- DL manuals
- Yamaha
- Motorcycle
- FJR1300A
- Owner's Manual
Yamaha FJR1300A Owner's Manual
Summary of FJR1300A
Page 1
Dic183 fjr1300a owner’s manual read this manual carefully before operating this vehicle. 1mc-28199-e0 [english (e)].
Page 2
Eau50920 read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold. General manager of quality assurance div. Date of issue: 1 aug. 2002 place of issue: shizuoka, japan declaration of conformity yamaha motor electronics co., ltd. 1450-6, mori, ...
Page 3: Introduction
Introduction eau10102 welcome to the yamaha world of motorcycling! As the owner of the fjr1300a, you are benefiting from yamaha’s vast experience and newest technology regarding the design and manufacture of high-quality products, which have earned yamaha a reputation for dependability. Please take ...
Page 4: Important Manual Information
Important manual information eau10133 particularly important information is distinguished in this manual by the following notations: *product and specifications are subject to change without notice. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey a...
Page 5: Important Manual Information
Important manual information eau10200 fjr1300a owner’s manual ©2012 by yamaha motor co., ltd. 1st edition, june 2012 all rights reserved. Any reprinting or unauthorized use without the written permission of yamaha motor co., ltd. Is expressly prohibited. Printed in japan. U1mce0e0.Book page 2 thursd...
Page 6: Table Of Contents
Table of contents safety information ..................1-1 description ..................................2-1 left view ..........................................2-1 right view ........................................2-2 controls and instruments.................2-3 instrument and control functions .....
Page 7: Table of Contents
Table of contents checking and lubricating the brake and clutch levers .............6-27 checking and lubricating the centerstand and sidestand ........6-28 lubricating the rear suspension ...6-29 lubricating the swingarm pivots ...6-29 checking the front fork .................6-29 checking the stee...
Page 8: Safety Information
1-1 1 safety information eau1028a be a responsible owner as the vehicle’s owner, you are respon- sible for the safe and proper operation of your motorcycle. Motorcycles are single-track vehicles. Their safe use and operation are de- pendent upon the use of proper riding techniques as well as the exp...
Page 9: Safety Information
Safety information 1-2 1 ● many accidents involve inexperi- enced operators. In fact, many op- erators who have been involved in accidents do not even have a cur- rent motorcycle license. • make sure that you are qualified and that you only lend your mo- torcycle to other qualified opera- tors. • kn...
Page 10: Safety Information
Safety information 1-3 1 avoid carbon monoxide poisoning all engine exhaust contains carbon monoxide, a deadly gas. Breathing car- bon monoxide can cause headaches, dizziness, drowsiness, nausea, confu- sion, and eventually death. Carbon monoxide is a colorless, odor- less, tasteless gas which may b...
Page 11: Safety Information
Safety information 1-4 1 tents, can create unstable han- dling or a slow steering re- sponse. ● this vehicle is not designed to pull a trailer or to be attached to a sidecar. Genuine yamaha accessories choosing accessories for your vehicle is an important decision. Genuine yamaha accessories, which ...
Page 12: Safety Information
Safety information 1-5 1 tor and may limit control ability, therefore, such accessories are not recommended. ● use caution when adding electri- cal accessories. If electrical acces- sories exceed the capacity of the motorcycle’s electrical system, an electric failure could result, which could cause ...
Page 13: Description
Description 2-1 2 eau10410 left view 1 2 3 4 5 7 6 8 9 10 11 12 13 1. Coolant reservoir (page 6-16) 2. Accessory box (page 3-36) 3. Front fork spring preload adjusting bolt (page 3-39) 4. Owner’s tool kit (page 6-2) 5. Final gear oil filler bolt (page 6-14) 6. Final gear oil drain bolt (page 6-14) 7...
Page 14: Description
Description 2-2 2 eau10420 right view 8 9 10 11 6,7 5 3,4 2 1 1. Storage compartment (page 3-35) 2. Fuel tank cap (page 3-29) 3. Front fork spring preload adjusting bolt (page 3-39) 4. Front fork rebound damping force adjusting knob (page 3-39) 5. Windshield (page 3-12) 6. Fuses (page 6-32) 7. Batte...
