DL manuals
Yamaha
Software
DME24N
Owner's Manual Supplement

Yamaha DME24N Owner's Manual Supplement

Other manuals for DME24N: Setup Manual, Owner's Manual, Owner's Manual, Owner's Manual, Owner's Manual, Owner's Manual, Setup Manual

Manual is about: DME Designer

Page of 8

Download

Print this page

Bookmark us

Notes for DME64N/DME24N Version 1.2

Thank you for purchasing the DME64N/DME24N. The following notes supplement the information in the Owner’s Manual

about DME64N/DME24N.

■

An Edit Indicator has been added.

If a parameter is changed after recalling a scene, a dot

will appear in the scene number indicator, and “EDIT”

will appear in the display.

■

The User-de

ned parameters display is changed.

“No Assign” settings in DME Designer are displayed as

dotted lines.

When [Parameter Value Edit] is selected the display will

be a solid line.

When [Direct Parameter Value], [Scene Change], [GPI

Out], or [Play Wav File] are selected, the display will be

inverted.

■

The Remote parameter has been added to Utility display “Misc” page.

• The REMOTE connector can be used as a MIDI connector.

• A new communications protocol allows AMX, Crestron, and other external devices to control the DME.

For details about the communication protocol refer to the “DME-N Remote Control Protocol Specifications” document.

The “DME-N Remote Control Protocol Specifications” document can be found at the Yamaha Pro Audio website:

http://www.yamahaproaudio.com/

Added parameters are shown in bold.

Upgrading Cautions

• The following parameter will not be reflected in Version 1.2 when it is used to read data created in Version 1.0.0: SlotIn/SlotOut.

Remake these settings in DME Designer Version 1.2.

• Data created using Version 1.2 will not open properly on Version 1.1.

• Version 1.2 will not work with previous version in the area. When using Version 1.2, all DME firmware (program and components),

along with DME Designer, must be upgraded to Version 1.2 simultaneously. For instructions on performing the version upgrade,

see “DME Firmware Update” in Chapter 3 “Main Panel Window” of the “DME Designer Version 1.2 Owner’s Manual.”

• To use the DME CONTROL function on the PM5D, the PM5D must be version 1.12 or later, and connected DME64N/24N units

must be version 1.1 or later.

• For details about DME CONTROL function settings in the PM5D, see the “PM5D/PM5D-RH Owner’s Manual.”

Changes in Version 1.2

HA Control (422)

External head amp control (RS-422 only)

COM (232C)

Control using the DME communication protocol via RS-232C/RS-422.

COM (422)

MIDI (232C)

Control using MIDI commands via RS-232C/RS-422.

MIDI (422)

Remote Ctrl (232C)

Remote controller via RS-232C/RS-422.

Remote Ctrl (422)

1 2 3 4 5 6 7 Next › »

Summary of DME24N

Page 1
Notes for dme64n/dme24n version 1.2 thank you for purchasing the dme64n/dme24n. The following notes supplement the information in the owner’s manual about dme64n/dme24n. ■ an edit indicator has been added. If a parameter is changed after recalling a scene, a dot will appear in the scene number indic...
Page 2
Notes for dme64n/dme24n version 1.2 2 for information on changes to dme designer, see the “dme designer version 1.2 owner’s manual.” ■ the default gateway ip address is changed. In version 1.0, the default ip gateway address was ***.***.***.1, but in version 1.1, the address is changed to ***.***.**...
Page 3
3 notes for dme64n/dme24n version 1.2 mode: summing sums all input signals coming from inputs (-12db), without regard to device or card type, and outputs it through all outputs. ■ the event scheduler function allows day/time settings for events the settings are accessible via the utility display “mi...
Page 4
Notes for dme64n/dme24n version 1.2 4 3. User label function lets you attach names to assigned parameters. For details about settings, see the “dme designer version 1.2 owner’s manual.” ■ a gpi lock function has been added. This functions allows you to disable input from a gpi device. For details ab...
Page 5
5 notes for dme64n/dme24n version 1.2 2. Setting the monitoring point from dme designer (probe monitor function) for details, see the “dme designer version 1.2 owner’s manual.” when you use the probe monitor function, the monitoring point switches and the [monitor] indicator lights up. At the same t...
Page 6
Notes for dme64n/dme24n version 1.2 6 message list message content corrective action cannot select there is no selectable item in the scene or monitoring point list. Data is not registered.Register the data to be used in dme designer. Cas. In sync err the word clock input from the [cascade in] termi...
Page 7
7 notes for dme64n/dme24n version 1.2 recovering the dme64n/24n program update has failed. Restoring the previous program. Do not turn off the power while this display is on the screen. Retry the program update. If the update is still unsuccessful after several retries, a malfunction is likely. Cont...
Page 8
The following notes supplement the information in the dme64n/dme24n owner’s manual dme24n analog input characteristics • 0dbu = 0.775 vrms • all ad converters (ch1-8) are 24-bit linear, 128 times oversampling. • +48v dc (phantom power) is supplied to ch input (1-8) connectors via each individual con...