Yamaha CD-S3000 Service Manual

Manual is about: Owners Manual

Summary of CD-S3000

  • Page 1

    P.O.Box 1, hamamatsu, japan service manual compact disc player cd-s3000 1 0 1 2 7 3 '13.10 ■ contents to service personnel ........................................2–4 prevention of electrostatic discharge ......5 front panels .............................................................6 rear panels...

  • Page 2

    This product contains chemicals known to the state of california to cause cancer, or birth defects or other reproductive harm. Do not place solder, electrical/electronic or plastic components in your mouth for any reason whatsoever! Avoid prolonged, unprotected contact between solder and your skin! ...

  • Page 3

    Warning: laser safety this product contains a laser beam component. This component may emit invisible, as well as visible radiation, which may cause eye damage. To protect your eyes and skin from laser radiation, the following precautions must be used during servicing of the unit. 1) when testing an...

  • Page 4

    The primary side of the power supply carries live mains voltage when the player is connected to the mains even when the player is switched off ! This primary area is not shielded so it is possible to accidentally touch copper tracks and/or components when servicing the player. Service personnel have...

  • Page 5

    Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called electrostatically sensitive (es) devices. Examples of typical es devices are integrated circuits and some field-effect transistors and semiconductor “chip” components. The follow...

  • Page 6

    ■ front panels u, k, a, b, g, l, v, j models t model 6 cd-s3000 cd-s30 0 0

  • Page 7

    ■ rear panels u, v models u model v model bottom view 7 cd-s3000 cd-s30 0 0

  • Page 8

    A, b, g, l models k model t model a model b, g models 8 cd-s3000 cd-s30 0 0

  • Page 9

    J model 9 cd-s3000 cd-s30 0 0

  • Page 10

    ■ remote control panel cdx30 ■ specifications / 参考仕様 ■ audio section / オーディオ部 output level / 出力レベル (1 khz, 0 db) sa-cd / cd .......................................................................2.0 ±0.3 v signal to noise ratio / 信号対雑音比 (ihf-a network) (1 khz, 0 db) sa-cd / cd .........................

  • Page 11

    Dimensions (w x h x d) / 寸法(幅 × 高さ × 奥行き) ............................... 435 x 142 x 440 mm (17-1/8" x 5-5/8" x 17-3/8") weight / 質量 ............................................................................. 19.2 kg (42.3 lbs.) finish / 仕上げ k, a, g, l, v models .....................................

  • Page 12

    ■ internal view front (1) p.C.B. Digital p.C.B. Front (2) p.C.B. Audio p.C.B. Power transformer for audio front (7) p.C.B. Module board loader mechanism unit power transformer for digital/front front (5) p.C.B. Front (3) p.C.B. Front (4) p.C.B. Front (6) p.C.B. Top view front view 1 2 3 4 5 6 7 8 9 ...

  • Page 13

    Top panel トップパネル side panel l サイドパネル l front panel unit フロントパネルユニット hook フック hook フック side panel r サイドパネル r hook フック hook フック cb913 cb911 front (5) p.C.B. Front (6) p.C.B. ① ④ ③ ② ⑥ ⑧ ⑧ ② ⑤ ■ disassembly procedures / 分解手順 fig. 1 (remove parts in the order as numbered.) disconnect the power cable fro...

  • Page 14

    Lid リッド disc tray ディスクトレイ bottom side 底面 flatblade screwdriver マイナスドライバー ⑦ disc tray ディスクトレイ 3. Removal of front panel a. Using a flatblade screwdriver, move the slider at the bottom in the direction of the arrow shown below. (fig. 2) * at this time, the disc tray is not pushed out. B. Push out the ...

  • Page 15

    Front frame assembly フロントフレーム ass'y front (3) p.C.B. Audio p.C.B. Digital p.C.B. 8p connector 8p コネクター * to cb909 on front (3) p.C.B. Cb1 te301 cb908 cb909 ⑩ ⑪ ⑩ ⑨ ⑨ ⑨ cb910 cable color of te301 red 1 2 3 4 5 6 black gray blue brown white rear view ⑬ ⑫ fig. 5 fig. 4 4. Removal of front frame assembl...