Page 15: Description
Description 2-3 2 eau10430 controls and instruments 1 2 3 4 5 6 7 8 2 9 10,11 12 11 1. Clutch lever (page 3-25) 2. Rear view mirror (page 3-39) 3. Left handlebar switches (page 3-23) 4. Clutch fluid reservoir (page 6-24) 5. Multi-function meter unit (page 3-9) 6. Main switch/steering lock (page 3-2)...
Page 16
Instrument and control functions 3-1 3 eau10977 immobilizer system this vehicle is equipped with an immo- bilizer system to help prevent theft by re-registering codes in the standard keys. This system consists of the fol- lowing: ● a code re-registering key (with a red bow) ● two standard keys (with...
Page 17
Instrument and control functions 3-2 3 ● keep other immobilizer system keys away from the main switch as they may cause signal inter- ference. Eau10472 main switch/steering lock the main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various po...
Page 18
Instrument and control functions 3-3 3 to lock the steering 1. Turn the handlebars all the way to the left or right. 2. Push the key in from the “off” po- sition, and then turn it to “lock” while still pushing it. 3. Remove the key. To unlock the steering push the key into the main switch, and then ...
Page 19
Instrument and control functions 3-4 3 eau49392 indicator lights and warning lights eau11030 turn signal indicator lights “ ” and “ ” the corresponding indicator light flash- es when the turn signal switch is pushed to the left or right. Eau11060 neutral indicator light “ ” this indicator light come...
Page 20
Instrument and control functions 3-5 3 if the warning light does not come on initially when the key is turned to “on”, or if the warning light remains on, have a yamaha dealer check the electrical circuit. Eau51661 abs warning light “ ” in normal operation, the abs warning light comes on when the ke...
Page 21
Instrument and control functions 3-6 3 eau54680 immobilizer system indicator light “ ” the electrical circuit of the indicator light can be checked by turning the key to “on”. The indicator light should come on for a few seconds, and then go off. If the indicator light does not come on initially whe...
Page 22
Instrument and control functions 3-7 3 activating and setting the cruise control system 1. Push the cruise control power switch “ ” located on the left han- dlebar. The cruise control system indicator light “ ” will come on. 2. Push the “set–” side of the cruise control setting switch to activate th...
Page 23
Instrument and control functions 3-8 3 speed will return to the previously set cruising speed. The “set” indicator light will come on. Warning ewa16350 it is dangerous to use the resume function when the previously set cruising speed is too high for cur- rent conditions. Tip ● the resume function op...
Page 24
Instrument and control functions 3-9 3 speed, apply the brakes. When the brakes are applied, the cruise con- trol system will become deactivat- ed. Self-diagnosis device the cruise control system will also be- come deactivated when an irregularity with any of the vehicle systems is de- tected. The “...
Page 25
Instrument and control functions 3-10 3 settings while riding can distract the operator and increase the risk of an accident. Tip the select switch “ / ” and the menu switch “menu” are located on the left handlebar. These switches al- low you to control or change the set- tings of the multi-function...
Page 26
Instrument and control functions 3-11 3 fuel meter the fuel meter indicates the amount of fuel in the fuel tank. The display seg- ments of the fuel meter disappear to- wards “e” (empty) as the fuel level decreases. When the last segment starts flashing, refuel as soon as possi- ble. When the key is ...
Page 27
Instrument and control functions 3-12 3 drive mode display this display indicates which drive mode has been selected: touring mode “t” or sports mode “s”. For more details on the modes and on how to se- lect them, see pages 3-22 and 3-24. Function display push the menu switch “menu” to switch the di...
Page 28: 5.0
Instrument and control functions 3-13 3 ● if the handlebar grip or throttle grip becomes worn or damaged, stop using the grip warmers and replace the grips. Selecting the information display there are 3 information displays. The selected information display can be switched by pushing the select swit...
Page 29: 0:06
Instrument and control functions 3-14 3 trip-f → display–1 → display–2 → display–3 → trip-f to reset a tripmeter, use the select switch to select the information display that contains the tripmeter. Push the “reset” button briefly so that the trip- meter flashes, and then push the “re- set” button a...
