1. DL manuals
  2. Yamaha
  3. Outboard Motor
  4. F200C
  5. Service Manual

Yamaha F200C Service Manual

Other manuals for F200C: Owner's Manual, Owner's Manual, Owner's Manual

Summary of F200C

  • Page 1

    F200c lf200c f225c lf225c service manual 69j-28197-1f-11 lit-18616-02-76 *lit186160276*.

  • Page 2

    Notice this manual has been prepared by yamaha primarily for use by yamaha dealers and their trained mechanics when performing maintenance procedures and repairs to yamaha equipment. It has been written to suit the needs of persons who have a basic understanding of the mechanical and electrical conc...

  • Page 3: Contents

    Contents general information 1 gen info specifications 2 spec periodic checks and adjustments 3 chk adj fuel system 4 fuel power unit 5 powr lower unit 6 lowr bracket unit 7 brkt electrical systems 8 elec troubleshooting 9 trbl shtg index – +.

  • Page 4: General Information

    Gen info 69j1d11 general information how to use this manual ................................................................................. 1-1 manual format............................................................................................ 1-1 symbols........................................

  • Page 5

    69j1d11 1 2 3 4 5 6 7 8 9 predelivery checks ...................................................................................... 1-28 checking the fuel system ........................................................................ 1-28 checking the gear oil..........................................

  • Page 6

    Gen info general information 1-1 69j1d11 how to use this manual 1 manual format the format of this manual has been designed to make service procedures clear and easy to under- stand. Use the information below as a guide for effective and quality service. 1 parts are shown and detailed in an exploded...

  • Page 7

    69j1d11 1-2 1 2 3 4 5 6 7 8 9 symbols the symbols below are designed to indicate the content of a chapter. General information specifications periodic checks and adjustments fuel system power unit lower unit bracket unit electrical systems troubleshooting gen info spec chk adj fuel powr lowr brkt el...

  • Page 8

    Gen info general information 1-3 69j1d11 safety while working 1 to prevent an accident or injury and to ensure quality service, follow the safety pro- cedures provided below. Fire prevention gasoline is highly flammable. Keep gasoline and all flammable products away from heat, sparks, and open flame...

  • Page 9

    69j1d11 1-4 1 2 3 4 5 6 7 8 9 6. Keep a supply of clean, lint-free cloths for wiping up spills, etc. Good working practices special tools use the recommended special tools to pro- tect parts from damage. Use the right tool in the right manner—do not improvise. Tightening torques follow the tightenin...

  • Page 10

    Gen info general information 1-5 69j1d11 1 model name 2 approved model code 3 transom height 4 serial number model name approved model code starting serial no. F200tr 60l 1001799– lf200tr 60m 1000373– f225tr 69j 1007259– lf225tr 69k 1002513–.

  • Page 11

    69j1d11 1-6 1 2 3 4 5 6 7 8 9 features and benefits 1 newly developed v6 4-stroke engine the f225 is a newly developed 60-degree v6 4-stroke engine with a very compact and lightweight design. Its size and weight are almost the same as the v6 2-stroke engines that are in current use. This f225 offers...

  • Page 12

    Gen info general information 1-7 69j1d11 crankcase the crankcase is made of cast aluminum, however steel has been cast into the areas for the crank- shaft bearings. By distinguishing the area that requires strength from the area that allows the use of a lighter material, both weight reduction and a ...

  • Page 13

    69j1d11 1-8 1 2 3 4 5 6 7 8 9 piston the piston has been carved out of a forged stock. To prevent the valves from coming in contact with the piston, the piston is provided with a valve recess. If the engine goes out of timing and a valve opens when the piston is at top-dead-center, this recess preve...

  • Page 14

    Gen info general information 1-9 69j1d11 valve train system the valve train consists of a total of four camshafts, with two in each bank. The camshafts are driven with the combination of a belt and chains. The crankshaft turns the belt to drive the exhaust camshafts in both banks. Chains connect the...

  • Page 15

    69j1d11 1-10 1 2 3 4 5 6 7 8 9 tensioner a timing chain tensioner is provided at the mid-span of the timing chain, between both camshafts. The timing chain tensioner uses the force of a spring to maintain its tension. After the engine is started, oil is pumped into the tensioner, and the resulting p...

  • Page 16

    Gen info general information 1-11 69j1d11 intake system throttle valve a total of six intake throttle valves are provided, one for each cylinder. Together with the intake silencer that offers enhanced intake efficiency and the injectors that are provided at each throttle body, the throttle valves he...

  • Page 17

    69j1d11 1-12 1 2 3 4 5 6 7 8 9 exhaust passage during idle to reduce noise when the engine is idling, the exhaust gas passage of the f225 has adopted a lab- yrinth construction. During idling, the exhaust gas passes through the passage on the side of the exhaust guide, and enters the upper case thro...

  • Page 18

    Gen info general information 1-13 69j1d11 fuel system the fuel flows in the following order: fuel filter, low-pressure fuel pump, vapor separator, high-pres- sure fuel pump, and injectors. The excess fuel at the injectors passes through the pressure regula- tor and fuel cooler, and returns to the va...

  • Page 19

    69j1d11 1-14 1 2 3 4 5 6 7 8 9 low-pressure fuel pump the f225 has adopted a newly developed, low-pressure electrical fuel pump, in place of the low- pressure mechanical fuel pump used in the previous electronic fuel injection system. With the adop- tion of the electric pump, the routing of the fuel...

  • Page 20

    Gen info general information 1-15 69j1d11 electronic control system the ecm controls the ignition timing, the fuel injection timing, the fuel injection volume, and the isc and it maintains a stoichiometric air-fuel ratio in all operating conditions, including starting and idling. Also, the ecm conve...

  • Page 21

    69j1d11 1-16 1 2 3 4 5 6 7 8 9 ignition and fuel injection timing this engine adopted the group injection system that the fuel required for one combustion is injected twice per one cycle. Therefore, the injector driving circuits can be integrated to 3 circuits and a simpler electrical struc- ture is...

  • Page 22

    Gen info general information 1-17 69j1d11 ptt (power trim and tilt) unit the ptt unit has been newly developed for the f225. Based on the field-proven 61a type, its ptt fluid passage and internal valve construction have been changed for this application. Although the valves of the 61a type have been...

  • Page 23

    69j1d11 1-18 1 2 3 4 5 6 7 8 9 technical tips 1 fuel injection control the f200/f225 injects fuel simultaneously to the following cylinder pairs: #1 and #4, #2 and #5, and #3 and #6. Optimal injection timing is provided in accordance with the operating conditions of the engine. Starting fuel injecti...

  • Page 24

    Gen info general information 1-19 69j1d11 over-revolution control if the engine speed exceeds 4,500 r/min, while the shift is in neutral, ignition is stopped. The various stages of ignition cutoff are shown in the table below. Ignition cutoff cylinder in neutral : indicates a misfire at either cylin...

  • Page 25

    69j1d11 1-20 1 2 3 4 5 6 7 8 9 fail-safe function table symptom fail-safe function diagnosis code ignition injection isc engine condition incorrect pulser coil signal engine starting: only the cylinders outputting normal signal ignite at btdc10°, and all cylinders thereafter. All cylinders inject si...

  • Page 26

    Gen info general information 1-21 69j1d11 ptt (power trim and tilt) unit in the newly designed ptt unit, the up-main valve, down-main valve, up-relief valve, and down- relief valve have been concentrated in the gear pump housing in order to improve the serviceability of the engine and ensure reliabl...

  • Page 27

    69j1d11 1-22 1 2 3 4 5 6 7 8 9 trim-up and tilt-up function when the ptt switch is pressed to “up,” the power trim and tilt motor operates the gear pump and fluid pressure is generated. As a result, the fluid pressure pushes the up-shuttle piston upward, enters the trim cylinder and tilt cylinder lo...

  • Page 28

    Gen info general information 1-23 69j1d11 trim ram retraction function when the outboard motor is tilted up and held in place with the tilt stop lever and the ptt switch is pressed to “dn,” the trim ram will be retracted. Although the gear pump attempts to draw oil from the tilt cylinder and trim cy...

  • Page 29

    69j1d11 1-24 1 2 3 4 5 6 7 8 9 trim-down and tilt-down function when the ptt switch is pressed to “dn,” the power trim and tilt motor operates the gear pump and fluid pressure is generated. As a result, the fluid pressure pushes the down-shuttle piston upward, enters the tilt cylinder upper chamber ...

  • Page 30

    Gen info general information 1-25 69j1d11 stationary condition when the ptt switch is not pressed, the gear pump will not pump the fluid, the up-main valve and the down-main valve will remain closed, and the ptt unit in the system remains constant. This will allow the tilt ram and the trim ram to ma...

  • Page 31

    69j1d11 1-26 1 2 3 4 5 6 7 8 9 cooling system 1 cooling water inlet 2 water pump 3 oil pan 4 exhaust pipe 5 pcv (pressure control valve) 6 in-bank exhaust system 7 thermostat 8 propeller boss È water lubrication system : s69j1460 sleeve piston crankshaft pin crankshaft journal retur n route retur n ...

  • Page 32

    Gen info general information 1-27 69j1d11 propeller selection 1 the performance of a boat and outboard motor will be critically affected by the size and type of propeller you choose. Propellers greatly affect boat speed, acceleration, engine life, fuel economy, and even boating and steering capabili...

  • Page 33

    69j1d11 1-28 1 2 3 4 5 6 7 8 9 predelivery checks 1 to make the delivery process smooth and efficient, the predelivery checks should be completed as explained below. Checking the fuel system 1. Check that the fuel hoses are securely connected and that the fuel tank is full with fuel. Caution: this i...

  • Page 34

    Gen info general information 1-29 69j1d11 checking the outboard motor mounting height 1. Check that the anti-cavitation plate is aligned with the bottom of the boat. If the mounting height is too high, cavitation will occur and propulsion will be reduced. Also, the engine speed will increase abnorma...

  • Page 35

    69j1d11 1-30 1 2 3 4 5 6 7 8 9 checking the steering wheel 1. Check the steering friction for proper adjustment. 2. Check that the steering operates smoothly. 3. Check that there is no interference with wires or hoses when the outboard motor is steered. Checking the gearshift and throttle operation ...

  • Page 36

    Gen info general information 1-31 69j1d11 checking the cooling water pilot hole 1. Check that cooling water is discharged from the cooling water pilot hole. Test run 1. Start the engine, and then check that the gearshift operates smoothly. 2. Check the engine idle speed after the engine has been war...

  • Page 37: Specifications

    69j1d11 spec 1 2 3 4 5 6 7 8 9 specifications general specifications................................................................................... 2-1 maintenance specifications .......................................................................... 2-3 power unit...............................

  • Page 38

    Spec specifications 2-1 69j1d11 general specifications 2 item unit model f200tr lf200tr f225tr lf225tr dimension overall length mm (in) 892 (35.1) overall width mm (in) 634 (25.0) overall height (x) mm (in) 1,805 (71.1) (u) mm (in) — 1,932 (76.1) boat transom height (x) mm (in) 635 (25.0) (u) mm (in...

  • Page 39

    69j1d11 2-2 1 2 3 4 5 6 7 8 9 (*1) pon: pump octane number = (ron + motor octane number)/2 ron: research octane number (*2) cca: cold cranking ampere mca: marine cranking ampere abyc: american boat and yacht council sae: society of automotive engineers rc: reserve capacity fuel and oil fuel type reg...

  • Page 40

    Spec specifications 2-3 69j1d11 maintenance specifications 2 power unit item unit model f200tr lf200tr f225tr lf225tr power unit minimum compression pressure (*1) kpa (kgf/cm 2 , psi) 880 (8.8, 125) lubrication oil pressure (*2) kpa (kgf/cm 2 , psi) at 700 r/min 650 (6.5, 924) cylinder heads warpage...

  • Page 41

    69j1d11 2-4 1 2 3 4 5 6 7 8 9 2nd ring dimension b mm (in) 1.17–1.19 (0.0461–0.0468) dimension t mm (in) 3.6–3.8 (0.142–0.150) end gap mm (in) 0.30–0.45 (0.0118–0.0177) side clearance mm (in) 0.03–0.07 (0.0012–0.0027) oil ring dimension b mm (in) 2.40–2.47 (0.0945–0.0972) dimension t mm (in) 2.3–2.7...

  • Page 42

    Spec specifications 2-5 69j1d11 valve springs free length mm (in) 44.20 (1.740) minimum free length mm (in) 42.60 (1.677) tilt limit mm (in) 1.5 (0.06) valve lifters valve lifter outside diameter mm (in) 32.98–33.00 (1.2984–1.2992) valve lifter-to-cylinder head clearance mm (in) 0.02–0.05 (0.0008–0....