  • Page 16

    6. Removal of loader mechanism unit a. Remove 3 screws (⑭). (fig. 6) b. Remove cb402, cb404 and cb407. (fig. 6) c. Remove the loader mechanism unit. (fig. 6) 6. ローダーメカユニットの外し方 a. ⑭ のネジ 3 本を外します。(fig. 6) b. Cb402、cb404、cb407 を外します。(fig. 6) c. ローダーメカユニットを外します。(fig. 6) fig. 6 loader mechanism unit ローダー...

  • Page 17

    Loader mechanism unit ローダーメカユニット top view ① ② ② lid リッド “ ” (open/close) key “ ”(開閉)キー aligned to the same position 同じ位置に揃える ● when installing the loader mechanism unit: when installing the loader mechanism unit, adjust its inclination so that the clearance between the front panel and lid becomes eq...

  • Page 18

    5. Turning screw (③), adjust the lid so that it becomes horizontal viewed from the front. (fig. C) to change the position upward, loosen screw (③) by turning it clockwise. To change the position downward, tighten screw (③) by turning it counterclockwise. * turn screw (③) gradually and slowly. * be s...

  • Page 19

    7. Adjust the lid so that the clearance around the disc tray becomes equal viewed from the front. (fig. E) 8. Using a flatblade screwdriver, move the slider at the bottom in the direction of the arrow shown below. (fig. F) * at this time, the disc tray is not pushed out. 9. Push out the disc tray by...

  • Page 20

    Digital p.C.B. Front (1) p.C.B. Front (2) p.C.B. Cb901 cb406 ⑱ ⑱ ⑱ ⑲ te901 st907 st908 st905 st906 cb410 ⑮ black 1 2 3 4 cable color of te901 gray brown red cable color of st905 to st908 red gray brown blue 7. Removal of digital p.C.B. A. Remove 2 screws (⑮). (fig. 7) b. Remove 7 screws (⑯) and scre...

  • Page 21

    10. Removal of power transformer a. Remove 4 screws ( ). (fig. 9) b. Remove the power transformer for digital p.C.B. / front p.C.B. Together with the support. (fig. 9) c. Remove 4 screws ( ). (fig. 9) d. Remove the power transformer for audio p.C.B. Together with the support. (fig. 9) 10. 電源トランスの外し方...

  • Page 22

    When checking the audio p.C.B.: • put the rubber sheet and cloth over this unit. Then place the p.C.B.S upside down on the cloth and check it. (fig. 10) • reconnect all cables (connectors) that have been disconnected. • when connecting the flexible flat cable, be careful with polarity. • in this uni...

  • Page 23

    ● disassembly of loader mechanism unit 1. Removal of module board a. Solder the lands in the p.C.B. Of the loader mechanism unit with the anti-static soldering iron. (fig. 11) ● ローダーメカユニットの分解手順 1. モジュール基板の外し方 a. ローダーメカユニットの p.C.B. 上の端子間を静電 気対策はんだこてを使用してショートします。 (fig. 11) fig. 11 pattern side to shor...

  • Page 24

    Rear block リアブロック cd traverse mechanism cdトラバースメカ clamp assembly クランプ ass'y holder pu/sa-cd ホルダー pu/sa-cd disc tray ディスクトレイ front block フロントブロック loading belt ローディングベルト loading belt ローディングベルト 2. Removal of loading belt a. Remove 6 screws ( ) and then remove the clamp assembly. (fig. 12) b. Push out t...

  • Page 25

    When the following parts are replaced, the firmware must be updated to the latest version. Digital p.C.B. Main microprocessor: ic404 on digital p.C.B. ● confirmation of firmware version and checksum before and after updating the firmware, check the firmware version and checksum by using the self- di...