Page 30: 12.3
Instrument and control functions 3-15 3 tip the selected information display can- not be switched while the message “hi” is flashing. Notice eca10021 do not continue to operate the en- gine if it is overheating. Average fuel consumption display: the average fuel consumption display modes “km/l”, “l/...
Page 31
Instrument and control functions 3-16 3 ● the “l/100km” display shows the amount of fuel necessary to travel 100 km. ● for the uk only: the “mpg” dis- play shows the distance that can be traveled on 1.0 imp.Gal of fuel. Tip if traveling at speeds under 10 km/h, “_ _._” will be displayed. Notice eca1...
Page 32
Instrument and control functions 3-17 3 adjusting the temperature levels of the grip warmer settings 1. Use the select switch to highlight “grip warmer”. 2. Push the menu switch “menu”. The grip warmer setting display will be shown and “high” will flash in the display. 3. Push the menu switch “menu”...
Page 33: 0:07
Instrument and control functions 3-18 3 2. Push the menu switch “menu”, and then push the “reset” button to select the item to reset. 3. While the selected item is flashing, push the “reset” button for at least 2 seconds. 4. Push the menu switch “menu” to return to the setting mode menu. Checking an...
Page 34
Instrument and control functions 3-19 3 tip ● for the uk: continue with the fol- lowing steps. ● except for the uk: skip steps 3–5. 3. Push the menu switch “menu”. “km” or “mile” will flash in the dis- play. 4. Use the select switch to select “km” or “mile”, and then push the menu switch “menu”. Tip...
Page 35
Instrument and control functions 3-20 3 3. Use the select switch to highlight the item to change, and then push the menu switch “menu”. 4. Use the select switch to select the item to show, and then push the menu switch “menu”. 5. When you are finished changing the settings, use the select switch to ...
Page 36: 5 55
Instrument and control functions 3-21 3 setting the clock 1. Use the select switch to highlight “clock”. 2. Push the menu switch “menu”. 3. When the hour digits start flashing, use the select switch to set the hours. 4. Push the menu switch “menu”, and the minute digits start flashing. 5. Use the se...
Page 37
Instrument and control functions 3-22 3 this model is equipped with a self-diag- nosis device for various electrical cir- cuits. If a problem is detected in any of those circuits, the engine trouble warn- ing light will come on and the informa- tion display will indicate an error code. If the inform...
Page 38
Instrument and control functions 3-23 3 this mode allows the rider to enjoy smooth drivability from the low-speed range to the high-speed range. Sports mode “s” this mode offers a sportier engine re- sponse in the low- to mid-speed range compared to the touring mode. Eau1234b handlebar switches left...
Page 39
Instrument and control functions 3-24 3 position. To cancel the turn signal lights, push the switch in after it has re- turned to the center position. Eau12500 horn switch “ ” press this switch to sound the horn. Eau54210 start/engine stop switch “ / / ” to crank the engine with the starter, set thi...
Page 40
Instrument and control functions 3-25 3 eau12830 clutch lever the clutch lever is located at the left handlebar grip. To disengage the clutch, pull the lever toward the handle- bar grip. To engage the clutch, release the lever. The lever should be pulled rapidly and released slowly for smooth clutch...
Page 41
Instrument and control functions 3-26 3 eau26824 brake lever the brake lever is located on the right side of the handlebar. To apply the front brake, pull the lever toward the throttle grip. The brake lever is equipped with a brake lever position adjusting dial. To adjust the distance between the br...
Page 42
Instrument and control functions 3-27 3 tip ● the abs performs a self-diagno- sis test each time the vehicle first starts off after the key is turned to “on” and the vehicle has traveled at a speed of 10 km/h (6 mi/h) or higher. During this test, a “clicking” noise can be heard from under the seat, ...
Page 43
Instrument and control functions 3-28 3 proach surfaces that may be slippery with caution and avoid es- pecially slippery surfaces. When the key is turned to “on”, the traction control system automatically turns on. The traction control system can be turned on or off manually only when the key is in...
Page 44
Instrument and control functions 3-29 3 to reset the traction control system turn the key to “off”. Wait at least 1 second, then turn the key back to “on”. The “tcs” indicator/warning light should go off and the system will be en- abled. The engine trouble warning light should go off after the motor...