  • Page 43

    69j1d11 2-6 1 2 3 4 5 6 7 8 9 lower unit oil pump discharge at 97–103 °c (207–217 °f) with 10w-40 engine oil l (us gal, imp gal)/min at 700 r/min 8.8 (2.32, 1.94) pressure kpa (kgf/cm 2 , psi) 138 (1.38, 19.62) relief valve opening pressure kpa (kgf/cm 2 , psi) 529–647 (5.29–6.47, 75.22–92.00) therm...

  • Page 44

    Spec specifications 2-7 69j1d11 electrical item unit model f200tr lf200tr f225tr lf225tr ignition and ignition control system pulser coil output peak voltage (w/r – b, w/b – b, w/g – b) at cranking (unloaded) v 5.3 at cranking (loaded) v 5.3 at 1,500 r/min (loaded) v 20 at 3,500 r/min (loaded) v 43 ...

  • Page 45

    69j1d11 2-8 1 2 3 4 5 6 7 8 9 fuel control system fuel injector resistance (*1) at 20 °c (68 °f) Ω 14.0–15.0 starter motor type sliding gear output kw 1.4 cranking time limit second 30 brushes standard length mm (in) 15.5 (0.61) wear limit mm (in) 9.5 (0.37) commutator standard diameter mm (in) 29.0...

  • Page 46

    Spec specifications 2-9 69j1d11 power trim and tilt system trim sensor setting resistance Ω 9–11 resistance (p – b) Ω 9–387.6 fluid type atf dexron ii brushes standard length mm (in) 12.0 (0.47) wear limit mm (in) 4.0 (0.16) commutator standard diameter mm (in) 25.0 (0.98) item unit model f200tr lf2...

  • Page 47: — Memo —

    69j1d11 2-10 1 2 3 4 5 6 7 8 9 — memo — maintenance specifications.

  • Page 48

    Spec specifications 2-11 69j1d11 dimensions exterior s69j2130 w5 a1 t1 w1 l7 h9 h1 h11 h2 h4 h3 h7 h8 h10 l8 l5 a2 h6 l9 l4 a3 12˚ c3 l2 l1 l10 l6.

  • Page 49

    69j1d11 2-12 1 2 3 4 5 6 7 8 9 symbol unit model f200tr lf200tr f225tr lf225tr l1 mm (in) 651 (25.6) l2 mm (in) 219 (8.6) l3 mm (in) — l4 mm (in) 673 (26.5) l5 (x) mm (in) 59 (2.3) (u) mm (in) — 59 (2.3) l6 (x) mm (in) 1,155 (45.5) (u) mm (in) — 1,272 (50.1) l7 mm (in) 618 (24.3) l8 mm (in) 230 (9.1...

  • Page 50

    Spec specifications 2-13 69j1d11 clamp bracket symbol unit model f200tr lf200tr f225tr lf225tr b1 mm (in) 125 (4.9) b2 mm (in) 254 (10.0) b3 mm (in) 163 (6.4) b4 mm (in) 51 (2.0) b5 mm (in) 180 (7.1) b6 mm (in) 411 (16.2) b7 mm (in) — b8 mm (in) — b9 mm (in) 19 (0.7) c2 mm (in) — c3 mm (in) 79 (3.1)...

  • Page 51

    69j1d11 2-14 1 2 3 4 5 6 7 8 9 tightening torques 2 specified torques part to be tightened thread size tightening torques n·m kgf·m ft·lb fuel system fuel filter holder bolt m6 8 0.8 5.8 fuel filter bracket bolt m6 8 0.8 5.8 intake air temperature sensor — 4 0.4 2.9 low-pressure fuel pump bracket bo...

  • Page 52

    Spec specifications 2-15 69j1d11 spark plug — 25 2.5 18 cylinder head bolt 1st m10 19 1.9 14 2nd 37 3.7 27 3rd 90° 1st m8 14 1.4 10 2nd 28 2.8 20 engine hanger bolt m6 12 1.2 8.7 cooling water cover bolt m6 12 1.2 8.7 starboard cylinder head plug — 23 2.3 17 cylinder block plug — 23 2.3 17 engine te...

  • Page 53

    69j1d11 2-16 1 2 3 4 5 6 7 8 9 upper case mount nut — 72 7.2 52 engine oil drain bolt m14 27 2.7 19 apron stay — 8 0.8 5.8 pressure control valve — 8 0.8 5.8 upper exhaust guide bolt m8 20 2.0 14 m10 42 4.2 30 oil strainer bolt m6 10 1.0 7.2 oil pan bolt m8 20 2.0 14 exhaust manifold bolt m8 20 2.0 ...

  • Page 54

    Spec specifications 2-17 69j1d11 general torques this chart specifies tightening torques for standard fasteners with a standard iso thread pitch. Tightening torque specifications for special components or assemblies are provided in applicable sections of this man- ual. To avoid warpage, tighten mult...

  • Page 55

    69j1d11 chk adj 1 2 3 4 5 6 7 8 9 periodic checks and adjustments special service tools ..................................................................................... 3-1 maintenance interval chart............................................................................ 3-2 top cowling ......

  • Page 56

    Chk adj periodic checks and adjustments 3-1 69j1d11 special service tools 3 fuel pressure gauge yb-06766 inductive self-powered tachometer yu-08036-b battery powered timing light ym-33277-a pressure/vacuum tester yb-35956-a.

  • Page 57

    69j1d11 3-2 1 2 3 4 5 6 7 8 9 maintenance interval chart 3 use the following chart as a guideline for general maintenance. Adjust the maintenance intervals according to the operating conditions of the outboard motor. Item remarks initial every refer to page 10 h ours (b reak-in) 50 h ours (3 months ...

  • Page 58

    Chk adj periodic checks and adjustments 3-3 69j1d11 note: (*1) if equipped with a portable fuel tank. (*2) be sure to replace the timing belt every 1,000 hours of operation or every five years. (*3) the engine should be flushed with fresh water after operating in salt, turbid, or muddy water. (*4) d...

  • Page 59

    69j1d11 3-4 1 2 3 4 5 6 7 8 9 top cowling 3 checking the top cowling 1. Check the fitting by pushing the cowling with both hands. Adjust if necessary. 2. Loosen the bolts 1. 3. Move the hook 2 up or down slightly to adjust its position. Note: • to loosen the fitting, move the hook in direction a. • ...

  • Page 60

    Chk adj periodic checks and adjustments 3-5 69j1d11 measuring the fuel pressure (high-pressure fuel line) 1. Remove the cap 1. 2. Install the fuel pressure gauge onto the pressure check valve. 3. Turn the engine start switch to on, and then measure the fuel pressure. Note: after the engine start swi...

  • Page 61

    69j1d11 3-6 1 2 3 4 5 6 7 8 9 changing the engine oil using an oil changer 1. Start the engine and warm it up. 2. Remove the engine oil dipstick and oil filler cap 1. 3. Insert the tube of the oil changer 2 into the dipstick guide 3. 4. Operate the oil changer to extract the oil. Note: be sure to cl...

  • Page 62

    Chk adj periodic checks and adjustments 3-7 69j1d11 note: be sure to clean up any oil spills. 5. Install the drain bolt, and then tighten it to the specified torque. 6. Pour the specified amount of the recom- mended engine oil into the oil filler hole. 7. Install the oil filler cap and dipstick, and...

  • Page 63

    69j1d11 3-8 1 2 3 4 5 6 7 8 9 5. Install the oil filter, and then tighten it to the specified torque using a 72.5 mm (2.9 in) oil filter wrench. 6. Pour the specified amount of the recom- mended engine oil into the oil filler hole. 7. Install the oil filler cap and dipstick, and then start the engin...

  • Page 64

    Chk adj periodic checks and adjustments 3-9 69j1d11 5. Check the spark plug gap a. Adjust if out of specification. 6. Install the spark plug, tighten it finger tight b, then to the specified torque with a spark plug wrench c. Checking the thermostat note: for checking procedures, see chapter 5, “che...

  • Page 65

    69j1d11 3-10 1 2 3 4 5 6 7 8 9 adjusting the throttle link and throttle cable operation (with a stop bolt) note: • be sure to synchronize the throttle valves before adjusting the throttle link. • for synchronizing procedures, see chapter 4, “synchronizing the throttle valve.” 1. Loosen the locknut 1...

  • Page 66

    Chk adj periodic checks and adjustments 3-11 69j1d11 9. Place the throttle cam 0 against the fully closed stopper f, and check that there is a minimum clearance g of approxi- mately 1.0 mm (0.04 in). 10. Adjust the position of the throttle cable joint until its hole is aligned with the set pin h on ...

  • Page 67

    69j1d11 3-12 1 2 3 4 5 6 7 8 9 5. Check that the alignment mark a is between the alignment marks b. If not, repeat steps 2–4. 6. Place the throttle cam 7 against the fully closed stopper c, and check that there is a minimum clearance d of approxi- mately 1.0 mm (0.04 in). 7. Adjust the position of t...

  • Page 68

    Chk adj periodic checks and adjustments 3-13 69j1d11 5. Adjust the position of the shift cable joint until its hole is aligned with the set pin. Caution: the shift cable joint must be screwed in a minimum of 8.0 mm (0.31 in) c. 6. Connect the cable joint, install the clip, and then tighten the lockn...

  • Page 69

    69j1d11 3-14 1 2 3 4 5 6 7 8 9 note: • to increase the idle speed, turn the throttle stop screw in direction a. • to decrease the idle speed, turn the throttle stop screw in direction b. 7. Tighten the port throttle stop screw 5 until it contacts the throttle body lever 6. 8. Loosen the locknut 8, r...

  • Page 70

    Chk adj periodic checks and adjustments 3-15 69j1d11 caution: the throttle cable joint must be screwed in a minimum of 8.0 mm (0.31 in) h. 14. Connect the cable joint, install the clip, and then tighten the locknut. 15. Check the throttle cable for smooth oper- ation and adjust the cable length, if ...

  • Page 71

    69j1d11 3-16 1 2 3 4 5 6 7 8 9 note: be sure to listen to the winding sound of the power trim and tilt motor for smooth opera- tion. 2. Fully tilt the outboard motor up, and then support it with the tilt stop lever 1 to check the lock mechanism of the lever. Checking the power trim and tilt fluid le...

  • Page 72

    Chk adj periodic checks and adjustments 3-17 69j1d11 note: if the oil is at the correct level, the oil should overflow out of the check hole when the check screw is removed. 3. If necessary, add sufficient gear oil of the recommended type until it overflows out of the check hole. 4. Install the chec...

  • Page 73

    69j1d11 3-18 1 2 3 4 5 6 7 8 9 checking the lower unit (for air leakage) 1. Remove the check screw 1, and then install the special service tool. 2. Apply the specified pressure to check whether the lower unit can hold it for at least 10 seconds. Caution: do not over pressurize the lower unit, oth- e...

  • Page 74

    Chk adj periodic checks and adjustments 3-19 69j1d11 caution: do not oil, grease, or paint the anodes, otherwise they will be ineffective. 2. Replace the anodes and trim tab if excessively eroded. Checking the battery 1. Check the battery electrolyte level. If the level is at or below the minimum le...

  • Page 75

    69j1d11 3-20 1 2 3 4 5 6 7 8 9 lubrication 1. Apply water resistant grease to the areas shown. General.

  • Page 76

    Chk adj periodic checks and adjustments 3-21 69j1d11 note: apply grease to the grease nipple until it flows from the bushings a. 2. Apply corrosion resistant grease to the areas shown..

  • Page 77: Fuel System

    69j1d11 fuel 1 2 3 4 5 6 7 8 9 fuel system special service tools ..................................................................................... 4-1 hose routing ................................................................................................... 4-2 fuel and blowby hoses..........

  • Page 78

    Fuel fuel system 4-1 69j1d11 special service tools 4 pressure/vacuum tester yb-35956-a digital multimeter yu-34899-a test harness (3 pins) yb-06793 carburetor synchronizer yu-08030

  • Page 79

    69j1d11 4-2 1 2 3 4 5 6 7 8 9 hose routing 4 fuel and blowby hoses 1 blowby hose 2 fuel hose (fuel joint-to-fuel filter) 3 fuel hose (fuel filter-to-fuel pump) 4 fuel hose (fuel pump-to-vapor separator) 5 fuel hose (vapor separator-to-fuel pump) 6 high-pressure fuel hose (vapor separator-to-starboar...

