- DL manuals
- Yamaha
- Motorcycle
- WR450F
- Owner's Manual
Yamaha WR450F Owner's Manual
Summary of WR450F
Page 1
Q read this manual carefully before operating this vehicle. Owner’s manual wr450f 1dx-28199-e1 u1dxe1_hyoshi.Indd 1 2012/08/08 17:42:00
Page 2
Q read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold. Eau46090 u1dxe1_hyoshi.Indd 2 2012/08/08 17:42:01.
Page 3: Introduction
Introduction eau10102 welcome to the yamaha world of motorcycling! As the owner of the wr450f, you are benefiting from yamaha’s vast experience and newest technology regarding the de- sign and manufacture of high-quality products, which have earned yamaha a reputation for dependability. Please take ...
Page 4: Important Manual Information
Important manual information eau10133 particularly important information is distinguished in this manual by the following notations: *product and specifications are subject to change without notice. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey a...
Page 5: Important Manual Information
Important manual information eau10200 wr450f owner’s manual ©2012 by yamaha motor co., ltd. 1st edition, july 2012 all rights reserved. Any reprinting or unauthorized use without the written permission of yamaha motor co., ltd. Is expressly prohibited. Printed in japan. 1dx-9-e1.Book 2 ページ ２０１２年７月３１...
Page 6: Table of Contents
Table of contents safety information .................. 1-1 description .................................. 2-1 left view .......................................... 2-1 right view ........................................ 2-2 controls and instruments................. 2-3 instrument and control functio...
Page 7: Table of Contents
Table of contents checking the steering ................... 6-30 checking the wheel bearings ....... 6-30 battery .......................................... 6-30 replacing the fuse ........................ 6-32 replacing the headlight bulb ........ 6-32 tail/brake light ................................
Page 8: Safety Information
1-1 1 safety information eau53004 be a responsible owner as the vehicle’s owner, you are respon- sible for the safe and proper operation of your motorcycle. Motorcycles are single-track vehicles. Their safe use and operation are de- pendent upon the use of proper riding techniques as well as the exp...
Page 9: Safety Information
1-2 1 safety information motorist’s blind spot. • never maintain a motorcycle without proper knowledge. Con- tact an authorized motorcycle dealer to inform you on basic motorcycle maintenance. Cer- tain maintenance can only be carried out by certified staff. many accidents involve inexperi- enced ...
Page 10: Safety Information
1-3 safety information 1 unable to save yourself. Also, deadly levels of carbon monoxide can linger for hours or days in enclosed or poorly ventilated areas. If you experience any symptoms of carbon monoxide poison- ing, leave the area immediately, get fresh air, and seek medical treat- ment. do n...
Page 11: Safety Information
1-4 1 safety information mended by yamaha, even if sold and installed by a yamaha dealer. Aftermarket parts, accessories, and modifications while you may find aftermarket prod- ucts similar in design and quality to genuine yamaha accessories, recog- nize that some aftermarket accessories or modifica...
Page 12: Safety Information
1-5 safety information 1 tie-downs or suitable straps that are attached to solid parts of the motorcycle, such as the frame or upper front fork triple clamp (and not, for example, to rubber-mount- ed handlebars or turn signals, or parts that could break). Choose the location for the straps carefully...
Page 13: Description
2-1 1 2 description eau10410 left view 12 1, 2 3 4, 5 6 7 8 10 9 11 1. Front fork compression damping force adjusting screw (page 3-14) 2. Bleed screw (page 3-15) 3. Starter knob (page 3-12) 4. Battery (page 6-30) 5. Main fuse (page 6-32) 6. Air filter element (page 6-14) 7. Engine oil check bolt (p...
Page 14: Description
Description 2-2 1 2 3 4 5 6 7 8 9 eau10420 right view 1, 2 3 5 7 8 11 6 10 12 9 4 1. Shock absorber assembly compression damping force adjusting screw (for slow compression damping) (page 3-16) 2. Shock absorber assembly compression damping force adjusting nut (for fast compression damping) (page 3-...
Page 15: Description
Description 2-3 2 3 4 5 6 7 8 9 eau10430 controls and instruments 1 2 3 4 5 6 8 7 1. Clutch lever (page 3-8) 2. Left handlebar switches (page 3-7) 3. Multi-function display (page 3-2) 4. Main switch (page 3-1) 5. Front brake fluid reservoir (page 6-23) 6. Right handlebar switches (page 3-7) 7. Brake...
