- DL manuals
- Yamaha
- Conference System
- PJP-50R
- Basic Operation Manual
Yamaha PJP-50R Basic Operation Manual
Summary of PJP-50R
Page 1
Pjp-50r 1 2 3 4 5 6 7 8 9 0 mic mute hook / standby vol owner’s manual mode d’emploi bedienungsanleitung g ip audio conference system système de conférence audio ip basic operation guide guide de fonctionnement de base grundlegende bedienungsanleitung.
Page 2
Important safety instructions i english • explanation of graphical symbols the lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to cons...
Page 3
Important safety instructions ii d) if the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a ...
Page 4: III
Important safety instructions iii english fcc information (for us customers) for canadian customers this product meets the applicable industry canada technical specifications. The ringer equivalence number (ren) is an indication of the maximum number of devices allowed to be connected to a telephone...
Page 5
Iv 1 to assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 install this unit in a well ventilated, cool, dry, clean place with at least 10 cm on the top, 10 cm on the left and right, and 10 cm at the back of this unit — away from direct ...
Page 6: Contents
1 b a sic call opera t ions intr oduction ad ditional info rma t ion english features .................................................................. 2 about this manual ................................................. 3 supplied accessories ................................................ 3 con...
Page 7: Features
2 this system is an audio conference system that connects ip networks including the internet and corporate lan as well as analog telephone circuits to hold simultaneous communications between multiple persons in multiple locations. Voice conference through network/analog telephone circuits this syst...
Page 8: About This Manual
English 3 features intr oduction • in this manual, the names of the following products are denoted as follows. – yamaha pjp-50r: this unit – microsoft ® windows ® : windows – microsoft ® windows xp ® : windows xp – 10base-t (100base-tx) cable: lan cable • the ip addresses, domain names, and url name...
Page 9: Controls and Functions
Controls and functions 4 ■ top panel 1 microphone indicators a blue led lights to indicate the audio pick up area. 2 arrayed microphones the 16 microphones on the top panel capture the voices of the talkers. 3 (connect) key press the key when placing a call to the designated destination or receiving...
Page 10
5 controls and functions intr oduction english ■ side panel 1 line port connect an analog telephone circuit. 2 lan port connect a lan cable for connection to network equipment such as a pc, router, or hub. The led lights up when the port is connected to a network and blinks according to the communic...
Page 11
6 controls and functions ■ display 1 communication mode indicator indicates the communication mode used in the communication through the ip network. • : call by designating the ip address. • : call using a sip server. Y communication through the telephone circuit is possible regardless of the commun...
Page 12: Calling Another Party
Communication through ip network 7 b a sic call opera t ions english to place a call to another party, enter its ip address. Before using the functions of this system, it is necessary to install, connect, and set up the system. For details, refer to the “setup guide” (a separate manual). 1 press rep...
Page 13: Address Book
Communication through ip network 8 the following display appears if the call is connected and conversation becomes available. Y press during communication to view the setting of the system as shown below. • do not disconnect the lan cable or power cable during a call. Doing so may cause malfunction....
Page 14: History
Communication through ip network 9 b a sic call opera t ions english follow the procedure below to call another party by referring to the history of past outgoing or incoming calls. If the destination obtains the ip address from a dhcp server, its ip address may have changed from the last call. If y...
Page 15: Adjusting The Speaker Volume
Operations during communication through ip network 10 press vol + or – during communication to adjust the speaker output volume. ■ muting the microphone input temporarily if the persons in your location want to discuss in private, press mic mute. The microphones are switched off, and the led of mic ...
Page 16
Operations during communication through ip network 11 b a sic call opera t ions english in the “microphone mode” menu, press a numeric key to specify the area in which tracking is disabled. Every numeric key enables or disables the tracking in the direction corresponding to the key as shown in the f...
Page 17
Talking with multiple locations 12 this system enables simultaneous talk between up to four locations (with the mesh connection) through an ip network. It is also possible to call additional locations as required during a call. To hold a communication between multiple locations, begin a call with a ...
Page 18: Multiple Connections
Talking with multiple locations 13 b a sic call opera t ions english the information display and speaker output method vary depending on the settings in “connection mode” (page 14 in the “setup guide” (a separate manual)) and “speaker mode” (page 17 in the “setup guide” (a separate manual)). ■ when ...
Page 19: Calling Another Party
Communication through telephone circuit 14 to place a call to another party, enter its telephone number. • before using the functions of this system, it is necessary to install, connect, and set up the system. For details, refer to the “setup guide” (a separate manual). • before using this function,...
Page 20: Address Book
Communication through telephone circuit 15 b a sic call opera t ions english the following display appears if the call is connected and conversation becomes available. Y press during communication to view the setting of the system as shown below. • do not disconnect the modular telephone cable or po...
Page 21: History
Communication through telephone circuit 16 follow the procedure below to call another party by referring to the history of past outgoing or incoming calls. 1 press repeatedly until the initial display appears. 2 press . The menu screen appears. 3 press or to select “2. Call history”, and then press ...
Page 22: Adjusting The Speaker Volume
Operations during communication through telephone circuit 17 b a sic call opera t ions english press vol + or – during communication to adjust the speaker output volume. ■ muting the microphone input temporarily if the persons in your location want to discuss in private, press mic mute. The micropho...
Page 23
Operations during communication through telephone circuit 18 in the “microphone mode” menu, press a numeric key to specify the area in which tracking is disabled. Every numeric key enables or disables the tracking in the direction corresponding to the key as shown in the following illustration. All ...
Page 24: Sending Tone Signals
Operations during communication through telephone circuit 19 b a sic call opera t ions english tone signals can be transmitted during communication. This is convenient when using a service that requires tone input during a call, such as the answering service of a cellular phone. 1 press during commu...
Page 25: Troubleshooting
Troubleshooting 20 refer to the following tables when this unit does not function properly. If the problem you are experiencing is not listed or if the instruction does not help, contact your nearest authorized yamaha dealer or service center. First, check if the microphone indicators light up. If t...
Page 26: Q2: A Call Cannot Be Made
21 troubleshooting english a dditional inf o r m a t io n q2: a call cannot be made problem cause remedy a call cannot be originated. An inappropriate ip address is entered. Check the ip address of the other unit and enter the correct ip address. The ip address of the other unit has been changed. Ch...
Page 27: Q3: Other Problems
22 troubleshooting problem cause remedy a call cannot be received. The connection mode settings of this unit and the other unit are different. A unit in the mesh connection mode cannot communicate with a unit in a cascade connection mode. Set the two units to the same connection mode (page 14 in the...
Page 28
Yamaha corporation 10-1 nakazawa-cho, hamamatsu, shizuoka 430-8650, japan © 2006 all rights reserved. Printed in japan wj13580-2 this owner’s manual is based on the latest version of the firmware as of october, 2007. The functions and specifications could be possibly added or changed by a firmware u...