  • Page 80

    Fuel fuel system 4-3 69j1d11 intake silencer, fuel filter, and fuel pump 4.

  • Page 81

    69j1d11 4-4 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 cover 1 2 bolt 3 m6 × 28 mm 3 bolt 1 m6 × 16 mm 4 washer 1 5 holder 1 6 bolt 1 m6 × 14 mm 7 bracket 1 8 bolt 2 m6 × 19 mm 9 cap 1 10 fuel hose 7 11 fuel joint 1 12 o-ring 1 not reusable 13 fuel filter element 1 14 spring 1 15 o-ring 1 not re...

  • Page 82

    Fuel fuel system 4-5 69j1d11 vapor separator 4.

  • Page 83

    69j1d11 4-6 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 float chamber 1 2 cover 1 3 high-pressure fuel pump 1 4 float 1 5 water hose 1 6 fuel hose 3 7 joint 1 8 fuel cooler 1 9 washer 2 10 nut 2 11 water hose 1 12 bracket 1 13 bolt 3 m8 × 16 mm 14 collar 6 15 bushing 4 16 bolt 4 m8 × 16 mm 17 hos...

  • Page 84

    Fuel fuel system 4-7 69j1d11 removing the hose clamps 1. Remove the hose clamps by cutting the joint. Caution: if the hose clamps are removed without cutting the joint first, the fuel hose will be damaged. Installing the hose clamps 1. Crimp the hose clamps properly to securely fasten them. Warning ...

  • Page 85

    69j1d11 4-8 1 2 3 4 5 6 7 8 9 warning always reduce the fuel pressure in the high-pressure fuel line before servicing the line or the vapor separator. If the fuel pressure is not released, pressurized fuel may spray out. 3. Remove the cap 3, and then press in the valve b using a thin screwdriver 2. ...

  • Page 86

    Fuel fuel system 4-9 69j1d11 intake manifold and high-pressure fuel line 4.

  • Page 87

    69j1d11 4-10 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 hose 1 2 high-pressure fuel hose 4 3 clamp 7 4 joint 2 5 joint 2 6 screw 2 7 washer 4 8 throttle position sensor 1 9 screw 2 10 bracket 1 11 bracket 1 12 screw 2 m5 × 15 mm 13 bracket 1 14 joint 1 15 o-ring 1 not reusable 16 metal gasket 2 ...

  • Page 88

    Fuel fuel system 4-11 69j1d11.

  • Page 89

    69j1d11 4-12 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 starboard intake manifold 1 2 throttle body #1 1 3 throttle body #3 1 4 throttle body #5 1 5 starboard fuel rail 1 6 port intake manifold 1 7 throttle body #2 1 8 throttle body #4 1 9 throttle body #6 1 10 port fuel rail 1 11 pressure regul...

  • Page 90

    Fuel fuel system 4-13 69j1d11 throttle control 4.

  • Page 91

    69j1d11 4-14 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 bracket 1 2 joint 1 3 magnet control lever 1 4 pin 4 5 shaft 1 6 bracket 1 7 bolt 2 m6 × 20 mm 8 washer 2 9 bushing 5 10 gear 2 11 throttle control lever 1 12 circlip 1 13 bolt 1 14 wave washer 1 15 washer 1 16 throttle cam 1 17 spring 1 18...

  • Page 92

    Fuel fuel system 4-15 69j1d11 removing the pressure regulator 1. Remove the intake silencer and the port intake manifold. 2. Disconnect the hose 1 and 2, and then remove the pressure regulator 3. Disconnecting the high-pressure fuel hose joint 1. Disconnect the high-pressure fuel hose joint 1 with t...

  • Page 93

    69j1d11 4-16 1 2 3 4 5 6 7 8 9 synchronizing the throttle valve 1. Loosen the bank synchronizing screw 1. 2. Remove the port link rod 2 and star- board link rod 3. 3. Loosen the starboard throttle stop screw 4 until it separates from the throttle body lever 5. 4. Loosen the synchronizing screw 6 of ...

  • Page 94

    Fuel fuel system 4-17 69j1d11 10. Turn the engine start switch to on. 11. Measure the throttle position sensor out- put voltage. Adjust the throttle position sensor b position if out of specification. 12. Tighten the synchronizing screw 6 of cylinder #3 and stop tightening it when the throttle posit...

  • Page 95

    69j1d11 4-18 1 2 3 4 5 6 7 8 9 15. Tighten the synchronizing screw 0 of cylinder #4, and stop tightening when the throttle plate starts to move. Similarly, tighten and adjust the synchronizing screw a of cylinder #6. 16. Tighten the port throttle stop screw 8 until it contacts the throttle body leve...

  • Page 96

    Fuel fuel system 4-19 69j1d11 19. Measure the vacuum of cylinders #1, #3, and #5. Repeat step 12 if out of specifi- cation. 20. Measure the vacuum of cylinders #2, #4, and #6. Repeat step 12 if out of specifi- cation. 21. Check the average vacuum difference between the port and starboard banks. Adju...

  • Page 97

    69j1d11 4-20 1 2 3 4 5 6 7 8 9 25. Check that there is no clearance a between the port and starboard throttle stop screws 4 and 8, and the throttle body levers 5 and 9. If there is any clearance, repeat step 24. 26. Start the engine, and when the engine speed is at idle, check the average vac- uum d...

  • Page 98: Power Unit

    Powr 69j1d11 power unit special service tools ..................................................................................... 5-1 power unit....................................................................................................... 5-3 checking the compression pressure ...............

  • Page 99

    69j1d11 1 2 3 4 5 6 7 8 9 cylinder block .............................................................................................. 5-43 disassembling the cylinder block ............................................................ 5-47 checking the piston diameter ..................................

  • Page 100

    Powr power unit 5-1 69j1d11 special service tools 5 compression gauge yu-33223-1 compression gauge extension yb-06563 test harness (3 pins) yb-06769 flywheel magnet holder yb-06139 universal puller yb-06117 valve spring compressor ym-01253 valve spring compressor attachment yb-06320 valve guide remo...

  • Page 101

    69j1d11 5-2 1 2 3 4 5 6 7 8 9 piston ring compressor ym-08037 special service tools.

  • Page 102

    Powr power unit 5-3 69j1d11 power unit 5.

  • Page 103

    69j1d11 5-4 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 power unit 1 2 screw 4 3 cover 1 4 dipstick 1 5 bolt 1 m6 × 20 mm 6 dipstick guide 1 7 o-ring 1 not reusable 8 plastic tie 2 not reusable 9 fuel hose 1 10 bolt 2 m6 × 10 mm 11 ptt motor lead 2 sky blue, light green 12 gasket 1 not reusable 1...

  • Page 104

    Powr power unit 5-5 69j1d11.

  • Page 105

    69j1d11 5-6 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 nut 1 2 washer 1 3 flywheel magnet 1 4 screw 4 m6 × 30 mm 5 stator coil 1 6 bolt 4 m6 × 35 mm 7 blowby hose guide 1 8 blowby hose 1 9 blowby hose 1 10 stator coil bracket 1 11 collar 2 12 woodruff key 1 13 plastic tie 5 not reusable 14 wirin...

  • Page 106

    Powr power unit 5-7 69j1d11.

  • Page 107

    69j1d11 5-8 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 wiring harness 1 2 bracket 1 3 bolt 1 m6 × 20 mm 4 ground lead 3 5 bolt 1 m6 × 16 mm 6 bracket 1 7 bolt 4 m6 × 16 mm 8 ecm 1 9 bolt 2 m6 × 25 mm 10 power trim and tilt relay 1 11 cap 2 12 nut 4 13 washer 2 14 cap 1 15 spring washer 2 16 batt...

  • Page 108

    Powr power unit 5-9 69j1d11 no. Part name q’ty remarks 1 starter motor 1 2 nut 1 3 spring washer 1 4 battery cable 1 from terminal and power trim and tilt relay 5 bolt 3 m8 × 45 mm 6 bolt 1 m6 × 20 mm 7 ground lead 1 8 bolt 2 m6 × 35 mm 9 rectifier regulator 1 10 gasket 1 not reusable 11 cover 1 12 ...

  • Page 109

    69j1d11 5-10 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 ignition coil 3 2 bolt 6 m6 × 20 mm 3 bolt 6 m6 × 20 mm 4 bracket 1 5 clamp 3 6 clamp 3 7 screw 3 m6 × 20 mm 8 plate 1 9 gasket 1 10 grommet 1 11 idle speed control hose 1 power unit.

  • Page 110

    Powr power unit 5-11 69j1d11.

  • Page 111

    69j1d11 5-12 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 bolt 1 m6 × 30 mm 2 washer 1 3 link rod arm 1 4 plug 1 5 o-ring 1 not reusable 6 bolt 2 m6 × 20 mm 7 link rod 1 long 8 link rod 1 short 9 link rod 1 10 nut 3 11 oil filler cap 1 12 o-ring 1 not reusable 13 oil filler neck 1 14 bolt 2 m6 × 4...

  • Page 112

    Powr power unit 5-13 69j1d11 no. Part name q’ty remarks 1 timing belt 1 2 bolt 4 m5 × 45 mm 3 drive sprocket 1 4 plate 1 5 woodruff key 1 6 timing belt tensioner 1 7 bolt 2 m10 × 35 mm 8 driven sprocket 2 9 dowel pin 2 10 bolt 28 m6 × 30 mm 11 port cylinder head cover 1 12 gasket 1 not reusable 13 s...

  • Page 113

    69j1d11 5-14 1 2 3 4 5 6 7 8 9 checking the compression pressure 1. Start the engine, warm it up for 5 min- utes, and then turn it off. 2. Remove the clip from the engine stop lanyard switch on the remote control box. 3. Remove the ignition coil cover and all spark plugs, and then install the specia...

  • Page 114

    Powr power unit 5-15 69j1d11 5. Check the oil pressure. Check the oil pump, oil leakage, and oil strainer if out of specification. Checking the oil pressure sensor 1. Connect the test harness (3 pins) to the oil pressure sensor. 2. Start the engine and warm it up for 5 min- utes. 3. Measure the oil ...

  • Page 115

    69j1d11 5-16 1 2 3 4 5 6 7 8 9 note: do not turn the flywheel magnet counter- clockwise. 4. Check the intake and exhaust valve clearance for cylinder #4. 5. Turn the flywheel magnet an additional 120° clockwise and align the “2tdc” mark g on the flywheel magnet with the pointer b. 6. Check the intak...

  • Page 116

    Powr power unit 5-17 69j1d11 10. Turn the flywheel magnet an additional 120° clockwise and align the “1tdc” mark on the flywheel magnet with the pointer, and check that the “i” marks on the driven sprockets are aligned with the alignment marks on the cylinder head. 11. Remove the flywheel magnet. Ca...

  • Page 117

    69j1d11 5-18 1 2 3 4 5 6 7 8 9 15. Remove the driven sprockets. Note: hold the camshaft with a wrench, and be careful not to damage the driven sprocket. 16. Remove the timing chain tensioners b, then the camshaft caps in the order shown in the illustration. 17. Remove the camshafts and timing chains...

  • Page 118

    Powr power unit 5-19 69j1d11 23. Install the camshaft caps, and then tighten them to the specified torque in the order shown in the illustration. 24. Install the timing chain tensioners b, and then tighten the bolts to the specified torque in the sequence shown. Note: • install the camshaft caps in ...

  • Page 119

    69j1d11 5-20 1 2 3 4 5 6 7 8 9 28. Install the woodruff key. 29. Install the flywheel magnet. Caution: apply force in the direction of the arrows shown, to prevent the flywheel holder from slipping off easily. Note: apply engine oil to the flywheel magnet nut before installation. 30. Turn the flywhe...

  • Page 120

    Powr power unit 5-21 69j1d11 35. Install the ignition coil cover, wiring har- ness guide, and flywheel magnet cover. Replacing the timing belt 1. Remove the flywheel magnet cover, igni- tion coil cover, and intake silencer. 2. Turn the flywheel magnet clockwise and align the “1tdc” mark a on the fly...

  • Page 121

    69j1d11 5-22 1 2 3 4 5 6 7 8 9 5. Disconnect the stator coil couplers 3 and pulser coil coupler 4, and remove the blowby hose 5 and stator coil bracket 6. 6. Remove the wiring harness guide bolts. Note: move the wiring harness guide 7 to a posi- tion that will make servicing easy. 7. Using a hexagon...

  • Page 122

    Powr power unit 5-23 69j1d11 caution: • do not twist, turn inside out, or bend the timing belt beyond the maximum limit of 25 mm (1.0 in) j, otherwise it may be damaged. • do not get oil or grease on the timing belt. 11. Turn the drive sprocket clockwise two turns, and then check that all alignment ...