  • Page 26

    Pin no.2 rxd pin no.2 rxd pin no.3 txd pin no.3 txd pin no.5 gnd pin no.5 gnd pin no.7 rts pin no.7 rts pin no.8 cts pin no.8 cts pin no.2 rxd pin no.2 rxd pin no.3 txd pin no.3 txd pin no.5 gnd pin no.5 gnd pin no.7 rts pin no.7 rts pin no.8 cts pin no.8 cts • rs-232c conversion adaptor (version 4....

  • Page 27

    Sw7 sw4 t dsp ucom t r ucom dsp r rs-232c conversion adaptor rs-232c 変換アダプター ● 接続 ※ 本機の電源コードを ac コンセントから抜きます。 ・ rs-232c 変換アダプターのスイッチを下記のよう に設定します。(fig. 1) ・ 本機のトップパネルを外します。 (詳細は 分解手順 を参照してください。) ・ 本機の書き込み用ポート(digital p.C.B. の cb403) と pc のシリアルポート (rs-232c)を下記のよう に接続します。 (fig. 2) switches setting / ス...

  • Page 28

    ● operation procedures 1. Set the “standby/on / off” (power) (u, k, a, b, g, l, v models) / “ ” (power) (t model) switch to the “on” position. 2. Connect the power cable of this unit to the ac outlet. The power to this unit is supplied and the microprocessor is in the writing mode. 3. Start up flash...

  • Page 29

    6. [setting]をクリックし、通信速度の設定を行い ます。(fig. 5) 6. Click [setting], and set the baud rate. (fig. 5) fig. 5 5. [refer...]をクリックし、書き込むファームウェア を選択します。(fig. 4) ※ id、および mcu type は書き込みファイル選 択後、自動的に取り込まれます。(fig. 4) [ok]をクリックします。(fig. 4) 5. Click [refer...] and select the firmware name. (fig. 4) * the id and mcu ...

  • Page 30

    9. ファームウェアの書き込みが完了すると、以下の 画面が表示されます。(fig. 7) [ok]をクリックします。(fig. 7) 10. [exit]をクリックして flashsta.Exe を終了します。 (fig. 7) 9. When writing of the firmware is completed, the screen appears as shown below. (fig. 7) click [ok]. (fig. 7) 10. Click [exit] to end flashsta.Exe. (fig. 7) fig. 7 11. 本機の電源コードを ac コンセ...

  • Page 31

    ■ self-diagnostic function / ダイアグ(自己診断機能) this unit has self-diagnostic functions that are intended for inspection, measurement and location of faulty point. There are 9 main menu items, each of which has sub- menu items. Listed in the table below are main menu items and sub- menu items. Note: some ...

  • Page 32

    Caution! Using this unit with the protection function disabled may cause further damage to this unit. Use special care for this point when using this mode. ● starting self-diagnostic function in the protection cancel mode if the protection function works and causes hindrance to troubleshooting, canc...

  • Page 33

    ● canceling self-diagnostic function 1. Before canceling self-diagnostic function, execute setting for “4. Factory preset” menu. (memory initialized). * to keep the user memory, do not make setting. 2. Set the “standby/on / off” (power) (u, k, a, b, g, l, v models) / “ ” (power) (t model) switch to ...

  • Page 34

    ● operation procedure of main menu and sub-menu there are 9 main menu items, each of which has sub- menu items. Main menu and sub-menu selection select the main menu using “ ” (forward) and “ ” (reverse) keys. Parameter selection select the parameter by pressing the “layer” key. ● メインメニューとサブメニューの操作 ...

  • Page 35

    ● details of self-diagnostic function menu 1. Rom version/checksum this menu is used to display the firmware version and checksum. The checksum is obtained by adding the data at every 8-bit and expressing the result as a hexadecimal notation. * numeric values in the figure are given as reference onl...

  • Page 36

    Front view fl display fl ディスプレイ ① ② ③ ⑦ ⑥ ⑤ ④ 2 - 1 . - - - - - - keys of this unit / 本機キー front panel key key name / キー名称 ① pure direct d i r e c t ② source s o u r c e ③ layer l a y e r ④ o p e n ⑤ p l a y ⑥ p a u s e ⑦ s t o p key name / キー名称 2. Front panel key check this menu is used to check op...