Page 16
3-1 1 2 3 4 5 6 7 8 9 instrument and control functions eau10451 main switch the main switch controls the ignition and lighting systems. The various main switch positions are described below. Eau52430 on all electrical circuits are supplied with power; the meter lighting, taillight, li- cense plate l...
Page 17
Instrument and control functions 3-2 2 3 4 5 6 7 8 9 eau11080 high beam indicator light “ ” this indicator light comes on when the high beam of the headlight is switched on. Eau52390 fuel level warning light “ ” this warning light comes on when the fuel level drops below approximately 3.0 l (0.79 us...
Page 18
Instrument and control functions 3-3 1 2 3 4 5 6 7 8 9 tip the multi-function display can be set to the basic mode or the mea- surement mode. tripmeter a will automatically re- set to zero when changing from the basic mode to the measure- ment mode or vice versa. Basic mode: a speedometer an...
Page 19
Instrument and control functions 3-4 2 3 4 5 6 7 8 9 tip indicator “ ” comes on when tripmeter a is selected, and indicator “ ” comes on when tripmeter b is selected. To reset a tripmeter, select it by push- ing the “slct 2” button, and then push the “rst” button for at least one sec- ond. Clock the...
Page 20
Instrument and control functions 3-5 1 2 3 4 5 6 7 8 9 tip starting measurement consists of the following two starts, either of which can be selected. manual start starting measurement by the rider himself operating the button. (a long push on the “slct 2” button will put measurement on standby.) ...
Page 21
Instrument and control functions 3-6 2 3 4 5 6 7 8 9 ton together again. Tip the stopwatch will continue counting when the vehicle is stopped. To stop and/or resume counting, repeat steps 3 and 4. Measurement mode (for calibrating the distance-compensation tripme- ter’s reading) the distance-compens...
Page 22
Instrument and control functions 3-7 1 2 3 4 5 6 7 8 9 eau1234b handlebar switches left right eau12400 dimmer switch “ / ” set this switch to “ ” for the high beam and to “ ” for the low beam. Eau12460 turn signal switch “ / ” to signal a right-hand turn, push this switch to “ ”. To signal a left-ha...
Page 23
Instrument and control functions 3-8 2 3 4 5 6 7 8 9 eau12820 clutch lever the clutch lever is located at the left handlebar grip. To disengage the clutch, pull the lever toward the handle- bar grip. To engage the clutch, release the lever. The lever should be pulled rapidly and released slowly for ...
Page 24
Instrument and control functions 3-9 1 2 3 4 5 6 7 8 9 3. While holding the lever pushed away from the throttle grip, turn the adjusting bolt in direction (a) to in- crease the distance, and in direc- tion (b) to decrease it. 4. Tighten the locknut. 5. Slide the rubber cover to its origi- nal positi...
Page 25
Instrument and control functions 3-10 2 3 4 5 6 7 8 9 eau13212 fuel make sure there is sufficient gasoline in the tank. Warning ewa10881 gasoline and gasoline vapors are extremely flammable. To avoid fires and explosions and to reduce the risk of injury when refueling, follow these instructions. 1. ...
Page 26
Instrument and control functions 3-11 1 2 3 4 5 6 7 8 9 spark plug life and reduce maintenance costs. Eau41360 fuel tank breather hose before operating the motorcycle: check the fuel tank breather hose connection. check the fuel tank breather hose for cracks or damage, and replace it if damaged....
Page 27
Instrument and control functions 3-12 2 3 4 5 6 7 8 9 converter. Eau53230 starter knob starting a cold engine requires a richer air-fuel mixture, which is supplied by the starter. Move the knob in direction (a) to turn on the starter. Move the knob in direction (b) to turn off the starter. Eau13650 ...
Page 28
Instrument and control functions 3-13 1 2 3 4 5 6 7 8 9 eau53100 steering lock to lock the steering 1. Turn the handlebar all the way to the left. 2. Insert the key into the steering lock under the steering head pipe, and then turn it 1/2 turn in either direc- tion. 3. Check that the steering is loc...