  • Page 123

    69j1d11 5-24 1 2 3 4 5 6 7 8 9 3. Remove the dipstick guide 5, and dis- connect the fuel hose 6, ptt motor leads 7, and flushing device hose (flush- ing device model) 8. 4. Disconnect the fuel pump driver and iso- lator couplers, ptt switch coupler, shift cut switch coupler, neutral switch cou- pler...

  • Page 124

    Powr power unit 5-25 69j1d11 caution: • apply force in the direction of the arrows shown, to prevent the flywheel holder from slipping off easily. • to prevent damage to the engine or tools, screw in the flywheel puller set bolts evenly and completely so that the flywheel puller plate is parallel to...

  • Page 125

    69j1d11 5-26 1 2 3 4 5 6 7 8 9 2. Using a hexagon wrench, turn the timing belt tensioner 1 clockwise to push the timing belt, increase strength gradually, and then insert a ø5.0 mm (0.2 in) pin 2 into the hole g. 3. Remove the timing belt 3 from the driven sprocket side. 4. Remove the pin and timing...

  • Page 126

    Powr power unit 5-27 69j1d11 installing the sprockets and timing belt 1. Install the driven sprockets 1, and then tighten the bolts to the specified torque. 2. Check that “i” marks a and b on the driven sprockets are aligned with marks c and d. Align if necessary. 3. Install the new gaskets, cylinde...

  • Page 127

    69j1d11 5-28 1 2 3 4 5 6 7 8 9 7. Install the timing belt 6 from the drive sprocket side with its part number in the upright position, turn the belt a half turn counterclockwise to align it, and then remove the pin 5. 8. Turn the drive sprocket clockwise two turns, and then check that the alignment ...

  • Page 128

    Powr power unit 5-29 69j1d11 cylinder head 5.

  • Page 129

    69j1d11 5-30 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 timing chain tensioner 1 2 bolt 4 m6 × 25 mm 3 timing chain tensioner 1 4 bolt 32 m7 × 37 mm 5 bolt 4 m7 × 48 mm 6 camshaft cap 16 7 camshaft cap 2 8 timing chain 2 9 oil seal 2 not reusable 10 camshaft 3 1 11 camshaft 4 1 12 camshaft 2 1 1...

  • Page 130

    Powr power unit 5-31 69j1d11.

  • Page 131

    69j1d11 5-32 1 2 3 4 5 6 7 8 9 È tightening sequence no. Part name q’ty remarks 1 spark plug 6 2 bolt 16 m10 × 120 mm 3 bolt 4 m8 × 55 mm 4 bolt 2 m8 × 90 mm 5 port cylinder head 1 6 bolt 4 m6 × 20 mm 7 engine hanger 2 8 bolt 2 m6 × 12 mm 9 ground lead 1 10 gasket 1 not reusable 11 starboard cylinde...

  • Page 132

    Powr power unit 5-33 69j1d11 removing the cylinder head 1. Remove the exhaust cover bolts in the sequence shown. 2. Remove the timing chain tensioner 1 and camshaft caps in the sequence shown. 3. Remove the camshafts and timing chains, and disconnect the ground lead. 4. Remove the cylinder head bolt...

  • Page 133

    69j1d11 5-34 1 2 3 4 5 6 7 8 9 checking the valve springs 1. Measure the valve spring free length a. Replace if out of specification. 2. Measure the valve spring tilt b. Replace if out of specification. Checking the valves 1. Check the valve face for pitting or wear. Replace if necessary. 2. Measure...

  • Page 134

    Powr power unit 5-35 69j1d11 checking the valve guides note: before checking the valve guide make sure that the valve stem diameter is within specifi- cation. 1. Measure the valve guide inside diameter a. 2. Calculate the valve stem-to-valve guide clearance as follows. Replace the valve guide if out...

  • Page 135

    69j1d11 5-36 1 2 3 4 5 6 7 8 9 note: • turn the valve guide reamer clockwise to ream the valve guide. • do not turn the reamer counterclockwise when removing the reamer. 4. Measure the valve guide inside diameter. Replace the valve guide if out of specifi- cation. Checking the valve seat 1. Eliminat...

  • Page 136

    Powr power unit 5-37 69j1d11 2. Cut the surface of the valve seat with a 45° cutter by turning the cutter clockwise until the valve seat face has become smooth. A slag or rough surface caution: do not over cut the valve seat. Be sure to turn the cutter evenly downward at a pres- sure of 40–50 n (4–5...

  • Page 137

    69j1d11 5-38 1 2 3 4 5 6 7 8 9 b previous contact width 8. If the valve seat contact area is too nar- row and situated near the bottom edge of the valve face, use a 60° cutter to cut the bottom edge of the valve seat. If neces- sary, use a 45° cutter to center the area and set its width. B previous ...

  • Page 138

    Powr power unit 5-39 69j1d11 3. Measure the camshaft runout. Replace if out of specification. 4. Measure the camshaft journal diameter c and cylinder head journal inside diam- eter d. Replace the camshaft and cylin- der head if out of specification. 5. Calculate the camshaft oil clearance e as follo...

  • Page 139

    69j1d11 5-40 1 2 3 4 5 6 7 8 9 2. Check the cylinder head warpage using a straightedge 1 and thickness gauge 2 in six directions as shown. Replace if out of specification. Installing the valves 1. Install the new valve seal 1 to the valve guide. 2. Install the valve 2, valve spring 3, and valve spri...

  • Page 140

    Powr power unit 5-41 69j1d11 4. Lightly tap the valve spring retainer with a plastic hammer to set the valve cotter securely. Note: apply engine oil to the valve shims and valve lifters before installation. Installing the cylinder head 1. Install the new gaskets and cylinder heads, and then tighten ...

  • Page 141

    69j1d11 5-42 1 2 3 4 5 6 7 8 9 4. Install the camshaft caps, and then tighten the bolts to the specified torques in two stages and in the sequence shown. 5. Install the timing chain tensioners 1, and then tighten the bolts to the specified torque in the sequence shown. Note: • install the camshaft c...

  • Page 142

    Powr power unit 5-43 69j1d11 cylinder block 5.

  • Page 143

    69j1d11 5-44 1 2 3 4 5 6 7 8 9 È tightening sequence no. Part name q’ty remarks 1 crankcase cover 1 2 bolt 17 m8 × 45 mm 3 bolt 2 m6 × 20 mm 4 engine hanger 1 5 plate 1 6 screw 14 m4 × 8 mm 7 gasket 1 not reusable 8 nut 6 9 baffle plate 1 10 dowel pin 2 11 bolt 12 not reusable 12 connecting rod cap ...

  • Page 144

    Powr power unit 5-45 69j1d11.

  • Page 145

    69j1d11 5-46 1 2 3 4 5 6 7 8 9 È tightening sequence no. Part name q’ty remarks 1 crankshaft 1 2 cylinder block 1 3 crankcase 1 4 oil seal 1 not reusable 5 thrust bearing 2 6 thrust bearing 1 7 main bearing 4 8 main bearing 4 9 stud bolt 6 m8 × 95 mm 10 bolt 8 m10 × 105 mm 11 bolt 2 m8 × 95 mm 12 bo...

  • Page 146

    Powr power unit 5-47 69j1d11 disassembling the cylinder block 1. Remove the cooling water passage cover bolts in the sequence shown. 2. Remove the crankcase cover bolts in the sequence shown. Note: do not remove the ignition timing pointer from the crankcase cover. 3. Remove the baffle plate. 4. Rem...

  • Page 147

    69j1d11 5-48 1 2 3 4 5 6 7 8 9 checking the cylinder bore 1. Measure the cylinder bore (d 1 –d 6 ) at measuring points a, b, and c, and in direction d (d 1 , d 3 , d 5 ), which is parallel to the crankshaft, and direction e (d 2 , d 4 , d 6 ), which is at a right angle to the crankshaft. A 20 mm (0....

  • Page 148

    Powr power unit 5-49 69j1d11 checking the piston ring grooves 1. Measure the piston ring grooves. Replace the piston if out of specification. Checking the piston ring side clearance 1. Measure the piston ring side clearance. Replace the piston and piston rings as a set if out of specification. Check...

  • Page 149

    69j1d11 5-50 1 2 3 4 5 6 7 8 9 checking the piston pin 1. Measure the piston pin diameter. Replace if out of specification. Checking the connecting rod small end inside diameter 1. Measure the connecting rod small end inside diameter a. Replace the connect- ing rod if out of specification. Checking ...

  • Page 150

    Powr power unit 5-51 69j1d11 2. Measure the crankshaft runout. Replace the crankshaft if out of specification. Checking the crankpin oil clearance 1. Clean the bearings and the connecting rod. 2. Install the upper half of the bearing into the connecting rod 1 and the lower half into the connecting r...

  • Page 151

    69j1d11 5-52 1 2 3 4 5 6 7 8 9 note: align the marks b on the connecting rod cap and connecting rod, which you made during disassembly. 6. Tighten the connecting rod bolts to the specified torques in three stages. Note: • reuse the removed connecting rod bolts when checking the oil clearance. • do n...

  • Page 152

    Powr power unit 5-53 69j1d11 3. Select the suitable color b for the con- necting rod bearing from the table. Checking the crankshaft main journal oil clearance 1. Clean the bearings, main journals, and bearing portions of the crankcase and cylinder block. 2. Place the cylinder block upside down on a...

  • Page 153

    69j1d11 5-54 1 2 3 4 5 6 7 8 9 9. Tighten the crankcase bolts to the speci- fied torques in two stages and in the sequence shown. Note: • crankcase bolts 1–f can be reused five times. • do not move the crankshaft until the main journal oil clearance measurement has been completed. • tighten crankcas...

  • Page 154

    Powr power unit 5-55 69j1d11 3. Select the suitable main bearing number c from the table. Note: • example: if the crankshaft journal mark a is “81” and the cylinder block mark b is “04,” then the main bearing number c is “1.” • main bearing #3 is a thrust bearing. Disassembling the oil pump 1. Remov...

  • Page 155

    69j1d11 5-56 1 2 3 4 5 6 7 8 9 note: install the oil seals using a general pipe of the proper size. Assembling the piston and cylinder block 1. Assemble the piston 1, connecting rod 2, piston pin 3, and new piston pin clips 4. Note: • face the mark a on the connecting rod in the same direction as th...

  • Page 156

    Powr power unit 5-57 69j1d11 6. Install half of the bearings 9 into the cyl- inder block 0. 7. Insert the projection f of the bearing into the notch in the cylinder block. Note: install the main bearings in their original posi- tions. 8. Set the crankshaft a, and oil seal b, and thrust bearings c in...

  • Page 157

    69j1d11 5-58 1 2 3 4 5 6 7 8 9 note: • the oil seals must be installed before tight- ening the crankcase bolts. • apply engine oil to the crankcase bolts before installation. • tighten crankcase bolts 1–f to the speci- fied torques in two stages first, and then tighten crankcase bolts g–s to the spe...

  • Page 158

    Powr power unit 5-59 69j1d11 caution: before installing the oil pump, be sure to fill it with engine oil through the oil pas- sage k. 16. Install the baffle plate g to the specified torque. 17. Install the new gasket and crankcase cover, and then tighten the bolts to the specified torque in two stag...

  • Page 159

    69j1d11 5-60 1 2 3 4 5 6 7 8 9 20. Install the oil filter, and then tighten it to the specified torque using a 72.5 mm (2.9 in) oil filter wrench. Checking the thermostat 1. Remove the cover 1 and thermostat 2. 2. Suspend the thermostat in a container of water. 3. Place a thermometer in the water an...

  • Page 160

    Powr power unit 5-61 69j1d11 5. Install the dipstick guide 7, and connect the fuel hose 8, ptt motor leads 9, and flushing device hose (flushing device model) 0. 6. Connect the shift cable a and throttle cable b, and then adjust their lengths. For adjustment procedures, see chapter 3, “checking the ...

  • Page 161

    69j1d11 5-62 1 2 3 4 5 6 7 8 9 7. Install the holders c and retaining plate d. 8. Install the stator coil bracket and stator coil. 9. Install the woodruff key. 10. Install the flywheel magnet. Caution: apply force in the direction of the arrows shown, to prevent the flywheel holder from slipping off...

  • Page 162: Lower Unit

    Lowr 69j1d11 lower unit special service tools ..................................................................................... 6-1 lower unit (regular rotation model) ............................................................. 6-4 removing the lower unit .........................................