Page 45
Instrument and control functions 3-30 3 eau13221 fuel make sure there is sufficient gasoline in the tank. Warning ewa10881 gasoline and gasoline vapors are extremely flammable. To avoid fires and explosions and to reduce the risk of injury when refueling, follow these instructions. 1. Before refueli...
Page 46
Instrument and control functions 3-31 3 eaub1300 fuel tank breather/overflow hose before operating the motorcycle: ● check the fuel tank breather/over- flow hose connection. ● check the fuel tank breather/over- flow hose for cracks or damage, and replace it if damaged. ● make sure that the end of th...
Page 47
Instrument and control functions 3-32 3 eau39495 seats passenger seat to remove the passenger seat 1. Insert the key into the seat lock, and then turn it counterclockwise. 2. Lift the front of the passenger seat and pull it forward. To install the passenger seat 1. Insert the projections on the rear...
Page 48
Instrument and control functions 3-33 3 2. Install the passenger seat. Tip ● make sure that the seats are prop- erly secured before riding. ● the rider seat height can be ad- justed to change the riding posi- tion. (see the following section.) eau39632 adjusting the rider seat height the rider seat ...
Page 49
Instrument and control functions 3-34 3 5. Insert the projection on the front of the rider seat into seat holder b as shown. 6. Align the projection on the bottom of the rider seat with the “h” posi- tion slot, and then push the rear of the seat down to lock it in place as shown. 7. Install the pass...
Page 50
Instrument and control functions 3-35 3 6. Align the projection on the bottom of the rider seat with the “l” posi- tion slot, and then push the rear of the seat down to lock it in place as shown. 7. Install the passenger seat. Tip make sure that the seats are properly secured before riding. Eau39473...
Page 51
Instrument and control functions 3-36 3 warning ewa14420 ● do not exceed the load limit of 1 kg (2 lb) for storage compart- ment a. ● do not exceed the load limit of 3 kg (7 lb) for storage compart- ment b. ● do not exceed the maximum load of 215 kg (474 lb) for the ve- hicle. Eau39480 accessory box...
Page 52
Instrument and control functions 3-37 3 eau39611 adjusting the headlight beams the headlight beam adjusting knobs are used to raise or lower the height of the headlight beams. It may be neces- sary to adjust the headlight beams to increase visibility and help prevent blinding oncoming drivers when c...
Page 53
Instrument and control functions 3-38 3 3. Insert the projections into the up- per slots, and then slide the panel backward. 4. Install the quick fastener. To close a cowling vent 1. Remove the quick fastener. 2. Slide the cowling vent panel for- ward to unhook its projections from the upper slots, ...
Page 54
Instrument and control functions 3-39 3 eau39671 rear view mirrors the rear view mirrors of this vehicle can be folded forward or backward for park- ing in narrow spaces. Fold the mirrors back to their original position before riding. Warning ewa14371 be sure to fold the rear view mirrors back to th...
Page 55
Instrument and control functions 3-40 3 rebound damping force the rebound damping force is adjusted on the right front fork leg only. To increase the rebound damping force and thereby harden the rebound damp- ing, turn the adjusting knob in direction (a). To decrease the rebound damping force and th...
Page 56
Instrument and control functions 3-41 3 ber of clicks of each damping force ad- justing mechanism and to modify the specifications as necessary. Eau14916 adjusting the shock absorber assembly this shock absorber assembly is equipped with a spring preload adjust- ing lever and a rebound damping force...
Page 57
Instrument and control functions 3-42 3 tip to obtain a precise adjustment, it is ad- visable to check the actual total number of clicks or turns of the damping force adjusting mechanism. This adjustment range may not exactly match the spec- ifications listed due to small differences in production. ...
Page 58
Instrument and control functions 3-43 3 this system regularly and have a yamaha dealer repair it if it does not function properly. Eau54490 ignition circuit cut-off system the ignition circuit cut-off system (com- prising the sidestand switch, clutch switch and neutral switch) has the fol- lowing fu...
Page 59
Instrument and control functions 3-44 3 with the engine turned off: 1. Move the sidestand down. 2. Make sure that the start/engine stop switch is set to “ ”. 3. Turn the key on. 4. Shift the transmission into the neutral position. 5. Push the “ ” side of the start/engine stop switch. Does the engine...