  • Page 37

    3. Fl display check this menu is used to check operation of the fl display and indicator. 3. Fl display check fl 表示とインジケーターの動作をチェックします。 3-1. Fl display menu initial display 初期表示 3-2. All segment on / 全セグメント点灯 * after check, change to next menu at once. ※ 確認後、すみやかに次のサブメニューを選択してください。 3-3. All segment ...

  • Page 38

    4. Factory preset this menu is used to initialization of the back-up data. 5. Ad data check this menu is used to display the voltage value of the microprocessor which detects protection functions of this unit by using the sub-menu. 5-1. Prv_l l channel power supply protection detection detected: +12...

  • Page 39

    5-2. Prv_r r channel power supply protection detection detected: +12vr, -12vr, +5vr, +3.3vr, ac_r detection port: 81 pin of main microprocessor (ic404 on digital p.C.B.) normal value: 0.71 v to 2.84 v 5-3. Prv_d digital circuit power supply protection detection detected: +12d, -12d, +7d, +3.3d, ac_d...

  • Page 40

    6. Protection history this menu is used to display the history of protection function. 6-1. History 1 to history 4 the display is changed by pressing the “layer” key. 7. External connenction check not for service. 8. Audio check not for service. 6-2. Reset initialization of the protection history is...

  • Page 41

    9. Tray check this menu is used to check the loader mechanism unit. 9-1. Clamp down/tray open check check that the clamp moves down and the disc tray opens. 9-2. Tray close/clamp up check check that the disc tray closes, clamp moves up and automatic reproduction starts. 9. Tray check ローダーメカユニットの動作チェ...

  • Page 42

    ● v901 : 013st087gink (front (3) p.C.B.) ● pin connection ● grid assignment ● anode connection 1 43 note: 1) f1, f2 ..... Filament 2) np ..... No pin 3) nx ..... No extended pin 4) lgnd ..... Logic gnd pin 5) pgnd ..... Power gnd pin 6) vh ..... High voltage supply pin 7) vdd ..... Logic voltage sup...

  • Page 43

    Ic404: r5f364aenfa (digital p.C.B.) microprocessor * no replacement part available. / サービス部品供給なし ■ ic data timer (16-bit) internal peripheral functions inputs (timer b): 6 three-phase motor control circuit outputs (timer a): 5 watchdog timer (15-bit) remote control signal receiver (2 circuits) pwm f...

  • Page 44

    Pin no. Port name function name (p.C.B.) i/o detail of function p o w eron standb y mcusleep eep w riting [when wr iting] 1 p9_6/anex1/sout4 fl_ex_mosi so o o fl driver control data output extended ic: data out for lc709004a 2 p9_5/anex0/clk4 fl__ex_clk o o o fl driver control clock output extended ...

  • Page 45

    Pin no. Port name function name (p.C.B.) i/o detail of function p o w eron standb y mcusleep eep w riting [when wr iting] 34 p6_4/ncts1/nrts1/ncts0/ clks1 wr_busy o o o [mcu] for simple emulation / busy output when writing flash 35 p6_3/txd0/sda0 dac_sda so o o dac ess9018s control i2c data input/ou...

  • Page 46

    Pin no. Port name function name (p.C.B.) i/o detail of function p o w eron standb y mcusleep eep w riting [when wr iting] 66 p2_6/an2_6/a6 pwr_ry o o o power relay control 67 p2_5/int7/an2_5/a5 acpwr_det irq o o ac power input detection 68 p2_4/int6/an2_4/a4 cd_pwr_det i o o vaddis886 sdram clock en...