  • Page 163

    69j1d11 1 2 3 4 5 6 7 8 9 propeller shaft housing (counter rotation model) .................................... 6-35 removing the propeller shaft housing assembly..................................... 6-37 disassembling the propeller shaft housing.............................................. 6-37 ch...

  • Page 164

    Lowr lower unit 6-1 69j1d11 special service tools 6 slide hammer and adapters yb-06096 propeller shaft and bearing housing remover yb-06335 puller claw yb-06523 oil seal installer yb-06168, yb-06195 driver handle yb-06071 drive shaft needle bearing remover and installer yb-06196 needle bearing insta...

  • Page 165

    69j1d11 6-2 1 2 3 4 5 6 7 8 9 needle bearing installer yb-06434, yb-06435 pinion gear bushing installer yb-06029-4 needle bearing remover and installer yb-06213 taper roller bearing installer yb-06431 forward gear bearing cup installer yb-06276-b pinion shimming gauge iii yb-06441 shimming gauge i y...

  • Page 166

    Lowr lower unit 6-3 69j1d11 magnetic plate yb-07003 dial gauge yu-03097 magnetic flexible stand yu-34481 ring nut wrench yb-06578 puller bolt yb-41707 shimming gauge yb-06440-a.

  • Page 167

    69j1d11 6-4 1 2 3 4 5 6 7 8 9 lower unit (regular rotation model) 6 no. Part name q’ty remarks 1 lower unit 1 2 plate 1 3 rubber seal 1 4 check screw 1 5 gasket 2 not reusable 6 dowel pin 2 7 bolt 7 m10 × 45 mm 8 drain screw 1 9 grommet 1 10 bolt 1 m10 × 44 mm 11 bolt 1 m10 × 70 mm 12 spacer 1 13 wa...

  • Page 168

    Lowr lower unit 6-5 69j1d11 s69j6010u a a a a 11 12 13 14 15 16 17 18 20 19 21 22 23 24 24 9 10 1 4 5 6 lt 572 aa a a a a 8 3 2 7 lt 572 4.

  • Page 169

    69j1d11 6-6 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 shift rod 1 2 oil seal 1 not reusable 3 oil seal housing 1 4 o-ring 1 not reusable 3.1 × 70.6 mm 5 spring 1 6 circlip 1 7 bolt 3 m6 × 20 mm 8 seal 1 9 woodruff key 1 10 bolt 4 m8 × 45 mm 11 cover 1 12 seal 1 13 water pump housing 1 14 o-ring...

  • Page 170

    Lowr lower unit 6-7 69j1d11 removing the lower unit 1. Drain the gear oil. For draining proce- dures, see chapter 3, “changing the gear oil.” 2. Set the gearshift to the neutral position, and place a block of wood between the anti-cavitation plate and propeller to keep the propeller from turning, an...

  • Page 171

    69j1d11 6-8 1 2 3 4 5 6 7 8 9 checking the water pump and shift rod 1. Check the water pump housing for defor- mation. Replace if necessary. 2. Check the impeller 1 and insert car- tridge 2 for cracks or wear. Replace if necessary. 3. Check the woodruff key 3 and the groove a on the drive shaft for ...

  • Page 172

    Lowr lower unit 6-9 69j1d11 propeller shaft housing (regular rotation model) 6.

  • Page 173

    69j1d11 6-10 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 shift rod joint 1 2 ball 2 3 slider 1 4 shift plunger 1 5 dog clutch 1 6 cross pin 1 7 spring 1 8 propeller shaft 1 9 washer 1 10 reverse gear 1 11 reverse gear shim — as required 12 ball bearing 1 not reusable 13 o-ring 1 not reusable 3.1 ...

  • Page 174

    Lowr lower unit 6-11 69j1d11 removing the propeller shaft housing assembly 1. Remove the bolts 1, ring 2, and bolts 3. 2. Pull out the propeller shaft housing assembly. Disassembling the propeller shaft assembly 1. Remove the spring 1, and then remove the cross pin 2, dog clutch 3, slider 4, shift p...

  • Page 175

    69j1d11 6-12 1 2 3 4 5 6 7 8 9 3. Remove the oil seals and needle bear- ing. Checking the propeller shaft housing 1. Clean the propeller shaft housing using a soft brush and cleaning solvent, and then check it for cracks or damage. Replace if necessary. 2. Check the teeth and dogs of the reverse gea...

  • Page 176

    Lowr lower unit 6-13 69j1d11 assembling the propeller shaft assembly 1. Install the dog clutch 1 as shown. Note: install the dog clutch 1 with the “f” mark a facing toward the shift plunger. Assembling the propeller shaft housing 1. Install the needle bearing into the propel- ler shaft housing to th...

  • Page 177

    69j1d11 6-14 1 2 3 4 5 6 7 8 9 4. Install the reverse gear 7 and original shim(s) 8 to the propeller shaft housing using a press. Caution: add or remove shim(s), if necessary, when replacing the reverse gear or ball bearing. Bearing outer race attachment 9: yb-06109 È propeller shaft housing (regula...

  • Page 178

    Lowr lower unit 6-15 69j1d11 drive shaft and lower case (regular rotation model) 6.

  • Page 179

    69j1d11 6-16 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 drive shaft 1 2 cover 1 3 oil seal 2 not reusable 4 bolt 4 m8 × 25 mm 5 drive shaft housing 1 6 needle bearing 1 7 o-ring 1 not reusable 3 × 60.5 mm 8 pinion shim — as required 9 thrust bearing 1 10 lower case 1 11 needle bearing outer case...

  • Page 180

    Lowr lower unit 6-17 69j1d11 removing the drive shaft 1. Remove the drive shaft, drive shaft hous- ing, and pinion, and then pull out the for- ward gear. Disassembling the drive shaft housing 1. Remove the cover, oil seals, and needle bearing. Disassembling the forward gear 1. Remove the taper rolle...

  • Page 181

    69j1d11 6-18 1 2 3 4 5 6 7 8 9 checking the pinion and forward gear 1. Check the teeth of the pinion, and the teeth and dogs of the forward gear for cracks or wear. Replace if necessary. Checking the bearings 1. Check the bearings for pitting or rum- bling. Replace if necessary. Checking the drive s...

  • Page 182

    Lowr lower unit 6-19 69j1d11 2. Install the needle bearing outer case into the lower case. Note: apply engine oil to the needle bearing outer case before installation. 3. Install the needle bearing into the needle bearing outer case. Note: apply engine oil or grease to the needle bearing, and then i...

  • Page 183

    69j1d11 6-20 1 2 3 4 5 6 7 8 9 2. Install the drive shaft housing 1, thrust bearing 2, and original shim(s) 3 to the drive shaft 4. Caution: add or remove shim(s), if necessary, when replacing the drive shaft housing or drive shaft. 3. Install the drive shaft and drive shaft housing to the lower cas...

  • Page 184

    Lowr lower unit 6-21 69j1d11 2. Install the new gasket 2, outer plate car- tridge 3, and dowel pins 4. 3. Install the woodruff key into the drive shaft. 4. Align the groove on the impeller 5 with the woodruff key 6, and then install it to the drive shaft. 5. Install the washers 7, wave washer 8, spa...

  • Page 185

    69j1d11 6-22 1 2 3 4 5 6 7 8 9 7. Install the o-ring d and pump housing assembly e into the lower case, tighten the bolts f, and then install the seal g and cover h. Note: • when installing the pump housing, apply grease to the inside of the housing, and then turn the drive shaft clockwise while pus...

  • Page 186

    Lowr lower unit 6-23 69j1d11 5. Install the propeller and propeller nut, and then tighten the nut finger tight. Place a block of wood between the anti- cavitation plate and propeller to keep the propeller from turning, and then tighten the nut to the specified torque. Warning do not hold the propell...

  • Page 187

    69j1d11 6-24 1 2 3 4 5 6 7 8 9 shimming (regular rotation model) 6 a b f r p s69j6550 b4 t3 b3 65.0 t1 b1 39.4 41.0 t2 b2 b5 a1 a2 a3 drive shaft and lower case (regular rotation model) / shimming (regular rotation model).

  • Page 188

    Lowr lower unit 6-25 69j1d11 shimming note: • shimming is not required when assembling the original lower case and inner parts. • shimming is required when assembling the original inner parts and a new lower case. • shimming is required when replacing the inner part(s). Selecting the pinion shims 1....

  • Page 189

    69j1d11 6-26 1 2 3 4 5 6 7 8 9 selecting the forward gear shims 1. Calculate the specified value (m0) as shown in the examples below. Note: “f” is the deviation of the lower case dimen- sion from standard. The “f” mark a is stamped on the trim tab mounting surface of the lower case in 0.01 mm units....

  • Page 190

    Lowr lower unit 6-27 69j1d11 selecting the reverse gear shims 1. Calculate the specified value (m0) as shown in the examples below. Note: “r” is the deviation of the lower case dimen- sion from standard. The “r” mark a is stamped on the trim tab mounting surface of the lower case in 0.01 mm units. I...

  • Page 191

    69j1d11 6-28 1 2 3 4 5 6 7 8 9 backlash (regular rotation model) 6 measuring the forward and reverse gear backlash 1. Remove the water pump assembly. 2. Set the gearshift to the neutral position. 3. Install the special service tool so that it pushes against the propeller shaft. Note: tighten the uni...

  • Page 192

    Lowr lower unit 6-29 69j1d11 8. Remove the special service tools from the propeller shaft. 9. Apply a load to the reverse gear by installing the propeller 7, the spacer 8 (without the washer 9), then the washer 0 as shown. Note: tighten the propeller nut a while turning the drive shaft until the dri...

  • Page 193

    69j1d11 6-30 1 2 3 4 5 6 7 8 9 lower unit (counter rotation model) 6 no. Part name q’ty remarks 1 lower unit 1 2 plate 1 3 rubber seal 1 4 check screw 1 5 gasket 2 not reusable 6 dowel pin 2 7 bolt 7 m10 × 45 mm 8 drain screw 1 9 grommet 1 10 bolt 1 m10 × 44 mm 11 bolt 1 m10 × 70 mm 12 spacer 1 13 w...

  • Page 194

    Lowr lower unit 6-31 69j1d11.

  • Page 195

    69j1d11 6-32 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 shift rod 1 2 oil seal 1 not reusable 3 oil seal housing 1 4 o-ring 1 not reusable 3.1 × 70.6 mm 5 spring 1 6 circlip 1 7 bolt 3 m6 × 20 mm 8 seal 1 9 woodruff key 1 10 bolt 4 m8 × 45 mm 11 cover 1 12 seal 1 13 water pump housing 1 14 o-rin...

  • Page 196

    Lowr lower unit 6-33 69j1d11 removing the lower unit 1. Drain the gear oil. For draining proce- dures, see chapter 3, “changing the gear oil.” 2. Set the gearshift to the neutral position, and place a block of wood between the anti-cavitation plate and propeller to keep the propeller from turning, a...

  • Page 197

    69j1d11 6-34 1 2 3 4 5 6 7 8 9 checking the water pump and shift rod 1. Check the water pump housing for defor- mation. Replace if necessary. 2. Check the impeller 1 and insert car- tridge 2 for cracks or wear. Replace if necessary. 3. Check the woodruff key 3 and the groove a on the drive shaft for...

  • Page 198

    Lowr lower unit 6-35 69j1d11 propeller shaft housing (counter rotation model) 6.

  • Page 199

    69j1d11 6-36 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 shift rod joint 1 2 ball 2 3 slider 1 4 shift plunger 1 5 dog clutch 1 6 cross pin 1 7 spring 1 8 forward gear 1 9 forward gear shim — as required 10 ring nut 1 11 claw washer 1 12 bearing outer race 1 not reusable 13 taper roller bearing 1...

  • Page 200

    Lowr lower unit 6-37 69j1d11 removing the propeller shaft housing assembly 1. Remove the bolts 1, ring 2, and bolts 3. 2. Pull out the propeller shaft housing assembly. Disassembling the propeller shaft housing 1. Remove the spring 1, and then remove the cross pin 2, dog clutch 3, slider shift plung...

  • Page 201

    69j1d11 6-38 1 2 3 4 5 6 7 8 9 caution: • do not press the propeller shaft threads a directly. • do not reuse the taper roller bearing, always replace it with a new one. 6. Remove the oil seals and needle bear- ing. Checking the propeller shaft housing 1. Clean the propeller shaft housing using a so...

  • Page 202

    Lowr lower unit 6-39 69j1d11 2. Check the dog clutch, shift rod joint, and shift slider for cracks or wear. Replace if necessary. Assembling the propeller shaft housing 1. Install the needle bearing into the propel- ler shaft housing to the specified depth. Note: install the needle bearing with the ...