Page 29
Instrument and control functions 3-14 2 3 4 5 6 7 8 9 to install the seat 1. Fit the slot in the seat onto the pro- jection on the fuel tank. 2. Place the seat in the original posi- tion, and then tighten the bolts. Tip make sure that the seat is properly se- cured before riding. Eau52450 adjusting ...
Page 30
Instrument and control functions 3-15 1 2 3 4 5 6 7 8 9 each fork leg in direction (b). Tip although the total number of clicks of a damping force adjusting mechanism may not exactly match the above spec- ifications due to small differences in production, the actual number of clicks always represent...
Page 31
Instrument and control functions 3-16 2 3 4 5 6 7 8 9 3. Install the bleed screws. 4. Lower the front wheel so that it is on the ground, and then put the sidestand down. Eau52892 adjusting the shock absorber assembly this shock absorber assembly is equipped with a spring preload adjust- ing ring, a ...
Page 32
Instrument and control functions 3-17 1 2 3 4 5 6 7 8 9 compression damping force compression damping force (for fast compression damping) to increase the compression damping force and thereby harden the compres- sion damping, turn the adjusting bolt in direction (a). To decrease the compres- sion d...
Page 33
Instrument and control functions 3-18 2 3 4 5 6 7 8 9 visable to check the actual total number of clicks or turns of each damping force adjusting mechanism. This adjustment range may not exactly match the spec- ifications listed due to small differences in production. Warning ewa10221 this shock abs...
Page 34
Instrument and control functions 3-19 1 2 3 4 5 6 7 8 9 yamaha dealer repair it if it does not function properly. Eau52861 ignition circuit cut-off system the ignition circuit cut-off system (com- prising the sidestand switch, clutch switch and neutral switch) has the fol- lowing functions. it pre...
Page 35
Instrument and control functions 3-20 2 3 4 5 6 7 8 9 with the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is set to “ 3. Push the main switch to “on”. 4. Shift the transmission into the neutral position. 5. Push the start switch. Does the engine start? Wi...
Page 36
4-1 1 2 3 4 5 6 7 8 9 for your safety – pre-operation checks eau15596 inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection and maintenance procedures and schedules described in the owner’s manual. Warning ewa11151 failure to ...
Page 37
For your safety – pre-operation checks 4-2 2 3 4 5 6 7 8 9 rear brake • check operation. • if soft or spongy, have yamaha dealer bleed hydraulic system. • check brake pads for wear. • replace if necessary. • check fluid level in reservoir. • if necessary, add specified brake fluid to specified level...
Page 38
For your safety – pre-operation checks 4-3 1 2 3 4 5 6 7 8 9 chassis fasteners • make sure that all nuts, bolts and screws are properly tightened. • tighten if necessary. — instruments, lights, signals and switches • check operation. • correct if necessary. — sidestand switch • check operation of ig...
Page 39
5-1 2 3 4 5 6 7 8 9 operation and important riding points eau15951 read the owner’s manual carefully to become familiar with all controls. If there is a control or function you do not understand, ask your yamaha dealer. Warning ewa10271 failure to familiarize yourself with the controls can lead to l...
Page 40
Operation and important riding points 5-2 1 2 3 4 5 6 7 8 9 pushed to “on”, or if a warning light remains on, see page 3-1 for the cor- responding warning light circuit check. 2. Shift the transmission into the neu- tral position. The neutral indicator light should come on. If not, ask a yamaha deal...
Page 41
Operation and important riding points 5-3 2 3 4 5 6 7 8 9 tip if the engine fails to start, push the main switch to “off” and give the kickstarter 10 to 20 slow kicks at full throttle in or- der to clear the engine of the rich air-fu- el mixture retained in it. Eau52971 starting a warm engine follow...
Page 42
Operation and important riding points 5-4 1 2 3 4 5 6 7 8 9 the neutral position, do not coast for long periods of time with the engine off, and do not tow the motorcycle for long dis- tances. The transmission is properly lubricated only when the engine is running. Inade- quate lubrication may damag...
Page 43
Operation and important riding points 5-5 2 3 4 5 6 7 8 9 5. Start the engine and check the op- eration of the motorcycle through- out its entire operating range. Restart the motorcycle and ride it for about 10 to 15 more minutes. The motorcycle will now be ready to ride normally. After the engine b...
