Z-Wave ZTS-110 User Manual

Other manuals for ZTS-110: User Manual

Manual is about: Z-Thermostat

Page of 20

Download

Print this page

Bookmark us

ZTS-110

Z-Thermostat

USER MANUAL

Printed in China

F820-8031-0003

2/11/14

Revised on 2/13/14

Revised on 2/14/14 V3.05

FCC Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Notice : Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user authority to operate the equipment.

Warnings

- Do not modify the unit in any way.

- Risk of fire.

- Risk of electrical shock.

- Risk of burns.

- Do not dispose of electrical appliances and unsorted municipal waste, use

separate collection facilities. Contact your local government for information

regarding the collection systems available.

- There is no user serviceable parts in this unit.

Caution

- Risk of explosion if battery is replaced by an incorrect type.

- Dispose of used batteries according to the instructions.

Revised on 3/6/14 V3.05

190x140mm folded to 95x140mm

1 2 3 4 5 6 7 Next › »

Summary of ZTS-110

Page 1
Zts-110 z-thermostat user manual printed in china f820-8031-0003 2/11/14 39 revised on 2/13/14 revised on 2/14/14 v3.05 fcc notice this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) thi...
Page 2
Table of contents introduction 2 features list 3 glossary 4 physical installation and wiring 5 installation location 6 6 wiring 7 jumper settings for electh-hpump and he-hg 9 10 10 10 11 11 12 17 18 18 20 23 23 25 26 26 check flirs / always listening mode in zts-110 28 28 36 37 38 39 39 physically i...
Page 3
Features list hvac system type compatible: - standard (gas/electric) or heat pump multistage system compatible: - standard hvac systems: 2 stage heating, 1 stage cooling - heat pump systems: 2 stage heating, 1 stage cooling heat pump change over valve: - selectable change over with cool or with heat...
Page 4
Physical installation and wiring read following scenarios carefully before you start as it matters to the battery life under z-wave operation: zts-110 can be powered by 4 x aa batteries, and/or 24vac c wire. A) if it is powered by batteries or powered by batteries first then applied with 24vac befor...
Page 5
Figure 5. Heat pump hvac system wiring figure 6. Non-heat pump 2-wires system wiring figure 7.Heat pump 2-wires system wiring thermostat should be powered by batteries and support heating control only. Thermostat should be powered by batteries and support heating control only. For heat pump output, ...
Page 6
9 10 jumper settings for electh-hpump and he-hg there are 6 jumpered pins on the thermostat circuit board that identify whether your system is: - gas or electric heater - non-heat pump or heat pump system you must ensure that these pins are set correctly for your system. The pin location is shown in...
Page 7
11 12 activate/deactivate easy mode the zts-110 is default with easy mode, below illustrates the functions of easy mode: - active functions: change mode, change fan mode and temperature scale selection - inactive functions: scheduling, program mode, clock display, setting time, setting swing, settin...
Page 8
13 14 if you deactivated the easy mode, you can continue to set up day, clock, 12/24 hour, f/c, swing and differential. Refer to below for steps: lcd indication step procedure / description press and hold "mode" key for 2 seconds to entry the setting mode. It will display "easy yes" if it stays in e...
Page 9
15 16 note: explanations of swing and differential set point heat mode: thermostat controls the temperature according to the following diagram o o o example for heating: (set point = 70 f, swing = 1 f, differential = 2 f) o o => 1st stage heater turns on when room temp is 69 f and off at 71 f. O o =...
Page 10
Change mode note: in heat mode =>it displays "heat" if electh is selected during jumper setting. => it displays "heat pump" if hpump is selected during jumper setting. Below example is based on heat pump lcd indication procedure / description press "mode" key once to change the operation mode: off -...
Page 11
Override/permanent override note: override/permanent override is only available in heat, cool or auto mode. Lcd indication step procedure / description press "prog" key once to select prog mode: override or permanent override at home page. 1 press up/down key to adjust set point temperature in heat ...
Page 12
Lcd indication step procedure / description press and hold "up" and "down" key for 2 seconds to disable / enable event during the time setting. If the event is disabled, "off" will be displayed. If the event is enabled, time will be displayed and hour will keep flashing. 5 wake mo tu we th fr wake a...
Page 13
Battery low indication defrost indication out of temperature range indication 23 24 lcd indication procedure / description zts-110 thermostat will detect the battery level every 30 minutes; battery low icon will be displayed at home page if the battery is running out. (user is required to change new...
Page 14
25 26 filter counter short cycle start up protection to protect the compressor / heat pump, those outputs forced off until 3minutes count down finished. Those outputs can be activated according to the room temperature after 3 minutes. Press and hold "mode" key to set the alert time for the filter us...
Page 15
Check flirs / always listening mode in zts-110 z-wave add (include) / delete (exclude) into/from z-wave network add (include) zts-110 to gateway / controller z-wave network note: after z-wave inclusion process, if you reset zts-110 to default while both 24vac and batteries are applied, zts-110 will ...
Page 16
Note: - it is recommended to perform the delete/exclude procedure before doing add/include. This is to make sure the zts-110 is not in any other z-wave network which will result in failure in inclusion process. - if the inclusion is failed, try exclusion, and/or reset zts-110 to factory default and ...
Page 17
31 32 z-wave configuration parameters different user has different preferred settings of their thermostat, you may use the below configuration parameters to change settings of corresponding functionality. 500 (0x01f4) to 4000 (0x0fa0) hours default = 500 (0x01f4) hours resolution = 100 (0x0064) hour...
Page 18
Parameter value range parameter no. Functions 0 (0x00) = disable auto report if room temperature is different from last report. Auto report if room temperature is different from last report. Delta change is >= o o 1 (0x01) = 1 f (0.5 c) o o 2 (0x02) = 2 f (1.0 c) o o 3 (0x03) = 3 f (1.5 c) o o 4 (0x...
Page 19
Reset zts-110 to factory default settings lcd indication step procedure / description press and hold "fan" + "mode" keys for 2 seconds to entry the reset mode. Press up/down key to toggle yes/no selection. 1 press "prog" key once to confirm the action. => it will perform the reset if select "yes" or...
Page 20
37 38 technical specifications model no. Bw8031us (zts-110us) bw8031au (zts-110au) bw8031eu (zts-110eu) rf frequency 908.4mhz (us) (zts-110us) 921.4mhz (au) (zts-110au) 868.4mhz (eu) (zts-110eu) rf operating distance up to 100ft outdoor line of sight, in unobstructed environment z-wave association g...