have a gr...

  • Page 46: Cruising In Shallow

    3-19 e emg70011 cruising in shallow water the outboard motor can be tilted up par- tially to allow operation in shallow water. W 8 place the gear shift in the neutral posi- tion before using the shallow water cruising system. 8 run the boat at the lowest possible speed when using the shallow water c...

  • Page 47: Procedure

    3-20 e 310012 n 412011* 3) the shallow water lever will lock, sup- porting the engine in a partially raised position. 4) when lowering the engine, slightly tilt up the engine and push the shallow water lever down. Then, slowly lower the engine to the normal position. 2) slightly tilt up the engine. ...

  • Page 48: Tilting Up/down

    3-21 e 105031 emh10110 tilting up/down if the engine will be stopped for some time, or if the boat is moored in shallows, the engine should be tilted up to protect the propeller and casing from damage by collision with obstructions, and also to reduce salt corrosion. C c 8 before tilting the motor, ...

  • Page 49: Procedure For Tilting Up

    3-22 e 304014* emu00288 procedure for tilting up 1) place the gear shift lever in neutral. 310012 n 2) remove the fuel line connection from the motor. 3) hold the rear of the top cowling with one hand and fully tilt the engine up. 4) push the tilt support knob into the clamp bracket. Procedure for t...

  • Page 50: Cruising In Other

    3-23 e emh60010 cruising in other conditions cruising in salt water after operating in salt water, wash out the cooling-water passages with fresh water to prevent them from becoming clogged- up with salt deposits. Note: refer to cooling system flushing instruc- tions in “transporting and storing out...

  • Page 51: Chapter 4

    Emk00010 chapter 4 maintenance specifications .....................................4-1 transporting and storing outboard motor ...............................4-2 trailering outboard motor ...................4-2 storing outboard motor .......................4-3 periodic maintenance .....................

  • Page 52: Specifications

    4-1 e emu01693*¯ specifications model unit 8mh item dimensions overall length mm (in.) overall width mm (in.) overall height s mm (in.) transom height s mm (in.) weight s kg (lb.) performance full throttle operating range r/min maximum output kw (hp) @ r/min idling speed (in neutral) r/min engine ty...

  • Page 53: Transporting and

    4-2 e 102015 q emu01369 transporting and storing outboard motor w leaking fuel is a fire hazard. When trans- porting and storing the outboard motor, close the air vent screw and fuel cock to prevent fuel from leaking. Emu00326 trailering outboard motor the motor should be trailered and stored in the...

  • Page 54

    4-3 e emk22010** storing outboard motor when storing your yamaha outboard for prolonged periods of time, (2 months or longer), several important procedures must be performed to prevent expensive damage. It is advisable to have your outboard ser- viced by an authorized yamaha dealer prior to storage....

  • Page 55

    4-4 e 605011 q w emu00338 flushing cooling system and fogging engine cooling system flushing is essential to prevent the cooling system from clogging up with salt, sand, or dirt. In addition, fog- ging of the engine is mandatory to pre- vent expensive engine damage due to rust. Perform the flushing ...

  • Page 56

    4-5 e emk26010 lubrication 1) remove the spark plugs, and spray a 10 second spray of yamaha stor-rite engine fogging oil into each cylinder. Grease the spark plug threads and reinstall the spark plugs and torque to proper specification. (refer to the periodic maintenance section, “cleanning and adju...

  • Page 57: Periodic Maintenance

    4-6 e emu01569 periodic maintenance w be sure to turn off the engine when you perform maintenance unless otherwise specified. If the owner is not familiar with machine servicing, this work should be done by a yamaha dealer or other quali- fied mechanic. Maintenance, replacement, or repair of the emi...

  • Page 58: Maintenance Chart

    4-7 e emu19270 maintenance chart frequency of maintenance operations may be adjusted according to the operating condi- tions, but the following table gives general guidelines. Refer to the sections in this chapter for explanations of each owner-specific action. The mark ( ● ) indicates the check-ups...

  • Page 59: Cleaning and Adjusting Spark

    Emu01202 cleaning and adjusting spark plug w when removing or installing a spark plug, be careful not to damage the insulator. A damaged insulator could allow external sparks, which could lead to explosion or fire. The spark plug is an important engine component and is easy to inspect. The condition...

  • Page 60

    When fitting the plug, always clean the gasket surface and use a new gasket. Wipe off any dirt from the threads and screw in the spark plug to the correct torque. Note: if a torque-wrench is not available when you are fitting a spark plug, a good esti- mate of the correct torque is 1/4 to 1/2 a turn...