  • Page 203

    69j1d11 6-40 1 2 3 4 5 6 7 8 9 5. Install the propeller shaft assembly in the reverse direction into the lower case. 6. Install the ring nut 0 and claw washer a, and then tighten the ring nut to the specified torque. 7. Install the forward gear b, original shim(s) c, and dog clutch d using a press. ...

  • Page 204

    Lowr lower unit 6-41 69j1d11 drive shaft and lower case (counter rotation model) 6.

  • Page 205

    69j1d11 6-42 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 drive shaft 1 2 cover 1 3 oil seal 2 not reusable 4 bolt 4 m8 × 25 mm 5 drive shaft housing 1 6 needle bearing 1 7 o-ring 1 not reusable 3 × 60.5 mm 8 pinion shim — as required 9 thrust bearing 1 10 lower case 1 11 needle bearing case 1 12 ...

  • Page 206

    Lowr lower unit 6-43 69j1d11 removing the drive shaft 1. Remove the drive shaft assembly and pinion, and then pull out the reverse gear and thrust bearing. Disassembling the drive shaft housing 1. Remove the cover, oil seals, and needle bearing. Disassembling the reverse gear 1. Remove the needle be...

  • Page 207

    69j1d11 6-44 1 2 3 4 5 6 7 8 9 checking the pinion and reverse gear 1. Check the teeth of the pinion, and the teeth and dogs of the reverse gear for cracks or wear. Replace if necessary. Checking the bearings 1. Check the bearings for pitting or rum- bling. Replace if necessary. Checking the drive s...

  • Page 208

    Lowr lower unit 6-45 69j1d11 caution: add or remove shim(s), if necessary, when replacing the forward gear or lower case. 3. Install the needle bearing outer case into the lower case. Note: apply engine oil to the needle bearing outer case before installation. 4. Install the needle bearing into the ...

  • Page 209

    69j1d11 6-46 1 2 3 4 5 6 7 8 9 2. Apply grease to the new oil seals, and then install them into the drive shaft housing to the specified depth. Note: install an oil seal halfway into the drive shaft housing, then the other oil seal. Installing the drive shaft 1. Install the forward gear to the lower...

  • Page 210

    Lowr lower unit 6-47 69j1d11 note: apply grease to the new o-rings before installation. 2. Install the bolts 1, ring 2, and bolts 3, and then tighten the bolts 1 to the speci- fied torque. Installing the water pump and shift rod 1. Install the shift rod assembly 1. 2. Install the new gasket 2, outer...

  • Page 211

    69j1d11 6-48 1 2 3 4 5 6 7 8 9 5. Install the washers 7, wave washer 8, spacer 9, and collar 0 to the drive shaft. Note: • the collar and spacer should fit together firmly. • while pulling the drive shaft up, install the collar with an appropriate tool a that fits over the drive shaft as shown. 6. I...

  • Page 212

    Lowr lower unit 6-49 69j1d11 2. Install the two dowel pins 1 to the lower unit. 3. Install the lower unit to the upper case, and then tighten the bolts 2 to the speci- fied torque. 4. Install the trim tab 3 to its original posi- tion, and then tighten the bolt 4 to the specified torque. 5. Install t...

  • Page 213

    69j1d11 6-50 1 2 3 4 5 6 7 8 9 shimming (counter rotation model) 6 a b f r p s69j6670 b4 t3 b3 65.0 a3 t1 b1 38.4 a1 t2 b8 b5 a5 a4 a2 t´4 b7 b6 47.5 drive shaft and lower case (counter rotation model) / shimming (counter rotation model).

  • Page 214

    Lowr lower unit 6-51 69j1d11 shimming note: • shimming is not required when assembling the original lower case and inner parts. • shimming is required when assembling the original inner parts and a new lower case. • shimming is required when replacing the inner part(s). Selecting the pinion shims 1....

  • Page 215

    69j1d11 6-52 1 2 3 4 5 6 7 8 9 selecting the reverse gear shims 1. Calculate the specified value (m0) as shown in the examples below. Note: “f” is the deviation of the lower case dimen- sion from standard. The “f” mark a is stamped on the trim tab mounting surface of the lower case in 0.01 mm units....

  • Page 216

    Lowr lower unit 6-53 69j1d11 note: “r” is the deviation of the lower case dimen- sion from standard. The “r” mark a is stamped on the trim tab mounting surface of the lower case in 0.01 mm units. If the “r” mark is unreadable, assume that “r” is zero and check the backlash when the unit is assembled...

  • Page 217

    69j1d11 6-54 1 2 3 4 5 6 7 8 9 selecting the propeller shaft shims 1. Install the shim(s) 1, thrust bearing 2, propeller shaft 3, taper roller bearing 4, and claw washer 5, and then tighten the ring nut 6 to the specified torque. 2. Measure the propeller shaft free play as shown. 3. Select the prope...

  • Page 218

    Lowr lower unit 6-55 69j1d11 3. Install the special service tool so that it pushes against the propeller shaft. Note: tighten the universal puller or center bolt while turning the drive shaft until the drive shaft can no longer be turned. 4. Install the backlash indicator onto the drive shaft (22.4 ...

  • Page 219

    69j1d11 6-56 1 2 3 4 5 6 7 8 9 9. Turn the shift rod into the reverse posi- tion c with the shift rod push arm. 10. Turn the drive shaft clockwise until the dog clutch 7 is fully engaged. 11. Turn the shift rod to the neutral position d with the shift rod push arm. 12. Turn the drive shaft countercl...

  • Page 220: Bracket Unit

    Brkt 69j1d11 bracket unit special service tools ..................................................................................... 7-1 bottom cowling .............................................................................................. 7-3 upper case, steering arm, swivel bracket and cla...

  • Page 221

    69j1d11 1 2 3 4 5 6 7 8 9 power trim and tilt electrical system.......................................................... 7-43 checking the fuse.................................................................................... 7-44 checking the power trim and tilt relay ..............................

  • Page 222

    Brkt bracket unit 7-1 69j1d11 special service tools 7 ptt oil pressure gauge assembly yb-06580 ptt oil pressure gauge adapter yb-06581 trim and tilt cylinder wrench yb-06175-2b ptt piston vice attachment yb-06572 tilt rod wrench yb-06569.

  • Page 223: — Memo —

    69j1d11 7-2 1 2 3 4 5 6 7 8 9 — memo — special service tools.

  • Page 224

    Brkt bracket unit 7-3 69j1d11 bottom cowling 7.

  • Page 225

    69j1d11 7-4 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 bracket 1 2 shift cut switch 1 3 bracket 1 4 neutral switch 1 5 screw 2 m4 × 16 mm 6 plate 1 7 spring 1 8 bushing 2 9 grease nipple 1 10 bolt 1 11 bolt 1 m6 × 35 mm 12 clamp 1 13 bolt 1 m6 × 35 mm 14 screw 2 m4 × 16 mm 15 plate 1 16 clip 2 1...

  • Page 226

    Brkt bracket unit 7-5 69j1d11.

  • Page 227

    69j1d11 7-6 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 bottom cowling 1 2 rubber seal 1 3 cowling lock lever 2 4 bushing 6 5 plate 2 6 bolt 6 m6 × 30 mm 7 wave washer 3 8 lever 2 9 washer 3 10 bolt 3 m6 × 20 mm 11 spring 3 12 hook 3 13 bolt 3 m6 × 20 mm 14 bracket 1 15 bolt 2 m6 × 25 mm 16 plate...

  • Page 228

    Brkt bracket unit 7-7 69j1d11 upper case, steering arm, swivel bracket and clamp brackets 7.

  • Page 229

    69j1d11 7-8 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 upper case assembly 1 2 damper 2 3 bolt 2 m14 × 190 mm 4 washer 6 5 upper mount 2 6 bracket 1 7 bolt 3 m10 × 40 mm 8 bolt 4 m10 × 40 mm 9 mount housing 2 10 bolt 2 m14 × 205 mm 11 washer 2 12 rubber washer 2 13 lower mount 2 14 washer 2 15 d...

  • Page 230

    Brkt bracket unit 7-9 69j1d11.

  • Page 231

    69j1d11 7-10 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 upper exhaust guide 1 2 bolt 2 m8 × 35 mm 3 pressure control valve 1 4 bolt 1 m6 × 20 mm 5 plate 1 6 collar 1 7 bolt 7 m10 × 45 mm 8 gasket 1 not reusable 9 dowel pin 2 10 lower exhaust guide 1 11 gasket 1 not reusable 12 oil strainer 1 13 ...

  • Page 232

    Brkt bracket unit 7-11 69j1d11.

  • Page 233

    69j1d11 7-12 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 through tube 1 2 port clamp bracket 1 3 bolt 8 m10 × 45 mm 4 ground lead 3 5 screw 1 6 washer 2 7 bushing 10 8 friction plate 2 9 screw 4 m6 × 10 mm 10 screw 2 m6 × 15 mm 11 trim sensor 1 12 grease nipple 6 13 screw 1 m6 × 12 mm 14 clamp 2 ...

  • Page 234

    Brkt bracket unit 7-13 69j1d11 draining the engine oil 1. Place a drain pan under the drain hole, and then remove the drain bolt 1 and let the oil drain completely. 2. Remove the cover 2 and damper 3. 3. Remove the upper and lower mounting nut, and then remove the upper case. 4. Remove the muffler a...

  • Page 235

    69j1d11 7-14 1 2 3 4 5 6 7 8 9 2. Install the oil strainer 4 and bolts, and then tighten the bolts to the specified torque. 3. Install the oil pan 5, and then tighten the bolts finger tight. 4. Install the exhaust manifold 6 and bolts, and then tighten the bolts finger tight. 5. Tighten the exhaust ...

  • Page 236

    Brkt bracket unit 7-15 69j1d11 11. Install the upper mounts g and bolts into the upper case. 12. Install the bracket h, and then tighten the bolts to the specified torque. 13. Install the lower mounts i and mount housings j. Removing the steering arm 1. Remove the circlip 1. 2. Remove the steering y...

  • Page 237

    69j1d11 7-16 1 2 3 4 5 6 7 8 9 installing the steering arm 1. Install the washer 1 and bushing 2 onto the steering arm 3. 2. Place the swivel bracket 4 in an upright position, and then install the steering arm onto the swivel bracket. 3. Install the bushing 5, o-ring 6, bushing 7, and washer 8 onto ...

  • Page 238

    Brkt bracket unit 7-17 69j1d11 installing the upper case 1. Install the upper and lower mounting bolts into the swivel bracket 1 simulta- neously. 2. Install the upper mounting nut 2 and lower mounting nut 3, and then tighten them to the specified torques. Removing the power trim and tilt unit 1. Fu...

  • Page 239

    69j1d11 7-18 1 2 3 4 5 6 7 8 9 removing the clamp brackets 1. Remove the self-locking nut 1 and ground lead 2, then clamp brackets 3 and 4. 2. Remove the trim sensor 5. Installing the clamp brackets 1. Install the trim sensor 1 onto the port clamp bracket. Note: adjust the trim sensor after installi...

  • Page 240

    Brkt bracket unit 7-19 69j1d11 3. Install the tilt ram upper end into the swivel bracket with the shaft 4 and cir- clip 5. 4. Tighten the self-locking nut 6 to the specified torque. 5. Remove the anode 7. 6. Inject grease into all grease nipples until grease comes out from the bushings a. Adjusting ...

  • Page 241

    69j1d11 7-20 1 2 3 4 5 6 7 8 9 7. Fully tilt the outboard motor up, and then support it with the tilt stop lever. Warning after tilting up the outboard motor, be sure to support it with the tilt stop lever. Otherwise, the outboard motor could sud- denly lower if the power trim and tilt unit should l...

  • Page 242

    Brkt bracket unit 7-21 69j1d11 power trim and tilt unit 7.

  • Page 243

    69j1d11 7-22 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 cylinder block 1 2 reservoir 1 3 bolt 3 m8 × 20 mm 4 o-ring 1 not reusable 1.9 × 12.6 mm 5 reservoir cap 1 m12 × 10 mm 6 o-ring 1 not reusable 7 sheet 1 8 filter 1 9 spacer 1 10 bolt 3 m8 × 20 mm 11 o-ring 1 not reusable 2.4 × 22.6 mm 12 jo...

  • Page 244

    Brkt bracket unit 7-23 69j1d11.