Page 60
Instrument and control functions 3-45 3 eau39655 auxiliary dc jack warning ewa14360 to prevent electrical shock or short- circuiting, make sure that the cap is installed when the auxiliary dc jack is not being used. Notice eca15431 the accessory connected to the auxiliary dc jack should not be used ...
Page 61
For your safety – pre-operation checks 4-1 4 eau15596 inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection and maintenance procedures and schedules described in the owner’s manual. Warning ewa11151 failure to inspect or maint...
Page 62
For your safety – pre-operation checks 4-2 4 rear brake • check operation. • if soft or spongy, have yamaha dealer bleed hydraulic system. • check brake pads for wear. • replace if necessary. • check fluid level in reservoir. • if necessary, add specified brake fluid to specified level. • check hydr...
Page 63
For your safety – pre-operation checks 4-3 4 instruments, lights, signals and switches • check operation. • correct if necessary. — sidestand switch • check operation of ignition circuit cut-off system. • if system is not working correctly, have yamaha dealer check vehicle. 3-42 item checks page u1m...
Page 64
Operation and important riding points 5-1 5 eau15951 read the owner’s manual carefully to become familiar with all controls. If there is a control or function you do not understand, ask your yamaha dealer. Warning ewa10271 failure to familiarize yourself with the controls can lead to loss of con- tr...
Page 65
Operation and important riding points 5-2 5 notice eca11833 if a warning or indicator light does not come on initially when the key is turned to “on”, or if a warning or in- dicator light remains on, see page 3-4 for the corresponding warning and indicator light circuit check. The abs warning light ...
Page 66
Operation and important riding points 5-3 5 notice eca10260 ● even with the transmission in the neutral position, do not coast for long periods of time with the engine off, and do not tow the motorcycle for long dis- tances. The transmission is properly lubricated only when the engine is running. In...
Page 67
Operation and important riding points 5-4 5 1000–1600 km (600–1000 mi) avoid prolonged operation above 5400 r/min. 1600 km (1000 mi) and beyond the vehicle can now be operated nor- mally. Notice eca10310 ● keep the engine speed out of the tachometer red zone. ● if any engine trouble should oc- cur d...
Page 68
Periodic maintenance and adjustment 6-1 6 eau17244 periodic inspection, adjustment, and lu- brication will keep your vehicle in the safest and most efficient condition pos- sible. Safety is an obligation of the vehi- cle owner/operator. The most important points of vehicle inspection, adjust- ment, ...
Page 69
Periodic maintenance and adjustment 6-2 6 eau17361 owner’s tool kit the owner’s tool kit is located under the rider seat. (see page 3-32.) the service information included in this manual and the tools provided in the owner’s tool kit are intended to assist you in the performance of preventive mainte...
Page 70
Periodic maintenance and adjustment 6-3 6 eau46861 tip ● the annual checks must be performed every year, except if a kilometer-based maintenance, or for the uk, a mileage-based maintenance, is performed instead. ● from 50000 km (30000 mi), repeat the maintenance intervals starting from 10000 km (600...
Page 71
Periodic maintenance and adjustment 6-4 6 eau1770f general maintenance and lubrication chart no. Item check or maintenance job odometer reading annual check 1000 km (600 mi) 10000 km (6000 mi) 20000 km (12000 mi) 30000 km (18000 mi) 40000 km (24000 mi) 1 air filter element • clean. √ √ • replace. √ ...
Page 72
Periodic maintenance and adjustment 6-5 6 10 * swingarm • check operation and for exces- sive play. √ √ √ √ • lubricate with lithium-soap-based grease. Every 50000 km (30000 mi) 11 * steering bearings • check bearing play and steering for roughness. √ √ √ √ √ • lubricate with lithium-soap-based grea...
Page 73
Periodic maintenance and adjustment 6-6 6 21 * rear suspension re- lay arm and con- necting arm pivoting points • check operation. √ √ √ √ • lubricate with lithium-soap-based grease. √ √ 22 engine oil • change. • check oil level and vehicle for oil leakage. √ √ √ √ √ √ 23 engine oil filter car- trid...