  • Page 47

    Sa-cd module m16c/64a r5f364aenfa microprocessor ic404 loader mechanism unit g2: serial port rxd. Ic413 flash rom 16mbit en29lv160cb-70t ic401 ssp2 upd800500f1-011 pin [15,17]: dp,dm j4: peo2 pin [23,24]: xo,xi +3.3usb d6: sdo0 e1: wclk0 e3: bclk f1: sysclk k4: peo3 a5: sdo1 ic424 dir/dit pcm9210ptr...

  • Page 48

    Flexible flat cable flexible flat cable under side view to front (3) (cb909) 90˚ mountain fold 90˚ valley fold to digital (cb405) letter side wire length exposed on the upper side excluding housing route the twisted wires (ovoid from entering area) letter side letter side letter side to loader mecha...

  • Page 49

    Flexible flat cable flexible flat cable bend letter side letter side letter side to module board (cn201) to module board (cn210) to digital (cb407) 50 mm (2") 10 mm (3/8") 100 mm (3-7/8") cn210 cn213 cn205 cn201 cn211 to digital (cb407) to digital (cb402) letter side to module board (cn205) module b...

  • Page 50

    Ic406 ic430 cb41 0 cb403 cb41 4 ic424 cb408 cb409 ic41 3 ic420 ic402 ic403 ic41 0 ic404 ic408 ic405 ic438 ic409 cb406 cb402 cb405 cb407 cb404 ic419 ic418 ic407 ic401 ic441 ic421 jk401 ic443 cb443 digital (side a) no replacement part available. サービス部品供給なし usb optical coaxial optical coaxial digital i...

  • Page 51

    Digital (side b) a b c d e f g h i j 1 2 3 4 5 6 7 cd-s3000 51 ref no. Location d406 d3 d408 d3 d410 d3 • semiconductor location.

  • Page 52

    Jk1 ic6 ic29 ic30 ic7 cb1 ic8 ic1 ic2 audio (side a) digital (cb408) d_lock dac_scl dgnd sel_sdo_dsdr sel_spdif_dsdr dgnd sel_wck_dsdl +12ry -12ry dac_sda prv_l mute dgnd ry_audio dgnd d3.3v d3.3v sel_sdo_dsdl sel_bck_dsdclk dgnd prv_r dac_n_rst dgnd 1 1 1 16 10 20 11 48 32 17 33 64 49 6 3 4 1 6 3 4...

  • Page 53

    Audio (side b) a b c d e f g h i j 1 2 3 4 5 6 7 cd-s3000 53 ref no. Location d5 f4 d6 f6 d7 f3 d8 f6 d13 c4 d14 c5 d15 c5 d16 c5 d17 d3 d18 d3 • semiconductor location ref no. Location d19 d4 d20 d4 d21 d5 d22 d5 d23 d6 d24 d6 d303 i3 d304 i6 d305 i3 d306 i6 ref no. Location d307 g3 d308 g4 d309 g5...

  • Page 54

    Ic903 ic90 1 ic904 ic902 cb90 1 ic905 cb902 ic909 w902 front (1) (side a) digital (cb410) front (3) (cb908) +7mt +7mt mt_gnd mt_gnd +5mo1 +5mo1 mo_gnd mo_gnd +5mo2 +5mo2 nc nc prvd fl_pon +5d +5d +5d dgnd dgnd dgnd +12ry -12ry ry_gnd flgnd +vp acfl1 acfl2 br gr re bl to power transformer (for digita...

  • Page 55

    Ic903 ic90 1 ic904 ic902 cb90 1 ic905 cb902 ic909 w902 front (1) (side b) a b c d e f g h i j 1 2 3 4 5 6 7 cd-s3000 55 ref no. Location d902 c3 d904 c3 d905 c5 d907 c2 d909 c2 d914 e5 d915 e3 d916 f4 d917 e4 d918 f3 d957 g3 d958 g3 q903 f5 • semiconductor location.

  • Page 56

    Ic907 cb91 1 ic908 jk903 jk901 jk902 w903 w901 front (2) (side a) front (6) (side a) front (7-1) (side a) front (7-2) (side a) digital (cb406) ac in system connector remote in out +9sub pwr_det ry_pwr mgnd +3.3m n_res rem_rear sys_txd sys_rxd 5 k-ohms 10 w re gr bu br power transformer (for digital/...

