Z-Wave ST814 Owner's Manual

Page of 8

Download

Print this page

Bookmark us

ST814

Temperature/Humidity Detector

The Temperature/Humidity Detector is a Z-Wave

enabled device which is fully

compatible with any Z-Wave

enabled network. Z-Wave

enabled devices

displaying the Z-Wave

logo can also be used with it regardless of the

manufacturer, and ours can also be used in other manufacturer’s Z-Wave

enabled networks. Inclusion of this detector on other manufacturer’s Wireless

Controller menu allows remote operation of connected modules when the

detector is triggered.

The Temperature/Humidity Detector is designed to monitor the current

temperature and humidity of ambient environment. The reading of

temperature/humidity can be reported to you on a regular base at your disposal.

If temperature/humidity reaches set points, the detector will send alerts to

associated devices for further execution. Since sudden temperature/humidity

change may cause health problems to people such as elderly or very young

children, Temp./Humid. Detector provides you most up-to-date temperature and

humidity reading for you to watch your family’s health.

Product Overview

LCD Screen

Function Keys

Select modes/Change setting

Select temperature unit/Linking

MAX/▲

Increase settings, displays max. temperature/humidity or

enable RF & beep tone

MIN/▼

Decrease settings, displays min. temperature/humidity or

disable RF & beep tone

Temperature/Humidity Sensor

Mounting Bracket

LCD Display

Include to or Exclude from a Z-Wave

Network

One of function key (

) is used to carry out inclusion, exclusion, association

and reset. When the detector is first powered up, the reading in RF mode is 00

which implies that it hasn’t been allocated a node ID and cannot work with

Z-Wave

enabled devices. The Temp./Humid. Detector will stay “awake” for

10 minutes when power is first applied to allow time for configuration. Please

get familiar with the terms below before starting the operations.

Function

Description

Inclusion

Add a Z-Wave enabled device (e.g.Temp./Humid Detector) to Z-Wave

network.

Exclusion

Delete a Z-Wave enabled device (e.g. Temp./Humid Detector) from the

network.

Association

After inclusion, you have to define the relationship between devices.

Trough association, device can be assigned as master/slave, and

specify which slave is going to be controlled by which master.

Reset

Restore Temp./Humid Detector to factory default.

The table below lists an operation summary of basic Z-Wave functions. Please

refer to the instructions for your Z-Wave

Certificated Primary Controller to

access the setup function, and to include/exclude/associate devices.

Function Description

LED

Indication

No node

The Z-Wave Controller does not

allocate a node ID to the detector.

The RF reading displays 00

(MODE 7)

1. Have Z-Wave Controller entered

inclusion mode.

Inclusion

2. Pressing key 3 times within

1.5 seconds will enter inclusion mode.

flashes

Front View

Side View

Rear View

Beep tone ON

Min.Temp./Humidity

Max.Temp./Humidity

Temperature °C/°F

Humidity %

Temp./Humid. OFF

Temp./Humid. ON

Linking Signal

Radio Frequency

Status

Low Battery

1 2 3 4 5 6 7 Next › »

Summary of ST814

Page 1
1 st814 temperature/humidity detector the temperature/humidity detector is a z-wave tm enabled device which is fully compatible with any z-wave tm enabled network. Z-wave tm enabled devices displaying the z-wave tm logo can also be used with it regardless of the manufacturer, and ours can also be us...
Page 2
2 2 3 4 1 5 function description led indication 1. Have z-wave controller entered exclusion mode. 2. Pressing key 3 times within 1.5 seconds will enter exclusion mode flashes exclusion node id has been excluded the rf reading displays 00 (mode 7) 1. Pressing key 3 times within 1.5 seconds will enter...
Page 3
3 note: after removing batteries, please wait for 5 seconds before replacing them. Operation there are 8 modes available for selection. Press to select desired mode for different settings. Mode function 1 current temperature display (°c/°f) 2 current humidity display (%) 3 setting for temperature tr...
Page 4
4 1.3 temperature trigger-off press and select mode 4 to enter setting of temperature trigger-off. Icon flashes and the screen shows the recorded trigger-off temperature. If no value is preset, the screen will display “ - - -。c ”. To adjust trigger-off value, press and hold for 5 seconds until a lon...
Page 5
5 note: the humidity of trigger-on and trigger-off cannot be set equal; there must be at least 5% difference in between. For example, if now the trigger-on humidity is already set to be 50%, so trigger-off humidity can only be 45% ≦ or ≧55%. (values between 45% and 55% cannot be set.) once the detec...
Page 6
6 sensor_multilevel_report [command class sensor multilevel, sensor multilevel report, sensor type = 0 x 01 (air temperature), precision+scale+size = 0 x 2a, sensor value 1 = (high byte of temperature value), sensor value 2 = (low byte of temperature value)] 1-1-3 low battery report when the battery...
Page 7
7 2-1 auto report 2-1-1 time interval the temp./humid. Detector can be set to emit report of current status to the nodes of grouping 1 automatically at a set time. The time interval can be set from 1 minute to 24 hours. For instance, if time interval is set in 1 minute, the detector will report its ...
Page 8
8 specifications operating frequency 868.42mhz (st814-1) / 908.42mhz (st814-2) operating temperature range -10℃ ~ 50℃ relative humidity range 20% ~ 90% temperature unit ℃ / ℉ battery type 1.5v x 3 alkaline/aa type battery operating range up to 30 meters line of sight (indoor) zdk version v5.02 *spec...