Page 44
6-1 1 2 3 4 5 6 7 8 9 periodic maintenance and adjustment eau17244 periodic inspection, adjustment, and lu- brication will keep your vehicle in the safest and most efficient condition pos- sible. Safety is an obligation of the vehi- cle owner/operator. The most important points of vehicle inspection...
Page 45
Periodic maintenance and adjustment 6-2 2 3 4 5 6 7 8 9 eau17311 owner’s tool kit the service information included in this manual and the tools provided in the owner’s tool kit are intended to assist you in the performance of preventive maintenance and minor repairs. How- ever, additional tools such...
Page 46
Periodic maintenance and adjustment 6-3 1 2 3 4 5 6 7 8 9 eau52500 tip the annual checks must be performed every year, except if a kilometer-based maintenance, or for the uk, a mileage-based maintenance, is performed instead. from 7000 km (4200 mi) or 9 months, repeat the maintenance intervals s...
Page 47
Periodic maintenance and adjustment 6-4 2 3 4 5 6 7 8 9 eau52581 general maintenance and lubrication chart no. Item checks and maintenance jobs initial odometer readings annual check 1000 km (600 mi) or 1 month 3000 km (1800 mi) or 3 months 5000 km (3000 mi) or 6 months 1 * air filter element • clea...
Page 48
Periodic maintenance and adjustment 6-5 1 2 3 4 5 6 7 8 9 12 * steering bearings • check bearing play and steering for roughness. • lubricate with lithium-soap-based grease. 13 * chassis fasteners • make sure that all nuts, bolts and screws are properly tightened. 14 brake lever pivot shaft • lubric...
Page 49
Periodic maintenance and adjustment 6-6 2 3 4 5 6 7 8 9 eau53210 tip the air filter needs more frequent service if you are riding in unusually wet or dusty areas. hydraulic brake service • regularly check and, if necessary, correct the brake fluid level. • every two years replace the internal co...
Page 50
Periodic maintenance and adjustment 6-7 1 2 3 4 5 6 7 8 9 eau18751 removing and installing the panel the panel shown needs to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time the panel needs to be removed and installed. Eau52872 panel a to...
Page 51
Periodic maintenance and adjustment 6-8 2 3 4 5 6 7 8 9 wire thickness gauge and, if necessary, adjusted to specification. Clean the surface of the spark plug gasket and its mating surface, and then wipe off any grime from the spark plug threads. Tip if a torque wrench is not available when installi...
Page 52
Periodic maintenance and adjustment 6-9 1 2 3 4 5 6 7 8 9 and do not touch the radiator pipe after high-speed operation, otherwise the cooling system is hot and cause burns. Always let the engine oil cool down suffi- ciently before removing the oil tank cap. [ewa16140] notice: do not operate the veh...
Page 53
Periodic maintenance and adjustment 6-10 2 3 4 5 6 7 8 9 6. Install the engine oil tank cap, and then the check bolt and its gasket. To change the engine oil (with or without oil filter element replace- ment) 1. Place the vehicle on a level sur- face. 2. Start the engine, warm it up for several minu...
Page 54
Periodic maintenance and adjustment 6-11 1 2 3 4 5 6 7 8 9 tip skip steps 8–10 if the oil filter element is not being replaced. 8. Remove the oil filter element cover by removing the bolts. 9. Remove and replace the oil filter element and o-rings. 10. Install the oil filter element cover by installi...
Page 55
Periodic maintenance and adjustment 6-12 2 3 4 5 6 7 8 9 mix any chemical additives. Do not use oils with a diesel speci- fication of “cd” or oils of a high- er quality than specified. In addition, do not use oils labeled “energy conserving ii” or higher. make sure that no foreign mate- rial enter...
Page 56
Periodic maintenance and adjustment 6-13 1 2 3 4 5 6 7 8 9 tip the coolant should be at the bottom of the radiator filler neck. The level will change with variation of engine temper- ature. 3. If the coolant is below the correct coolant level, add coolant, and then install the radiator cap. Notice: ...