  • Page 245

    69j1d11 7-24 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 circlip 2 2 dust seal 2 not reusable 3 trim cylinder end screw 2 4 o-ring 2 not reusable 5 trim ram 2 6 trim piston 2 7 washer 2 8 bolt 2 m8 × 20 mm 9 backup ring 2 10 o-ring 2 not reusable 11 spring 2 12 adapter 2 13 circlip 2 14 tilt ram ...

  • Page 246

    Brkt bracket unit 7-25 69j1d11.

  • Page 247

    69j1d11 7-26 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 gear housing 1 1 2 bolt 3 m5 × 40 mm 3 plate 1 4 filter 1 5 valve lock screw 2 6 down-relief spring 1 7 valve support pin 1 8 relief valve seal 1 9 up-relief spring 1 10 valve support pin 1 11 o-ring 1 not reusable 1.8 × 11.35 mm 12 ball 1 ...

  • Page 248

    Brkt bracket unit 7-27 69j1d11 disassembling the power trim and tilt motor 1. Remove the ptt motor screws 1, then the yoke 2. Caution: do not allow grease or oil to contact the commutator. Note: place a clean cloth over the end of the arma- ture shaft and carefully pull the armature from the yoke wi...

  • Page 249

    69j1d11 7-28 1 2 3 4 5 6 7 8 9 5. Check the circuit breaker for continuity. Replace the brush holder if there is no continuity. 6. Measure the brush length. Replace if out of specification. 7. Check the base for corrosion or damage. Replace if necessary. 8. Check the bearing for damage or wear. Repl...

  • Page 250

    Brkt bracket unit 7-29 69j1d11 6. Install the wave washer a and washer b into the yoke c. 7. Install the new o-ring and yoke c to the motor base. Note: place a clean cloth over the end of the arma- ture shaft and carefully push the armature from the yoke with a pair of pliers as shown. Checking the ...

  • Page 251

    69j1d11 7-30 1 2 3 4 5 6 7 8 9 6. Reverse the ptt motor leads between the battery terminals to fully extend the trim and tilt rams. 7. Remove the ptt oil pressure gauge adapter set 2. 8. Install the pipe joints 1, and then tight- ening them to the specified torque. 9. Connect the ptt motor leads to ...

  • Page 252

    Brkt bracket unit 7-31 69j1d11 14. Remove the ptt oil pressure gauge adapter set 2. 15. Install the pipe joints 3, and then tight- ening them to the specified torque. 16. After measuring the hydraulic pressure, connect the ptt motor leads to the bat- tery terminals to fully extend the trim and tilt ...

  • Page 253

    69j1d11 7-32 1 2 3 4 5 6 7 8 9 3. Remove the bracket 5, then the balls 6. 4. Remove the gear housing 2 7, then the shuttle pistons 8. 5. Remove the drive gear 9, balls 0, and dowel pins a. Disassembling the tilt cylinder and trim cylinders 1. Hold the tilt cylinder 1 in a vise using aluminum plates ...

  • Page 254

    Brkt bracket unit 7-33 69j1d11 warning never look into the tilt cylinder opening because the free piston and power trim and tilt fluid may be expelled out force- fully. 5. Hold the tilt piston in a vise using the special service tool 4 on both sides. 6. Remove the tilt ram. 7. Hold the cylinder bloc...

  • Page 255

    69j1d11 7-34 1 2 3 4 5 6 7 8 9 checking the reservoir 1. Check the reservoir for cracks or corro- sion. Replace if necessary. Checking the tilt cylinder and trim cylinder 1. Check the power trim and tilt unit for cracks or corrosion. Replace if neces- sary. 2. Check the inner walls of the cylinder b...

  • Page 256

    Brkt bracket unit 7-35 69j1d11 2. Check the up-relief valve and down-relief valve for dirt or residue. Clean if neces- sary. 3. Check the main valves for dirt or residue. Clean if necessary. 4. Check the absorber valves for dirt or res- idue. Clean if necessary. Checking the filters 1. Check gear pu...

  • Page 257

    69j1d11 7-36 1 2 3 4 5 6 7 8 9 3. Install the balls 7, manual release spring 8, and bracket 9 by installing the bolts 0, then tightening them to the specified torque. 4. Install the relief valve seal a and ball b into the gear housing 1 5. 5. Install the filters c and gear pump d by installing the b...

  • Page 258

    Brkt bracket unit 7-37 69j1d11 2. Install the tilt cylinder end screw 6, spring 7, adapter 8, and tilt piston 9 to the tilt ram 5. 3. Hold the tilt piston in a vise using the special service tool a on both sides. 4. Tighten the tilt ram 0 to the specified torque. 5. Install the new o-ring c and back...

  • Page 259

    69j1d11 7-38 1 2 3 4 5 6 7 8 9 4. Install the new o-ring 3, backup ring 4, spring 5, adapter 6, and circlip 7 to the trim piston 1. 5. Install the new oil seal 8, circlip 9, and new o-ring 0 into the trim cylinder end screw a. 6. Install the trim cylinder end screw a into the trim ram 2. Installing ...

  • Page 260

    Brkt bracket unit 7-39 69j1d11 3. Install the trim piston assembly into the trim cylinder, and then tighten the trim cylinder end screw 2 to the specified torque. Warning do not push the trim rams down while installing them into the trim cylinders. Otherwise, the power trim and tilt fluid may spurt ...

  • Page 261

    69j1d11 7-40 1 2 3 4 5 6 7 8 9 note: align the armature shaft with the recess in the joint. Installing the reservoir 1. Install the spacer 1, filter 2 and sheet 3 to the cylinder block. 2. Install the new o-ring 4 and reservoir 5, and then tighten the bolts 6 to the specified torque. 3. Install the ...

  • Page 262

    Brkt bracket unit 7-41 69j1d11 warning to prevent the power trim and tilt fluid from spurting out due to internal pres- sure, the tilt ram should be kept at full length. Note: place the tilt cylinder end screw at the bottom of the tilt ram and install the tilt piston assem- bly into the tilt cylinde...

  • Page 263

    69j1d11 7-42 1 2 3 4 5 6 7 8 9 note: • repeat this procedure so that the rams go up and down four to five times (be sure to wait a few seconds before switching the leads). • the sound of the power trim and tilt motor will change when the rams are fully extended. • if the rams do not move up and down...

  • Page 264

    Brkt bracket unit 7-43 69j1d11 power trim and tilt electrical system 7 1 fuse (30 a) 2 fuse (20 a) 3 power trim and tilt relay 4 power trim and tilt motor 5 10-pin coupler 6 battery 7 power trim and tilt switch 8 trim sensor b : black lg : light green p : pink r : red sb : sky blue s69j7520u b p r r...

  • Page 265

    69j1d11 7-44 1 2 3 4 5 6 7 8 9 checking the fuse 1. Check the fuse for continuity. Replace if there is no continuity. Checking the power trim and tilt relay 1. Check the power trim and tilt relay for continuity. Replace if out of specification. Note: be sure to set the measurement range a shown in t...

  • Page 266

    Brkt bracket unit 7-45 69j1d11 checking the power trim and tilt switch 1. Check the power trim and tilt switch for continuity. Replace if out of specification. Checking the trim sensor 1. Measure the trim sensor resistance. Replace if out of specification. Note: turn the lever 1 and measure the resi...

  • Page 267: Electrical Systems

    69j1d11 elec – + 1 2 3 4 5 6 7 8 9 electrical systems special service tools ..................................................................................... 8-1 checking the electrical components............................................................ 8-2 measuring the peak voltage ...........

  • Page 268

    Elec electrical systems – + 8-1 69j1d11 special service tools 8 dynamic spark tester ym-34487 digital multimeter yu-34899-a peak voltage adaptor yu-39991 test harness (2 pins) yb-06792 test harness (4 pins) yb-06771 test harness (3 pins) yb-06793 test harness (3 pins) yb-06770 test harness (2 pins) ...

  • Page 269

    69j1d11 8-2 1 2 3 4 5 6 7 8 9 checking the electrical components 8 measuring the peak voltage note: before troubleshooting the peak voltage, check that all electrical connections are tight and free from corrosion, and that the battery is fully charged to 12 v. The condition of the ignition system ca...

  • Page 270

    Elec electrical systems – + 8-3 69j1d11 electrical components 8 starboard and rear views 1 thermoswitch 2 starter motor 3 oil pressure sensor 4 ignition coils s69j8030 #1 #3 #5 #2 #4 #6.

  • Page 271

    69j1d11 8-4 1 2 3 4 5 6 7 8 9 port view 1 fuel injectors 2 fuel pump driver and isolator 3 low-pressure fuel pump 4 ecm 5 high-pressure fuel pump 6 fuses s69j8040u 6 6 5 4 3 1 2 electrical components.

  • Page 272

    Elec electrical systems – + 8-5 69j1d11 front view 1 starter motor 2 fuses 3 ecm 4 main relay 5 rectifier regulator 6 power trim and tilt relay 7 starter relay s69j8050u e e.

  • Page 273

    69j1d11 8-6 1 2 3 4 5 6 7 8 9 top view 1 spark plugs 2 idle speed control 3 thermoswitches 4 intake air pressure sensor 5 engine temperature sensor 6 fuses 7 rectifier regulator 8 intake air temperature sensor 9 starter motor 0 oil pressure sensor a stator coil b throttle position sensor c ignition ...

  • Page 274

    Elec electrical systems – + 8-7 69j1d11 wiring harness 8 l/y r/y o/b b b br r/y o/r p p b o b r/y o/y r/y o/b b/o r/y p p b b/y r/y b/w o b p /g r/y r/y o/r r/y b l l b/w r/y r/y l/r r/y l/w o/y g g/y g/r r/y r/y r/y r/y g/b l/w r/y r/y r/y r/y r/y r/y r/y r/y r/y r/y r/y r/y r/y r/y r/b r/y b b b b...

  • Page 275

    69j1d11 8-8 1 2 3 4 5 6 7 8 9 connect to: 1 neutral switch 2 shift cut switch 3 fuel injector 4 throttle position sensor 5 thermoswitch 6 ignition coil 7 intake air pressure sensor 8 low-pressure fuel pump 9 trim meter 0 fuel pump driver and isolator a high-pressure fuel pump b idle speed control c ...

  • Page 276

    Elec electrical systems – + 8-9 69j1d11 connect to: 1 accessory battery 2 main relay 3 fuel pump driver and isolator 4 starter relay 5 power trim and tilt relay b : black br : brown g : green gy : gray l : blue lg : light green o : orange p : pink r : red sb : sky blue w : white y : yellow b/o : bla...

  • Page 277

    69j1d11 8-10 1 2 3 4 5 6 7 8 9 ignition and ignition control system 8 1 ecm 2 oil pressure sensor 3 intake air temperature sensor 4 engine temperature sensor 5 main relay 6 fuse (30 a) 7 fuse (20 a) 8 battery 9 pulser coil 0 stator coil a rectifier regulator b intake air pressure sensor c thermoswit...

  • Page 278

    Elec electrical systems – + 8-11 69j1d11 checking the ignition spark gap 1. Remove the ignition coil cover and dis- connect the spark plug caps from the spark plugs. 2. Connect a spark plug cap to the special service tool. 3. Crank the engine and observe the spark through the discharge window of the...

  • Page 279

    69j1d11 8-12 1 2 3 4 5 6 7 8 9 checking the ecm 1. Remove the ignition coil cover and dis- connect the ignition coil coupler. 2. Connect the test harness (2 pins) to the ignition coil. 3. Measure the ecm output peak voltage. If below specification, measure the pulser coil output peak voltage. Replac...

  • Page 280

    Elec electrical systems – + 8-13 69j1d11 checking the intake air temperature sensor 1. Place the intake air temperature sensor in a container of water and slowly heat the water. 2. Measure the intake air temperature sen- sor resistance. Replace if out of specifi- cation. Checking the engine temperat...

  • Page 281

    69j1d11 8-14 1 2 3 4 5 6 7 8 9 checking the thermoswitch 1. Place the thermoswitch in a container of water and slowly heat the water. 2. Check the switch for continuity at the specified temperatures. Replace if out of specification. A temperature b time c no continuity d continuity checking the shif...

  • Page 282

    Elec electrical systems – + 8-15 69j1d11 checking the main relay 1. Connect the digital circuit tester leads to main relay terminals 1, 2, and 3. 2. Connect the terminal 4 to the positive battery terminal. 3. Connect the terminal 5 to the negative battery terminal. 4. Check for continuity between th...

  • Page 283

    69j1d11 8-16 1 2 3 4 5 6 7 8 9 fuel control system 8 1 ecm 2 oil pressure sensor 3 intake air temperature sensor 4 engine temperature sensor 5 main relay 6 fuse (5 a) 7 fuse (30 a) 8 fuse (20 a) 9 battery 0 pulser coil a stator coil b rectifier regulator c intake air pressure sensor d thermoswitch e...