Page 74
Periodic maintenance and adjustment 6-7 6 eau17670 tip ● the air filter needs more frequent service if you are riding in unusually wet or dusty areas. ● hydraulic brake and clutch service • regularly check and, if necessary, correct the brake and clutch fluid levels. • every two years replace the in...
Page 75
Periodic maintenance and adjustment 6-8 6 eau18771 removing and installing pan- els the panels shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a panel needs to be removed and installed. Eau54130 panel a to remove the panel 1...
Page 76
Periodic maintenance and adjustment 6-9 6 3. Take the front cowling off as shown. 4. Remove the bolt, screw and quick fastener, and then take the panel off. To install the panel 1. Place the panel in its original posi- tion, and then install the bolt, screw and quick fastener. 2. Place the front cow...
Page 77
Periodic maintenance and adjustment 6-10 6 3. Pull the bottom of the panel out- ward, pull the front of the panel downward, and then slide the pan- el forward to release it in the rear as shown. To install a panel 1. Place the panel in the original posi- tion, and then install the bolts and the quic...
Page 78
Periodic maintenance and adjustment 6-11 6 eau19652 checking the spark plugs the spark plugs are important engine components, which should be checked periodically, preferably by a yamaha dealer. Since heat and deposits will cause any spark plug to slowly erode, they should be removed and checked in ...
Page 79
Periodic maintenance and adjustment 6-12 6 eau19886 engine oil and oil filter car- tridge the engine oil level should be checked before each ride. In addition, the oil must be changed and the oil filter car- tridge replaced at the intervals speci- fied in the periodic maintenance and lubrication cha...
Page 80
Periodic maintenance and adjustment 6-13 6 tip an oil filter wrench is available at a yamaha dealer. 6. Apply a thin coat of clean engine oil to the o-ring of the new oil filter cartridge. Tip make sure that the o-ring is properly seated. 7. Install the new oil filter cartridge, and then tighten it ...
Page 81
Periodic maintenance and adjustment 6-14 6 notice eca11620 ● in order to prevent clutch slip- page (since the engine oil also lubricates the clutch), do not mix any chemical additives. Do not use oils with a diesel speci- fication of “cd” or oils of a high- er quality than specified. In addition, do...
Page 82
Periodic maintenance and adjustment 6-15 6 tip the oil level should be at the brim of the filler hole. 3. If the oil is below the brim of the fill- er hole, add sufficient oil of the rec- ommended type to raise it to the correct level. 4. Check the gasket for damage, and replace it if necessary. 5. ...
Page 83
Periodic maintenance and adjustment 6-16 6 eau20070 coolant the coolant level should be checked before each ride. In addition, the cool- ant must be changed at the intervals specified in the periodic maintenance and lubrication chart. Eau54160 to check the coolant level 1. Place the vehicle on the c...
Page 84
Periodic maintenance and adjustment 6-17 6 eau33031 changing the coolant the coolant must be changed at the in- tervals specified in the periodic mainte- nance and lubrication chart. Have a yamaha dealer change the coolant. Warning! Never attempt to remove the radiator cap when the engine is hot. [e...
Page 85
Periodic maintenance and adjustment 6-18 6 out with compressed air as shown. If the air filter element is damaged, replace it. 6. Insert the air filter element into the air filter case. Notice: make sure that the air filter element is prop- erly seated in the air filter case. The engine should never...
Page 86
Periodic maintenance and adjustment 6-19 6 eau21384 checking the throttle grip free play the throttle grip free play should mea- sure 3.0–5.0 mm (0.12–0.20 in) at the inner edge of the throttle grip. Periodi- cally check the throttle grip free play and, if necessary, have a yamaha deal- er adjust it...
Page 87
Periodic maintenance and adjustment 6-20 6 weight of rider, passenger, car- go, and accessories approved for this model. Warning ewa10511 never overload your vehicle. Opera- tion of an overloaded vehicle could cause an accident. Tire inspection the tires must be checked before each ride. If the cent...
Page 88
Periodic maintenance and adjustment 6-21 6 tire information this motorcycle is equipped with tube- less tires, tire air valves and cast wheels. Tires age, even if they have not been used or have only been used occasion- ally. Cracking of the tread and sidewall rubber, sometimes accompanied by carcas...