Page 57
Periodic maintenance and adjustment 6-14 2 3 4 5 6 7 8 9 into the radiator until it is full. 7. Install the radiator cap, start the engine, let it idle for several min- utes, and then turn it off. 8. Remove the radiator cap to check the coolant level in the radiator. If necessary, add sufficient coo...
Page 58
Periodic maintenance and adjustment 6-15 1 2 3 4 5 6 7 8 9 with solvent, and then squeeze the remaining solvent out. Warning! Use only a dedicated parts cleaning solvent. To avoid the risk of fire or explosion, do not use gasoline or solvents with a low flash point. [ewa10431] notice: to avoid damag...
Page 59
Periodic maintenance and adjustment 6-16 2 3 4 5 6 7 8 9 7. Place the holding clip in the origi- nal position. Tip hook the holding clip so that it contacts the filter guide projections. 8. Close the air filter case cover, and then tighten the quick fastener screw. To clean the air filter check hose...
Page 60
Periodic maintenance and adjustment 6-17 1 2 3 4 5 6 7 8 9 eau52460 adjusting the engine idling speed the engine idling speed must be checked and, if necessary, adjusted as follows. Tip a digital tachometer is needed to make this adjustment. 1. Position the digital tachometer at the ignition coil, w...
Page 61
Periodic maintenance and adjustment 6-18 2 3 4 5 6 7 8 9 eau21401 valve clearance the valve clearance changes with use, resulting in improper air-fuel mixture and/or engine noise. To prevent this from occurring, the valve clearance must be adjusted by a yamaha dealer at the intervals specified in th...
Page 62
Periodic maintenance and adjustment 6-19 1 2 3 4 5 6 7 8 9 tire inspection the tires must be checked before each ride. If the center tread depth reaches the specified limit, if the tire has a nail or glass fragments in it, or if the sidewall is cracked, have a yamaha dealer re- place the tire immedi...
Page 63
Periodic maintenance and adjustment 6-20 2 3 4 5 6 7 8 9 high-quality product. ride at moderate speeds after changing a tire since the tire surface must first be “broken in” for it to develop its optimal characteristics. Eau21943 spoke wheels warning ewa10610 the wheels on this model are not de- s...
Page 64
Periodic maintenance and adjustment 6-21 1 2 3 4 5 6 7 8 9 could be obtained as described above, skip steps 2–5. 2. Fully turn the adjusting bolt in di- rection (a) to loosen the clutch ca- ble. 3. Slide the rubber cover back further down the clutch cable, and then loosen the locknut. 4. To increase...
Page 65
Periodic maintenance and adjustment 6-22 2 3 4 5 6 7 8 9 sult in loss of control and an acci- dent. Eau44820 checking the shift pedal the operation of the shift pedal should be checked before each ride. If opera- tion is not smooth, have a yamaha dealer check the vehicle. Eau22273 brake light switch...
Page 66
Periodic maintenance and adjustment 6-23 1 2 3 4 5 6 7 8 9 eau22392 checking the front and rear brake pads the front and rear brake pads must be checked for wear at the intervals spec- ified in the periodic maintenance and lubrication chart. Eau22430 front brake pads each front brake pad is provided...
Page 67
Periodic maintenance and adjustment 6-24 2 3 4 5 6 7 8 9 rear brake warning ewa15990 improper maintenance can result in loss of braking ability. Observe these precautions: insufficient brake fluid may al- low air to enter the brake sys- tem, reducing braking performance. clean the filler cap bef...
Page 68
Periodic maintenance and adjustment 6-25 1 2 3 4 5 6 7 8 9 eau22760 drive chain slack the drive chain slack should be checked before each ride and adjusted if necessary. Eau52480 to check the drive chain slack 1. Place the motorcycle on the side- stand. Tip when checking and adjusting the drive chai...
Page 69
Periodic maintenance and adjustment 6-26 2 3 4 5 6 7 8 9 nuts to their specified torques. 4. Make sure that the drive chain pull- ers are in the same position, the drive chain slack is correct, and the drive chain moves smoothly. Eau23025 cleaning and lubricating the drive chain the drive chain must...
Page 70
Periodic maintenance and adjustment 6-27 1 2 3 4 5 6 7 8 9 eau23095 checking and lubricating the cables the operation of all control cables and the condition of the cables should be checked before each ride, and the ca- bles and cable ends should be lubricat- ed if necessary. If a cable is damaged o...