  • Page 284

    Elec electrical systems – + 8-17 69j1d11 8 b : black br : brown g : green l : blue o : orange p : pink r : red y : yellow b/w : black/white b/y : black/yellow g/b : green/black g/r : green/red g/w : green/white g/y : green/yellow l/r : blue/red l/y : blue/yellow o/b : orange/black o/r : orange/red o...

  • Page 285

    69j1d11 8-18 1 2 3 4 5 6 7 8 9 checking the low-pressure fuel pump and high-pressure fuel pump 1. Disconnect the starter relay lead (brown lead) 1 to prevent the engine from start- ing. 2. Turn the engine start switch to on. 3. Listen for the operating sound of the high-pressure fuel pump 2. Replace...

  • Page 286

    Elec electrical systems – + 8-19 69j1d11 starting system 8 1 fuse (30 a) 2 fuse (20 a) 3 starter relay 4 starter motor 5 battery b : black br : brown r : red br/w : brown/white s69j8330 r r b b b r br br/w br/w r b b r br br r r r r.

  • Page 287

    69j1d11 8-20 1 2 3 4 5 6 7 8 9 checking the fuse 1. Check the fuse for continuity. Replace if there is no continuity. Checking the wiring harness (10 pins) 1. Check the wiring harness for continuity. Replace if there is no continuity. Checking the starter relay 1. Connect the digital circuit tester ...

  • Page 288

    Elec electrical systems – + 8-21 69j1d11 starter motor 8.

  • Page 289

    69j1d11 8-22 1 2 3 4 5 6 7 8 9 no. Part name q’ty remarks 1 clip 1 2 pinion stopper 1 3 starter motor pinion 1 4 spring 1 5 bolt 2 m6 × 35 mm 6 housing 1 7 rubber seal 1 8 bearing 1 9 clutch assembly 1 10 e-clip 1 not reusable 11 thrust washer 1 12 center bracket 1 13 pinion shaft 1 14 planetary gea...

  • Page 290

    Elec electrical systems – + 8-23 69j1d11 removing the starter motor pinion 1. Slide the pinion stopper 1 down as shown, and then remove the clip 2. Note: remove the clip with a thin screwdriver. Checking the starter motor pinion 1. Check the teeth of the pinion for cracks or wear. Replace if necessa...

  • Page 291

    69j1d11 8-24 1 2 3 4 5 6 7 8 9 checking the brushes 1. Measure the brush length. Replace the brush assembly if out of specification. 2. Check the brush holder assembly for continuity. Replace if out of specifica- tions. Checking the magnet switch 1. Connect the tester leads between the magnet switch...

  • Page 292

    Elec electrical systems – + 8-25 69j1d11 charging system 8 1 stator coil 2 rectifier regulator 3 fuse (30 a) 4 starting battery 5 accessory battery 6 fuel pump driver and isolator b : black g : green r : red w : white y : yellow g/w : green/white r/y : red/yellow g g g g g g g/w g/w g/w g/w g/w g/w ...

  • Page 293

    69j1d11 8-26 1 2 3 4 5 6 7 8 9 checking the stator coil 1. Remove the intake silencer and discon- nect the stator coil coupler. 2. Connect the test harness (3 pins) to the stator coil. 3. Install the intake silencer. Caution: do not start the engine when the intake silencer is not installed. 4. Meas...

  • Page 294

    Elec electrical systems – + 8-27 69j1d11 digital multimeter: yu-34899-a peak voltage adaptor: yu-39991 test harness (2 pins): yb-06787 rectifier regulator output peak voltage: red (r) – black (b) red/yellow (r/y) – black (b) r/min unloaded 1,500 3,500 dc v 13 13.

  • Page 295: Troubleshooting

    69j1d11 trbl shtg 1 2 3 4 5 6 7 8 9 troubleshooting special service tools ..................................................................................... 9-1 yamaha diagnostic system .......................................................................... 9-2 introduction.......................

  • Page 296

    Trbl shtg troubleshooting 9-1 69j1d11 special service tools 9 yamaha diagnostic system 60v-85300-02 yamaha diagnostic system 60v-ws853-02 diagnostic test lead yb-06795 yamaha diagnostic system installation manual.

  • Page 297

    69j1d11 9-2 1 2 3 4 5 6 7 8 9 yamaha diagnostic system 9 introduction features the newly developed yamaha diagnostic system provides quicker detection and analysis of engine malfunctions for quicker troubleshooting procedures than traditional methods. By connecting your computer to the ecm (electron...

  • Page 298

    Trbl shtg troubleshooting 9-3 69j1d11 hardware requirements make sure that your computer meets the following requirements before using this software. Computer: ibm-compatible computer operating system: microsoft (windows 95,) windows 98, windows me, windows 2000, or windows xp (english version) cpu:...

  • Page 299

    69j1d11 9-4 1 2 3 4 5 6 7 8 9 connecting the communication cable to the outboard motor 3-pin communication coupler yamaha diagnostic system.

  • Page 300

    Trbl shtg troubleshooting 9-5 69j1d11 note: • to diagnose a mechanical malfunction, use the troubleshooting charts pertaining to the trouble located in this chapter. Also, when checking and maintaining the outboard motor, see chapters 4– 8 for safe maintenance procedures. • check that all electrical...

  • Page 301

    69j1d11 9-6 1 2 3 4 5 6 7 8 9 check the wiring harnesses for continuity. Replace the starter relay. Listen for the operation sound of the starter relay. Check the power unit. Can the oper- ation sound be heard? Yes yes no is there continuity? Replace the fuse. Yes no replace the engine stop lan- yar...

  • Page 302

    Trbl shtg troubleshooting 9-7 69j1d11 symptom: engine cranks, but will not start (engine stop lanyard switch is operating nor- mally). • check the ignition system. • check the fuel system. • check the compression pressure of the power unit. Wet spark plugs? Check the condition of the spark plugs. Wa...

  • Page 303

    69j1d11 9-8 1 2 3 4 5 6 7 8 9 does the engine start? Wet spark plugs? Out of specification? Out of specification? Failure in starting operation failure in starting operation check the fuel system. Check the condition of the spark plugs again. Check the compression pres- sure of the combustion chambe...

  • Page 304

    Trbl shtg troubleshooting 9-9 69j1d11 symptom: engine can be started, but does not remain on. • check the fuel system. • check the ignition system. • check the compression pressure of the power unit. Fuel system is the vent screw open? Water or residue? Kinks or fuel leakage? Check for water or resi...

  • Page 305

    69j1d11 9-10 1 2 3 4 5 6 7 8 9 ignition system compression pressure out of specification? Yes no out of specification? Yes out of specification? No yes check the ignition system using the yamaha diagnostic system. Replace the ignition coil. Check the ignition spark gap using the spark gap tester. Re...

  • Page 306

    Trbl shtg troubleshooting 9-11 69j1d11 symptom: the engine idle speed is not steady, but increases or decreases. • check the intake manifold. • check the air intake system. • check the ignition system. Out of specification? Are the throt- tle valves synchronize? Check the second- ary air intake on t...

  • Page 307

    69j1d11 9-12 1 2 3 4 5 6 7 8 9 symptom: engine does not accelerate when the throttle is opened quickly. The engine turns off when the throttle is opened quickly. Acceleration is tardy and the engine is likely to stop at any moment. • check the engine using the diagnostic flash indicator or the yamah...

  • Page 308

    Trbl shtg troubleshooting 9-13 69j1d11 lubrication system check the oil pump for debris or oil leaks. Check the engine oil level. Check the oil pressure. Check the oil pressure sensor. Clean or replace the respective parts. At specified level? Out of specification? Check the oil passage. Yes no yes ...

  • Page 309

    69j1d11 9-14 1 2 3 4 5 6 7 8 9 bracket unit 9 symptom: power trim and tilt unit does not operate. Listen for the operation sound of the power trim and tilt relay. Listen for the operation sound of the power trim and tilt motor. Check that the manual valve is closed. Check the power trim and tilt flu...

  • Page 310

    Trbl shtg troubleshooting 9-15 69j1d11 check the fluid passages for clogs or debris. Clean the passages. Check the internal parts (valves, pistons, gears, etc.). Clean or replace the filters. No yes no yes add fluid to the correct level. At specified level? Yes no disassemble the power trim and tilt...

  • Page 311

    69j1d11 9-16 1 2 3 4 5 6 7 8 9 symptom: power trim and tilt unit does not hold the outboard motor up. Check that the manual valve is closed. Check the power trim and tilt fluid level. Close the valve. Add fluid to the correct level. At specified level? Is it closed? Yes yes no no check the fluid pas...

  • Page 312

    Trbl shtg troubleshooting 9-17 69j1d11 symptom: shift mechanism of the forward gear and reverse gear does not operate properly. Check the operation of the shift rod. Check the condition of the shift rod connection between the lower case and upper case. Replace the shift rod. Check the shift cables a...

  • Page 313

    69j1d11 9-18 1 2 3 4 5 6 7 8 9 electrical systems 9 symptom: battery becomes weaker quickly. • check the charging system. Measure the rectifier regulator output peak voltage. Replace the stator coil. Out of specification? Out of specification? Replace the rectifier regulator. No no yes yes measure t...

  • Page 314

    Trbl shtg troubleshooting 9-19 69j1d11 self-diagnosis 9 diagnosing the electronic control system 1. Connect the special tools to the outboard motor as shown. Note: when performing this diagnosis, all of the electrical wires must be properly connected. 2. Start the engine and let it idle. 3. Check th...

  • Page 315

    69j1d11 9-20 1 2 3 4 5 6 7 8 9 code symptom 1 normal 13 incorrect pulser coil signal 15 incorrect engine temperature sensor signal 18 incorrect throttle position sensor signal 19 incorrect battery voltage 23 incorrect intake air temperature sensor signal 28 incorrect neutral switch signal 29 incorre...

  • Page 316

    Index i-1 60c5d11 a. Adjusting the throttle link and throttle cable operation (with a stop bolt) ............3-10 adjusting the throttle link and throttle cable operation (without a stop bolt) .......3-11 adjusting the trim sensor ..........................7-19 after test run ..........................

  • Page 317

    60c5d11 i-2 1 2 3 4 5 6 7 8 9 checking the piston clearance..................5-48 checking the piston diameter ...................5-47 checking the piston pin.............................5-50 checking the piston pin boss bore............5-49 checking the piston ring grooves..............5-49 checkin...

  • Page 318

    Index i-3 60c5d11 g. General .....................................................3-18 general specifications.................................2-1 general torques ........................................2-17 good working practices ..............................1-4 h. Hose routing........................

  • Page 319

    60c5d11 i-4 1 2 3 4 5 6 7 8 9 s. Safety while working ...................................1-3 selecting the connecting rod bearing........5-52 selecting the crankshaft main bearing ......5-54 selecting the forward gear shims.... 6-26 , 6-52 selecting the pinion shims .............. 6-25 , 6-51 select...

  • Page 320

    Wiring diagram f200tr, lf200tr, f225tr, lf225tr 1 low-pressure fuel pump 2 accessory battery 3 fuel pump driver and isolator 4 high-pressure fuel pump 5 idle speed control 6 fuel injector 7 spark plug 8 ignition coil 9 intake air pressure sensor 0 thermoswitch a engine temperature sensor b pulser co...

  • Page 321

    Yamaha motor corporation, usa printed in usa sep. 2003 – 0.0 × 1 cr (e).

  • Page 322

    L/y b b br f200tr, lf200tr, f225tr, lf225tr g/w g/w g/w g/w br/w br/w w/r w/r w/b w/b b/w w/g w/g g/w g/w b lg r sb g/w g/w g g g/w g g r/y l l b l/w r/y b r r/y r/y b r/y r/y r/y r/y r/y r/b b r/y r/y r/y b b w/b r/b b lg lg sb r/y r/y r/y r r r r r/y r/y g/b g/b g/b g/y g/y g/y g r/y r/y r/y r/y g...

  • Page 323

    4 5 9 g/r r/y l b l/r b/w r/y r/y r/y r/y r/y o/r o/y o/b r/y r/y r/y b/y p/w w/g w/b w/r b/y p/g r/y r/y o/r b/y r/y o/b r/y r/y o/y b/o r/y b/w l/y o/r o/y o/b y/g r/y r/y w/b l/w l/w p/b p/b p/b r/y g p p p b b p b b b b r 1 4 6 5 3 r b b b b b b o b p p b o p b b br b sb y g br r lg sb sb o lg l...