Page 89
Periodic maintenance and adjustment 6-22 6 “broken in”. Therefore, it is ad- visable before doing any high- speed riding to ride conserva- tively for approximately 100 km (60 mi) after installing a new tire. ● the tires must be warmed up before a high-speed run. ● always adjust the tire air pres- su...
Page 90
Periodic maintenance and adjustment 6-23 6 eau37913 checking the brake lever free play there should be no free play at the brake lever end. If there is free play, have a yamaha dealer inspect the brake system. Warning ewa14211 a soft or spongy feeling in the brake lever can indicate the presence of ...
Page 91
Periodic maintenance and adjustment 6-24 6 eau22392 checking the front and rear brake pads the front and rear brake pads must be checked for wear at the intervals spec- ified in the periodic maintenance and lubrication chart. Eau43431 front brake pads the front brake calipers are equipped with two s...
Page 92
Periodic maintenance and adjustment 6-25 6 rear brake clutch tip the rear brake fluid reservoir is located behind panel c. (see page 6-8.) warning ewa16030 improper maintenance can result in loss of braking ability or clutch oper- ation. Observe these precautions: ● insufficient brake or clutch flui...
Page 93
Periodic maintenance and adjustment 6-26 6 eau22752 changing the brake and clutch fluids have a yamaha dealer change the brake and clutch fluids at the intervals specified in the periodic maintenance and lubrication chart or in the tip after the periodic maintenance and lubrica- tion chart. In addit...
Page 94
Periodic maintenance and adjustment 6-27 6 eau44273 checking and lubricating the brake and shift pedals the operation of the brake and shift pedals should be checked before each ride, and the pedal pivots should be lu- bricated if necessary. Brake pedal shift pedal eau43601 checking and lubricating ...
Page 95
Periodic maintenance and adjustment 6-28 6 eau23213 checking and lubricating the centerstand and sidestand the operation of the centerstand and sidestand should be checked before each ride, and the pivots and metal-to- metal contact surfaces should be lubri- cated if necessary. Warning ewa10741 if t...
Page 96
Periodic maintenance and adjustment 6-29 6 eau23251 lubricating the rear suspen- sion the pivoting points of the rear suspen- sion must be lubricated by a yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart. Eaum1652 lubricating the swingarm piv- ots the swinga...
Page 97
Periodic maintenance and adjustment 6-30 6 notice eca10590 if any damage is found or the front fork does not operate smoothly, have a yamaha dealer check or re- pair it. Eau45511 checking the steering worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be ...
Page 98
Periodic maintenance and adjustment 6-31 6 eau39525 battery the battery is located under panel a. (see page 6-8.) this model is equipped with a vrla (valve regulated lead acid) battery. There is no need to check the electro- lyte or to add distilled water. However, the battery lead connections need ...
Page 99
Periodic maintenance and adjustment 6-32 6 is turned to “off”, then con- nect the positive lead before connecting the negative lead. [eca16840] 4. After installation, make sure that the battery leads are properly con- nected to the battery terminals. Notice eca16530 always keep the battery charged. ...
Page 100
Periodic maintenance and adjustment 6-33 6 2. Remove the blown fuse, and then install a new fuse of the specified amperage. Warning! Do not use a fuse of a higher amperage rating than recommended to avoid causing extensive dam- age to the electrical system and possibly a fire. [ewa15131] 3. Turn the...
Page 101
Periodic maintenance and adjustment 6-34 6 eau40361 headlight bulb if a headlight does not come on, have a yamaha dealer check its electrical cir- cuit or replace the bulb. Notice eca16580 do not affix any type of tinted film or stickers to the headlight lens. Eau54240 front turn signal light this m...
Page 102
Periodic maintenance and adjustment 6-35 6 5. Install the socket (together with the bulb) by turning it clockwise. 6. Install the passenger seat. Eau24313 replacing the license plate light bulb 1. Remove the license plate light unit by removing the screws. 2. Remove the license plate light bulb sock...
Page 103
Periodic maintenance and adjustment 6-36 6 eau54500 auxiliary light this model is equipped with led-type auxiliary lights. If an auxiliary light does not come on, have a yamaha dealer check it. Eau25871 troubleshooting although yamaha motorcycles receive a thorough inspection before shipment from th...