Page 71
Periodic maintenance and adjustment 6-28 2 3 4 5 6 7 8 9 clutch lever eau23183 checking and lubricating the brake pedal the operation of the brake pedal should be checked before each ride, and the pedal pivot should be lubricat- ed if necessary. Eau23202 checking and lubricating the sidestand the op...
Page 72
Periodic maintenance and adjustment 6-29 1 2 3 4 5 6 7 8 9 eaum1652 lubricating the swingarm pivots the swingarm pivots must be lubricat- ed by a yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart. Eau23272 checking the front fork the condition and operation o...
Page 73
Periodic maintenance and adjustment 6-30 2 3 4 5 6 7 8 9 eau23283 checking the steering worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be checked as fol- lows at the intervals specified in the pe- riodic maintenance and lubrication chart. 1. Place a s...
Page 74
Periodic maintenance and adjustment 6-31 1 2 3 4 5 6 7 8 9 skin, eyes or clothing and al- ways shield your eyes when working near batteries. In case of contact, administer the fol- lowing first aid. • external: flush with plenty of water. • internal: drink large quan- tities of water or milk and im-...
Page 75
Periodic maintenance and adjustment 6-32 2 3 4 5 6 7 8 9 eau52422 replacing the fuse the fuse is located under the seat. (see page 3-13.) if the fuse is blown, replace it as fol- lows. 1. Push the main switch to “off” and turn off all electrical circuits. 2. Remove the blown fuse, and then install a...
Page 76
Periodic maintenance and adjustment 6-33 1 2 3 4 5 6 7 8 9 1. Remove the headlight cowling to- gether with the headlight unit by removing the bolts and pulling up- ward as shown. 2. Disconnect the headlight coupler, and then remove the headlight bulb cover. 3. Remove the headlight bulb holder by tur...
Page 77
Periodic maintenance and adjustment 6-34 2 3 4 5 6 7 8 9 eau24181 tail/brake light this model is equipped with an led-type tail/brake light. If the tail/brake light does not come on, have a yamaha dealer check it. Eau24204 replacing a turn signal light bulb 1. Remove the turn signal light lens by re...
Page 78
Periodic maintenance and adjustment 6-35 1 2 3 4 5 6 7 8 9 eau24313 replacing the license plate light bulb 1. Remove the license plate light unit by removing the screws. 2. Remove the license plate light bulb socket (together with the bulb) by pulling it out. 3. Remove the burnt-out bulb by pull- in...
Page 79
Periodic maintenance and adjustment 6-36 2 3 4 5 6 7 8 9 4. Insert a new bulb into the socket. 5. Install the socket (together with the bulb) by pushing it in. 6. Install the headlight unit. Eau24350 supporting the motorcycle since this model is not equipped with a centerstand, follow these precauti...
Page 80
Periodic maintenance and adjustment 6-37 1 2 3 4 5 6 7 8 9 eau24360 front wheel eau49332 to remove the front wheel warning ewa10821 to avoid injury, securely support the vehicle so there is no danger of it falling over. 1. Remove the rubber cap, and then loosen the front wheel axle pinch bolts and t...
Page 81
Periodic maintenance and adjustment 6-38 2 3 4 5 6 7 8 9 8. Push down hard on the handlebar several times to check for proper fork operation. Eau25080 rear wheel eau45183 to remove the rear wheel warning ewa10821 to avoid injury, securely support the vehicle so there is no danger of it falling over....
Page 82
Periodic maintenance and adjustment 6-39 1 2 3 4 5 6 7 8 9 tip the drive chain does not need to be disassembled in order to remove and install the rear wheel. 7. While supporting the brake caliper, pull the wheel axle out. 8. Remove the drive chain pullers, spacers and the wheel. Notice: do not appl...
Page 83
Periodic maintenance and adjustment 6-40 2 3 4 5 6 7 8 9 eau25871 troubleshooting although yamaha motorcycles receive a thorough inspection before shipment from the factory, trouble may occur dur- ing operation. Any problem in the fuel, compression, or ignition systems, for example, can cause poor s...