  • Page 57

    Ic909 front (2) (side b) front (6) (side b) front (7-1) (side b) front (7-2) (side b) 1 4 3 5 a b c d e f g h i j 1 2 3 4 5 6 7 cd-s3000 57 ref no. Location d921 h4 d922 h4 d924 g4 d925 g4 d926 c4 d928 h4 d929 c4 d931 b4 d932 b4 d933 b3 d934 b3 d935 c3 d937 c3 d959 d3 d960 d2 d961 c3 d962 c3 d963 c3...

  • Page 58

    W904 cb91 0 cb908 cb909 cb913 cb912 w905 ic910 ic911 front (3) (side a) front (4) (side a) front (5) (side a) +3.3m +3.3s dgnd led_power fl_ex_data fl_ex_cl ex_n_cs ex_n_ic key2 +3.3m +3.3s dgnd led_power fl_ex_data fl_ex_cl ex_n_cs ex_n_ic key2 power indicator pure direct source rayer pure direct i...

  • Page 59

    Ic910 ic911 front (3) (side b) front (4) (side b) front (5) (side b) 1 7 14 8 1 12 24 13 a b c d e f g h i j 1 2 3 4 5 6 7 cd-s3000 59 ref no. Location d938 e2 d939 e2 d940 i2 d941 i2 d942 g3 d943 h2 d944 h2 d948 g5 • semiconductor location ref no. Location d949 g6 d954 g6 d955 g6 ic910 g2 ic911 e6 ...

  • Page 60

    ■ pin connection diagrams • ics • diodes • transistors 1 9 8 4 1 51 50 31 81 80 100 30 1 1 2 3 4 3 1 5 4 50 75 76 1 51 25 26 100 6 3 1 48 13 37 24 1 12 36 25 1 3 4 5 1 3 4 5 1 3 4 5 8 4 1 25 48 1 24 1 16 17 32 33 48 49 64 1 4 8 1 10 20 1 3 22 a 1 ab a 1 22 ab 1: out 2: com 3: in 3: output 1: common ...

  • Page 61: Schematic Diagrams

    A 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n 61 digital 1/3 cd-s3000 schematic diagrams ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked and must be replaced with parts having specifications equal to those originally instal...

  • Page 62

    A 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n cd-s3000 62 digital 2/3 ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed. ★ schematic di...

  • Page 63

    A 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n 63 digital 3/3 cd-s3000 ★ components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed. ★ schematic diagram is subject to change without notice. ● 印のある部品は、安全性確保部品を示しています...

  • Page 64

    A 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n cd-s3000 64 audio 1/2 ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed. ★ schematic diag...

  • Page 65

    A 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n 65 audio 2/2 cd-s3000 ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed. ★ schematic diag...

  • Page 66

    A 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n cd-s3000 66 front 1/3 ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed. ★ schematic diag...

  • Page 67

    A 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n 67 front 2/3 cd-s3000 ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed. ★ schematic diag...

  • Page 68

    A 1 2 3 4 5 6 7 8 9 10 b c d e f g h i j k l m n cd-s3000 68 front 3/3 ★ all voltages are measured with a 10mΩ/v dc electronic voltmeter. ★ components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed. ★ schematic diag...

  • Page 69

    • electrical component parts warning ● components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed. ● 印のある部分は、安全確保部品を示しています。部品の交換が必要な場合、パーツリストに記載されている部品を使用し てください。 ● 部品価格ランクは、予告なく変更することがあります。 ■ replacement parts list ...

  • Page 70

    Digital * zf862300 p.C.B. Digital j PCB DIGITAL * zf862400 p.C.B. Digital utkalv PCB DIGITAL * zf862500 p.C.B. Digital b PCB DIGITAL * zf862600 p.C.B. Digital g PCB DIGITAL cb402 wk469100 cn.Fmn fmn 29p te FMNコネクター 03 cb403 vq047200 cn.Bs.Pin 9p コネクター 01 cb404 vb389800 cn.Bs.Pin 2p コネクター 01 cb405 vm...

