Z-Wave ST814 Owner's Manual - page 4
4
1.3 Temperature Trigger-OFF
Press
and select MODE 4 to enter setting of temperature trigger-OFF.
Icon
flashes and the screen shows the recorded trigger-OFF temperature. If
no value is preset, the screen will display “
- - -。C ”.
To adjust trigger-OFF value, press and hold
for 5 seconds until a long
beep is sounded. The “
- - -” starts flashing. Use
and
button to
adjust the degree of temperature, and hold
or
button to scan
through the temperature reading from -20。
C to 50。
C . Once the value is selected,
press
to confirm setting or press
to cancel.
To clear the trigger-OFF record, press both
and
at the same time.
The record is cleared after a long beep is sounded.
If the temperature reaches the preset trigger-OFF value, Temp./Humid. Detector
will emit RF signal. The screen of detector returns to MODE 1 and the icon
is flashing with backlight illumination and beep tone sounds for 1 second. Press
any key to stop the beep tone.
Note:
The temperature trigger-ON and trigger-OFF cannot be set equal; there MUST
be at least 2。C difference in between. For example, if now the trigger-OFF
temperature is already set to be 20。
C , so trigger-ON temperature can only be
≦18。C or ≧22。C (values between 18。C and 22。C cannot be set).
Once the detector has been triggered, the temperature must increase or cool
down at least 2。C from the preset value before it can be triggered again. For
example, if the detector is triggered on at 20。
C , then the temperature must be
≧22。C or ≦18。C before it can be re-triggered.
2. Humidity
2.1 Display of Current Humidity
Press
and select MODE 2 to display current humidity.
The humidity ranges from 20% RH to 90%RH. To show the last record of
max/min humidity, press
or
. To clear the record, press both
or
at the same time.
Threshold Limit Warning:
If the humidity is reaching the limit, the icon of MAX or MIN will be displayed on
the screen.
Humidity
Trigger-ON
Press
and select MODE 5 to enter setting of humidity trigger-ON. Icon
flashes and the screen shows the recorded trigger-ON humidity. If no value
is preset, the screen will display “
- - -%”.
To adjust trigger-ON value, press and hold
for 5 seconds until a long
beep is sounded. The “
- - -” starts flashing. Use
and
button to
adjust the percentage of humidity, and hold
and
button to scan
through the humidity reading from 20%RH to 90%RH. Once the value is
selected, press
to confirm setting or press
to cancel.
To clear the trigger-ON record, press both
and
at the same time.
The record is cleared after a long beep is sounded.
If the humidity reaches the preset trigger-ON value, Temp./Humid. Detector will
emit RF signal. The screen of detector returns to MODE 2 and the icon
is
flashing with backlight illuminate and beep tone sounds for 1 second. Press any
key to stop the beep tone.
2.3 Humidity Trigger-OFF
Press
and select MODE 6 to enter setting of humidity trigger-OFF. Icon
flashes and the screen shows the recorded trigger-OFF humidity. If no value
is preset, the screen will read
- - -%.
To adjust trigger-OFF value, press and hold
for 5 seconds until a long
beep is sounded. The “
- - -” starts flashing. Use
or
button to
scan through the humidity reading from 20%RH to 90%RH. Once the value is
selected, press
to confirm setting or press
to cancel.
To clear the trigger-OFF record, press both
and
at the same time.
The record is cleared after a long beep is sounded.
If the humidity reaches the preset trigger-OFF value, Temp./Humid. Detector will
emits RF signal. The screen of detector returns to MODE 2 and the icon
is
flashing with backlight illuminates and beep tone sounds for 1 second. Press any
key to stop the beep tone.