Page 84
Periodic maintenance and adjustment 6-41 1 2 3 4 5 6 7 8 9 eau53122 troubleshooting charts starting problems or poor engine performance check the fuel level in the fuel tank. 1. Fuel there is enough fuel. There is no fuel. Check the compression. Supply fuel. The engine does not start. Check the batt...
Page 85
Periodic maintenance and adjustment 6-42 2 3 4 5 6 7 8 9 engine overheating warning ewat1040 do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Be sure to wait until the engine has coo...
Page 86: Motorcycle Care and Storage
7-1 1 2 3 4 5 6 7 8 9 motorcycle care and storage eau37833 matte color caution notice eca15192 some models are equipped with matte colored finished parts. Be sure to consult a yamaha dealer for advice on what products to use be- fore cleaning the vehicle. Using a brush, harsh chemical products or cl...
Page 87: Motorcycle Care and Storage
Motorcycle care and storage 7-2 2 3 4 5 6 7 8 9 off any detergent residue using plenty of water, as it is harmful to plastic parts. do not use any harsh chemical products on plastic parts. Be sure to avoid using cloths or sponges which have been in contact with strong or abrasive cleaning products...
Page 88: Motorcycle Care and Storage
Motorcycle care and storage 7-3 1 2 3 4 5 6 7 8 9 including chrome- and nickel-plat- ed, surfaces. 5. Use spray oil as a universal clean- er to remove any remaining dirt. 6. Touch up minor paint damage caused by stones, etc. 7. Wax all painted surfaces. 8. Let the motorcycle dry completely before st...
Page 89: Motorcycle Care and Storage
Motorcycle care and storage 7-4 2 3 4 5 6 7 8 9 stabilizer (if available) to prevent the fuel tank from rusting and the fuel from deteriorating. 3. Perform the following steps to pro- tect the cylinder, piston rings, etc. From corrosion. A. Remove the spark plug cap and spark plug. B. Pour a teaspoo...
Page 90: Specifications
8-1 1 2 3 4 5 6 7 8 9 specifications eau50975 dimensions: overall length: 2315 mm (91.1 in) overall width: 825 mm (32.5 in) overall height: 1275 mm (50.2 in) seat height: 960 mm (37.8 in) wheelbase: 1475 mm (58.1 in) ground clearance: 335 mm (13.19 in) minimum turning radius: 2400 mm (94.5 in) weigh...
Page 91: Specifications
Specifications 8-2 2 3 4 5 6 7 8 9 transmission type: constant mesh 5-speed operation: left foot operation gear ratio: 1st: 2.417 (29/12) 2nd: 1.733 (26/15) 3rd: 1.313 (21/16) 4th: 1.050 (21/20) 5th: 0.840 (21/25) chassis: frame type: semi double cradle caster angle: 27.00 trail: 115 mm (4.5 in) fro...
Page 92: Specifications
Specifications 8-3 1 2 3 4 5 6 7 8 9 tail/brake light: led front turn signal light: 12 v, 10.0 w 2 rear turn signal light: 12 v, 10.0 w 2 auxiliary light: 12 v, 5.0 w 1 license plate light: 12 v, 5.0 w 1 meter lighting: el (electroluminescent) neutral indicator light: 12 v, 1.7 w 1 high be...
Page 93: Consumer Information
9-1 2 3 4 5 6 7 8 9 consumer information eau48612 identification numbers record the vehicle identification num- ber and model label information in the spaces provided below for assistance when ordering spare parts from a yamaha dealer or for reference in case the vehicle is stolen. Vehicle identific...
Page 94: Index
Index a air filter element and check hose, cleaning .................................................6-14 auxiliary light bulb, replacing ...................6-35 b battery......................................................6-30 brake and clutch levers, checking and lubricating .......................
Page 95: Index
Index turn signal switch ...................................... 3-7 v valve clearance ....................................... 6-18 vehicle identification number..................... 9-1 w wheel bearings, checking ....................... 6-30 wheel (front) ...............................................
Page 96
1dx-9-e1.Book 4 ページ ２０１２年７月３１日 火曜日 午前９時３１分.
Page 97
U1dxe1_hyoshi.Indd 3 2012/08/08 17:42:01.
Page 98
Printed on recycled paper printed in japan 2012.08-0.4×1 ! (e) u1dxe1_hyoshi.Indd 4 2012/08/08 17:42:02.