  • Page 61: Checking Fuel System

    4-10 e emk38010 checking fuel system w gasoline (petrol) and its vapors are highly flammable and explosive. Keep away from sparks, cigarettes, flames or other sources of ignition. Check the fuel line for leaks, cracks, or malfunctions. If any problem is found, it should be repaired immediately by ya...

  • Page 62: Filter

    4-11 e 207015* emm52010 inspecting and replacing fuel filter w gasoline (petrol) is highly flammable, and its vapors are flammable and explosive. 8 if you have any question about properly doing the procedure, consult your yamaha dealer. 8 do not perform the procedure on a hot or running engine. Allo...

  • Page 63: Inspecting Idling Speed

    4-12 e emu09912 inspecting idling speed w 8 do not touch or remove electrical parts when starting or during operation. 8 keep hands, hair and clothes away from flywheel and other rotating parts while engine is running. C c this procedure must be performed while the outboard motor is in the water. A ...

  • Page 64: Exhaust Leakage

    4-13 e 606011 exhaust leakage start the engine and check that no exhaust leaks from the joints between the exhaust cover, cylinder head and crank case. Water leakage start the engine and check that no water leaks from the joints between the exhaust cover, cylinder head and crank case. Emk78010 check...

  • Page 65: Greasing

    4-14 e emu00366 greasing yamaha marine grease (water resistant grease) 103101 6m8-f9-17-4 2/4/03 9:50 am page 15.

  • Page 66: Checking Propeller

    4-15 e 210012 602051 602054 emu00388 checking propeller w you could be seriously injured if the engine accidentally starts while you are near the propeller. 8 before inspecting, removing or installing the propeller, remove the spark plug caps from the spark plugs. Also, put the shift control in neut...

  • Page 67

    4-16 e 602052 000607 r e w q t emu00977 removing the propeller 1) straighten the cotter-pin 1 and pull it out using a pair of pliers. 2) remove the propeller nut 2 and washer 3 . 3) remove the propeller 4 and thrust washer 5 . 6m8-f9-17-4 2/4/03 9:50 am page 17.

  • Page 68

    4-17 e 602053 emu00396 installing the propeller c c 8 be sure to install the thrust washer before installing the propeller, other- wise the lower case and propeller boss may be damaged. 8 be sure to use a new cotter pin and bend the ends over securely. Otherwise the propeller could come off during o...

  • Page 69: Changing Gear Oil

    4-18 e 102015 001418 w q emu01460¯ changing gear oil w 8 be sure the outboard is securely fas- tened to the transom or a stable stand. You could be severely injured if the out- board falls on you. 8 never get under the lower unit while it is tilted, even when the tilt-support lever/knob is locked. S...

  • Page 70: Cleaning Fuel Tank

    4-19 e 5) with the outboard motor in a vertical position, and using a flexible or pres- surized filling device, inject the gear oil into the oil drain plug hole. 6) when the oil begins to flow out of the oil level plug hole, insert and tighten the oil level plug. 7) insert and tighten the oil drain ...

  • Page 71: Inspecting and Replacing

    4-20 e 902066 604013 emu14622 inspecting and replacing anode(s) yamaha outboard motors are protected from corrosion by sacrificial anodes. Inspect the external anodes periodically. Remove scales from the surfaces of the anodes. Consult a yamaha dealer for replacement of external anodes. C c do not p...

  • Page 72: Checking Bolts and Nuts

    4-21 e eml40010 checking bolts and nuts 1) check that bolts securing the cylinder head and engine and the nut securing the flywheel are tightened with their specified tightening torques. 2) check the tightening torques of other bolts and nuts. 102031 102025 eml44010 coating the boat bottom a clean h...

  • Page 73: Chapter 5

    Emn00010 chapter 5 trouble recovery troubleshooting ..............................5-1 temporary action in emergency ............................................5-5 impact damege .....................................5-5 starter will not operate.........................5-6 treatment of submerged motor...

  • Page 74: Troubleshooting

    5-1 e emu01663¯ troubleshooting a problem in the fuel, compression, or ignition systems can cause poor starting, loss of power, or other problems. The troubleshooting chart describes basic checks and possi- ble remedies. (this chart covers all yamaha outboard motors. Therefore, some items may not ap...

  • Page 75

    5-2 e c. Engine idles irregularly or stalls. Trouble possible cause remedy 1. Spark plug(s) fouled or incorrect type. 2. Fuel system obstructed. 3. Fuel contaminated or stale. 4. Fuel filter clogged. 5. Failed ignition parts. 6. Spark plug gap incorrect. 7. Poor connections or damaged ignition wirin...

