Yamaha RSio64-D Owner's Manual - page 10
10
Owner’s Manual
Controls and Functions
r
WORD CLOCK select key
Selects the word clock source of the RSio64-D.
WORD CLOCK [WCLK IN] indicator
WORD CLOCK [SLOT1 1/2] indicator
WORD CLOCK [DANTE] indicator
These indicate the status of the RSio64-D’s word clock
source.
*1 When this is flashing, the
u
nit
u
ses the Dante
w
ord clock to
operate and perform inp
u
t/o
u
tp
u
t.
*2 In order to
u
se MY
8
-AEB, set AE
RSVD s
w
itch to the
RSVD position.
*3 If yo
u
w
ant to change the freq
u
ency of the Dante
w
ord
clock,
u
se Dante Controller.
t
ROUTING [PATTERN] rotary switch
This selects the RSio64-D’s internal audio routing
pattern from seven preset patterns and one user
pattern. Setting the rotary switch to 1–7 selects preset
routing patterns 1–7, and setting it to 0 selects the user
routing pattern.
NOTE
The ro
u
ting pattern does not change if yo
u
select
8
–F.
y
SETUP [UNIT ID] rotary switch
Specifies an ID that identifies this device on the Dante
network. If there are multiple Dante-compatible
devices from Yamaha that require an ID setting
connected to the same network, set a different ID for
each device.
u
Device setting DIP switches
These switches specify startup settings for the device.
Details are given below.
The switch illustrations indicate the setting state as
follows.
• Switch 1 (UNIT ID)
This switch setting determines whether the [UNIT ID]
setting will range from hexadecimal 00 to 0F or from 10
to 1F.
• Switch 2/Switch 3 (IP SETTING)
These specify the method of setting the IP address used
when communicating with an external device such as R
Remote V3. When connecting the RSio64-D to a
computer for the first time immediately after purchase,
set this to something other than STATIC IP (MANUAL).
If you want to set this to STATIC IP (MANUAL), first
specify the IP address from R Remote V3 and then
switch this setting to STATIC IP (MANUAL).
WCLK IN
This is lit if the RSio64-D is
u
sing the
w
ord
clock that is
b
eing inp
u
t from the rear panel
[WORD CLOCK IN] connector. This flashes if
there is no
v
alid
w
ord clock inp
u
t
*1
.
SLOT1 1/2
This is lit if the channel 1/2
w
ord clock of slot 1
is
b
eing
u
sed. This flashes if there is no
v
alid
w
ord clock inp
u
t
*1
. The channel 7/
8
w
ord clock
is
u
sed
w
hen
u
sing the MY
8
-AEB
*2
.
DANTE
This is lit if the Dante net
w
ork’s
w
ord clock
*3
is
b
eing
u
sed. (If no
v
alid Dante signal is
b
eing
inp
u
t, the clock generated
b
y the internal
Dante mod
u
le is
u
sed.)
Making the setting
You can select the routing pattern even when the
power is on. Your selection is applied three seconds
after you switch the routing pattern.
Making the setting
Turn off the power before you change the setting of
this rotary switch. The setting is applied the next
time you turn the power on. If you change the
setting while the power is on, the changed setting is
not applied until the power is turned off and on
again.
Making the setting
Turn off the power before you change these DIP
switch settings. The setting is applied the next time
you turn the power on. If you change the setting
while the power is on, the changed setting is not
applied until the power is turned off and on again.
Switch
State
S
w
itch is in the
u
p
w
ard (OFF) position.
S
w
itch is in the do
w
n
w
ard (ON) position.
Switch
Setting
Description
UNIT ID =
00-0F
The UNIT ID setting range is 00
to 0F.
UNIT ID =
10-1F
The UNIT ID setting range is 10
to 1F.
Switch
Setting
Description
AUTO IP
The Dante net
w
ork a
u
tomati-
cally specifies the IP address as
169.254.XX.XX.
DHCP
The IP address assigned from
the DHCP ser
v
er is
u
sed.
STATIC IP
(AUTO)
The IP address is specified as
192.16
8
.0.xx (xx=UNIT ID).
STATIC IP
(MANUAL)
The IP address is specified from
an external de
v
ice s
u
ch as R
Remote V3.
O
N
1 2 3 4 5 6 7 8
UNIT ID
IP SETTING
SECONDARY PORT
START UP MODE
1
1
2
3
2
3
3
2
3
2