Page 104
Periodic maintenance and adjustment 6-37 6 eau42504 troubleshooting charts starting problems or poor engine performance check the fuel level in the fuel tank. 1. Fuel there is enough fuel. There is no fuel. Check the battery. Supply fuel. The engine does not start. Check the battery. Remove the spar...
Page 105
Periodic maintenance and adjustment 6-38 6 engine overheating warning ewat1040 ● do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled. ● place a...
Page 106: Motorcycle Care and Storage
Motorcycle care and storage 7-1 7 eau37833 matte color caution notice eca15192 some models are equipped with matte colored finished parts. Be sure to consult a yamaha dealer for advice on what products to use be- fore cleaning the vehicle. Using a brush, harsh chemical products or cleaning compounds...
Page 107: Motorcycle Care and Storage
Motorcycle care and storage 7-2 7 off any detergent residue using plenty of water, as it is harmful to plastic parts. ● do not use any harsh chemical products on plastic parts. Be sure to avoid using cloths or sponges which have been in contact with strong or abrasive cleaning products, solvent or t...
Page 108: Motorcycle Care and Storage
Motorcycle care and storage 7-3 7 windshield. Before using them, make a test by polishing an area which does not affect your visibility. After cleaning 1. Dry the motorcycle with a chamois or an absorbing cloth. 2. Use a chrome polish to shine chrome, aluminum and stainless- steel parts, including t...
Page 109: Motorcycle Care and Storage
Motorcycle care and storage 7-4 7 eau26243 storage short-term always store your motorcycle in a cool, dry place and, if necessary, protect it against dust with a porous cover. Be sure the engine and the exhaust sys- tem are cool before covering the motor- cycle. Notice eca10810 ● storing the motorcy...
Page 110: Motorcycle Care and Storage
Motorcycle care and storage 7-5 7 tip make any necessary repairs before storing the motorcycle. U1mce0e0.Book page 5 thursday, july 19, 2012 6:59 pm.
Page 111: Specifications
Specifications 8-1 8 dimensions: overall length: 2230 mm (87.8 in) overall width: 750 mm (29.5 in) overall height: 1325/1455 mm (52.2/57.3 in) seat height: 805/825 mm (31.7/32.5 in) wheelbase: 1545 mm (60.8 in) ground clearance: 130 mm (5.12 in) minimum turning radius: 3100 mm (122.0 in) weight: cur...
Page 112: Specifications
Specifications 8-2 8 secondary reduction ratio: 2.698 (35/37 x 21/27 x 33/9) transmission type: constant mesh 5-speed operation: left foot operation gear ratio: 1st: 2.529 (43/17) 2nd: 1.773 (39/22) 3rd: 1.348 (31/23) 4th: 1.077 (28/26) 5th: 0.929 (26/28) chassis: frame type: diamond caster angle: 2...
Page 113: Specifications
Specifications 8-3 8 rear suspension: type: swingarm (link suspension) spring/shock absorber type: coil spring/gas-oil damper wheel travel: 125.0 mm (4.92 in) electrical system: ignition system: tci charging system: ac magneto battery: model: gt14b-4 voltage, capacity: 12 v, 12.0 ah headlight: bulb ...
Page 114: Consumer Information
Consumer information 9-1 9 eau48612 identification numbers record the vehicle identification num- ber and model label information in the spaces provided below for assistance when ordering spare parts from a yamaha dealer or for reference in case the vehicle is stolen. Vehicle identification number: ...
Page 115: Index
Index a abs ...................................................... 3-26 abs warning light ................................... 3-5 accessory box ...................................... 3-36 air filter element, cleaning .................... 6-17 auxiliary dc jack .................................. 3-45...
Page 116: Index
Index storage compartments.......................... 3-35 swingarm pivots, lubricating ................. 6-29 t throttle grip and cable, checking and lubricating ........................................... 6-26 throttle grip free play, checking............ 6-19 tires ...................................
Page 117
U1mce0e0.Book page 3 thursday, july 19, 2012 6:59 pm.
Page 118
Printed in japan 2012.07-0.3 × 1 cr (e) dic183 printed on recycled paper.