  • Page 76

    5-3 e trouble possible cause remedy 1. Propeller damaged. 2. Propeller pitch or diameter incorrect. 3. Trim angle incorrect. 4. Motor mounted at incorrect height on transom. 5. Boat bottom fouled with marine growth. 6. Spark plug(s) fouled or incorrect type. 7. Weeds or other foreign matter tangled ...

  • Page 77

    5-4 e trouble possible cause remedy e. Engine vibrates excessively. 1. Propeller damaged. 2. Propeller shaft damaged. 3. Weeds or other foreign matter tangled on propeller. 4. Motor mounting bolt loose. 5. Steering pivot loose or damaged. 1. Have propeller repaired or replaced. 2. Have serviced by a...

  • Page 78: Temporary Action In

    5-5 e 607011 emn20010 temporary action in emergency emh80010 impact damage w the outboard motor can be seriously damaged by a collision while operating or trailering. Damage could make the out- board motor unsafe to operate. If the outboard motor hits any object in the water, follow the procedure be...

  • Page 79: Starter Will Not Operate

    5-6 e emn30110 starter will not operate if the starter mechanism does not operate (engine cannot be cranked with the starter), the engine can be started with an emergency starter rope. W 8 use this procedure only in an emer- gency and only to return to port for repairs. 8 when the emergency starter ...

  • Page 80

    5-7 e 208014 emr00001 4) to start the engine with emergency starter rope, insert the knotted end of the rope into the notch in the flywheel rotor and wind the rope several turns clockwise. Then, give a strong pull straight out to crank the engine. Repeat if necessary. Procedure 1) remove the top cow...

  • Page 81: Treatment of Submerged

    5-8 e 107012 107013 107014 emn50011 treatment of submerged motor if the outboard motor is submerged, immediately take it a yamaha dealer. Otherwise, some corrosion may begin almost immediately. If you cannot imme- diately take the outboard motor to a yamaha dealer, follow the procedure bel- low for ...

  • Page 82: -Memo-

    E -memo- 6m8-f9-17-5 2/4/03 9:49 am page 10

  • Page 83: Chapter 6

    Emp00010 chapter 6 index index ........................................................6-1 1 2 3 4 5 6 e 6m8-f9-17-6 2/4/03 9:47 am page 1.

  • Page 84: Index

    6-1 e emp10010 index a adjusting trim angle ..............................3-17 air vent screw...........................................2-2 b basic boating rules (rules of the road) ...................................1-6 break in (running in) engine ...................3-8 c changing gear oil...........

  • Page 85

    6-2 e start-in-gear protection.........................1-13 starter will not operate............................5-6 starting engine.......................................3-10 steering friction adjustment ...................2-6 stopping engine.....................................3-15 storing outboard...

  • Page 86: Canada

    Emu01599 important warranty information for u.S.A. And canada welcome to the yamaha family! Congratulations on the purchase of your new yamaha marine power. Yamaha is commit- ted to exceptional customer satisfaction, and we want your ownership experience to be a satisfying one. Please read the follo...

  • Page 87

    5. Your warranty applies specifically to repairs made in the country of purchase. If your u.S.-purchased yamaha needs warranty service while in canada, or your canadian pur- chased yamaha needs service while in the united states, yamaha will assist the local dealer whenever possible. However, some p...

  • Page 88

    Emu00912* yamaha motor corporation, u.S.A. Outboard motor two year limited warranty yamaha motor corporation, u.S.A. Is proud of its heritage and reputation for producing products with high standards of quality and workmanship. Product excellence provides the cornerstone for our commitment to custom...

  • Page 89

    Specific parts excluded from warranty. Parts replaced due to normal wear or routine maintenance such as oil, spark plugs, shear pins, propellers, hubs, fuel and oil filters, brushes for the starter motor and power tilt motor, water pump impellers, and anodes, are not covered by warranty. Charges for...

  • Page 90

    Customer service if your machine requires warranty service, you must take it to any authorized yamaha outboard dealer within the continental united states. Be sure to bring your warranty registration identification or other valid proof of the original date of purchase. If a question or problem arise...

  • Page 91

    Emu01178 important warranty information if you use your yamaha outside u.S.A. Or canada welcome to the yamaha family! Congratulations on the purchase of your new yamaha marine power. Yamaha is com- mitted to exceptional customer satisfaction, and we want your ownership experience to be a satisfying ...

  • Page 92

    Printed in france january 2003-0.5 × 1 ! 6m8-f8199-17 (8cmh) (e) printed on recycled paper 6m8-f9-17 hyoushi 1/7/03 14:12 page 4.

  • Page 93

    Warranty card 12/6/01 7:40 pm page 1.

  • Page 94

    Warranty card 12/6/01 7:40 pm page 2.