  • Page 71

    Digital c466 us064100 c.Ce.Chp 0.01uf 50v b チップセラコン 01 c467-468 us062100 c.Ce.Chp 100pf 50v b チップセラコン 01 c469 us035100 c.Ce.Chp 0.1uf 16v b チップセラコン 01 c470 us061100 c.Ce.Chp 10pf 50v b チップセラコン 01 c471 us064100 c.Ce.Chp 0.01uf 50v b チップセラコン 01 c472 us035100 c.Ce.Chp 0.1uf 16v b チップセラコン 01 c474 wc6668...

  • Page 72

    Digital c552 us135100 c.Ce.Chp 0.1uf 16v チップセラコン 01 c555-556 us063470 c.Ce.Chp 4700pf 50v b チップセラコン 01 c571-572 us063100 c.Ce.Chp 1000pf 50v b チップセラコン 01 c580 ur237330 c.El 33uf 16v ケミコン c581 ur238100 c.El 100uf 16v jutkalv ケミコン c581 uu238100 c.El 100uf 16v bg ケミコン 01 c582 us063100 c.Ce.Chp 1000pf 5...

  • Page 73

    Digital and audio ic424 yc213a00 ic pcm9210ptr IC ic430 x8897a00 ic r1172s331b-e2-f 電源IC 03 ic438 x5482a00 ic ne5532dr op amp アンプIC 01 * ic441 x9293a00 ic r1172h151d-t1-fe 電源IC 01 * jk401 v7808900 cn.Usb ubb 4p se USBジャック 03 pj401-402 wk897800 jack.Pin jack t6782-aaac ピンジャック 07 q401-402 vv556400 tr ...

  • Page 74

    Audio c89-90 we102100 c.Pp 2200pf 100v j PPコン 01 c95-96 us064100 c.Ce.Chp 0.01uf 50v b チップセラコン 01 c101-102 we101700 c.Pp 1000pf 100v j PPコン c107-108 we102100 c.Pp 2200pf 100v j PPコン 01 c109-110 us064100 c.Ce.Chp 0.01uf 50v b チップセラコン 01 c113-114 we101700 c.Pp 1000pf 100v j PPコン c119-124 we101700 c.Pp...

  • Page 75

    Audio q33 vv556400 tr 2sc2412k q,r,s トランジスタ 01 q34 ww781800 tr.Dgt dta014eubtl デジタルトランジスタ 01 q35 v7421800 tr 2sa1312-gr,bl トランジスタ 01 q36 v7421700 tr.Chp 2sc3324-gr,bl チップトランジスタ 01 q37 v7421800 tr 2sa1312-gr,bl トランジスタ 01 q38 v7421700 tr.Chp 2sc3324-gr,bl チップトランジスタ 01 q39 v7421800 tr 2sa1312-gr,bl トラン...

  • Page 76

    Audio and front r120-123 wq835800 r.Mtl.Oxd 100Ω 1w 酸化金属被膜抵抗 02 r124-129 vi192500 r.Mtl.Chp 100Ω 1/10w チップ金属被膜抵抗 01 * r130-133 zg861700 r.Mtl.Oxd 200Ω 1w 酸化金属被膜抵抗 r142-147 vi199000 r.Mtl.Chp 47kΩ 1/10w チップ金属被膜抵抗 01 r148-159 vi193300 r.Mtl.Chp 220Ω 1/10w チップ金属被膜抵抗 01 r160-171 v8070900 r.Mtl.Flm 100Ω ...

  • Page 77

    Front c944 we102900 c.Pp 0.01uf 100v j PPコン c945 v6185300 c.Ce.Safty 0.01uf 275v 規格認定コンデンサ 01 c946-947 uu237100 c.El 10uf 16v ケミコン 01 c949 uu238100 c.El 100uf 16v ケミコン 01 c950 us063100 c.Ce.Chp 1000pf 50v b チップセラコン 01 c951 uu266100 c.El 1uf 50v ケミコン 01 c952 uu237470 c.El 47uf 16v ケミコン 01 c953 we1029...

  • Page 78

    D961-963 vt532500 diode 1sr154-400 ダイオード 01 f901 wg409800 fuse 2a 125v juv ヒューズ 01 f901 kb000750 fuse.Mini t2a 250v tkabgl ミニヒューズ 01 * ic901-903 yf323a00 ic ba05cc0t 5v 電源IC * ic904 yf429a00 ic ba07cc0t 7v 電源IC ic905 xj608a00 ic njm7812fa IC 02 ic906 xc721a00 ic njm7912fa -12v 電源IC 02 ic907-908 wj68...

  • Page 79

    Value 1/4w type part no. 1/6w type part no. 11 kΩ hf45 7110 hf45 7110 12 kΩ hj35 7120 hf85 7120 13 kΩ hf45 7130 hf45 7130 15 kΩ hf45 7150 hf45 7150 18 kΩ hf45 7180 hf45 7180 22 kΩ hf45 7220 hf45 7220 24 kΩ hf45 7240 hf45 7240 27 kΩ hj35 7270 hf85 7270 30 kΩ hf45 7300 hf45 7300 33 kΩ hf45 7330 hf45 7...

  • Page 80

    166 37 37 164 164 231 165 165 165 164 166 166 166 101 166 166 166 120 166 164 167 167 300 303 302 166 166 166 201 165 166 165 164 164 174 210 164 164 164 164 166 166 175 166 166 103 166 166 168 168 165 165 169 169 163 163 163 163 18 17 40 41 202 204 204 200 165 166 166 166 173 173 172 211 172 166 16...

  • Page 81

    * 1 zf861000 p.C.B. Assembly front j PCB FRONT * 1 zf861100 p.C.B. Assembly front uv PCB FRONT * 1 zf861200 p.C.B. Assembly front tkal PCB FRONT * 1 zf861300 p.C.B. Assembly front b PCB FRONT * 1 zf861400 p.C.B. Assembly front g PCB FRONT * 2 zf861700 p.C.B. Assembly audio j PCB AUDIO * 2 zf861800 p...

  • Page 82

    • loader mechanism unit * 1 zf861000 p.C.B. Assembly front j PCB FRONT * 1 zf861100 p.C.B. Assembly front uv PCB FRONT * 1 zf861200 p.C.B. Assembly front tkal PCB FRONT * 1 zf861300 p.C.B. Assembly front b PCB FRONT * 1 zf861400 p.C.B. Assembly front g PCB FRONT 5-5 wv414400 flexible flat cable 24p ...

  • Page 83

    ■ remote control schematic diagram panel key no. Layout key code 1. Option 2. Ras30 cdx30 r1 1 ohm 1/4w q1 r2 100 ohms r3 10 ohms d1 x1 4.0 mhz c1 47 uf c2 0.1 uf vdd e2 xin e0 g0 g1 2 e2 3 e1 19 carr 20 vdd 1 vss 4 xin 5 xout 6 e0 7 g0 8 g1 9 g2 10 g3 11 d7 12 d6 13 d5 14 d4 15 d3 16 d2 17 d1 18 d0...

  • Page 84

    ■ playback of music files stored on a pc digital in coaxial optical usb balanced out pc rear panel of cd-s3000 usb cable (type b) cd-s3000 84.

  • Page 85

    ■ パソコンに保存された音楽の再生 digital in coaxial optical usb balanced out cd-s3000 リアパネル パソコン usb ケーブル(type b) 85 cd-s3000 cd-s30 0 0

  • Page 86

    86 cd-s3000 cd-s30 0 0

  • Page 87

    Memo 87 cd-s3000 cd-s30 0 0 87.

  • Page 88: Cd-S3000

    Cd-s3000