Z-World Wildcat BL2000 User Manual - page 94
90
Wildcat (BL2000)
plastic enclosure ................3, 68
attach BL2000 to base .........7
dimensions .........................70
power management ...............71
power supplies .......................71
backup-battery circuit ........73
battery backup ...................72
chip select circuit ...............76
switching voltage regulator 71
VRAM switch ...................74
power supply ...........................3
connections ....................8, 15
Program Mode .......................30
programming
flash vs. RAM ...................33
programming cable ..............3
programming port ..............23
programming cable .................3
connections ..........................8
DIAG connector ................84
programming port
pin configurations ..............85
pinout .................................84
used as diagnostic port ......84
R
Rabbit 2000
parallel ports ......................65
relay outputs ..........................20
reset .........................................8
hardware ..............................8
reset generator ...................75
RS-232 ..................................21
RS-485 ..................................21
RS-485 network ....................22
termination and bias resistors
Run Mode ..............................30
S
sample programs ...................35
A/D converter inputs
AD1.C ............................36
AD2.C ............................36
AD3.C ............................36
AD4.C ............................36
BOARD_ID.C ...................35
D/A converter outputs
DACAL.C ......................37
DAOUT1.C ...................37
DAOUT2.C ...................37
digital I/O
DIGIN.C ........................35
DIGOUT.C ....................35
LED.C ............................35
PWM.C ..........................36
RELAY.C ......................36
how to set IP address .........53
LEDS_4.C .........................35
PONG.C ............................11
serial communication
MASTER.C ...................36
PUTS.C ..........................36
SLAVE.C ......................36
TCP/IP ...............................53
PINGME.C ....................55
SMTP.C .........................56
SSI.C ..............................56
TELNET.C ....................56
serial communication ............21
programming port ..............23
RS-232 description ............21
RS-485 description ............21
RS-485 network ................22
resistors .........................23
serial ports
Ethernet port ......................24
setup ........................................7
base .................................7
tions .................................8
software ...................................4
A/D converter inputs
_anaIn ............................44
anaIn ..............................45
anaInCalib .....................44
anaInEERd .....................46
anaInEEWr ....................46
anaInVolts .....................46
board initialization ............39
brdInit ............................39
D/A converter outputs
anaOut ...........................48
anaOutCalib ...................47
anaOutEERd ..................49
anaOutEEWr .................49
anaOutVolts ...................49
digital I/O
digIn ...............................41
digOut ............................41
LED outputs
ledOut ............................43
libraries ..............................30
BL2000 ..........................38
RS232.LIB .....................42
TCP/IP ...........................38
relay output
relayOut .........................43
sample programs ...............35
LEDS_4.C .....................35
PONG.C ........................11
serial communication
flow control ...................42
ser485Rx ........................42
ser485Tx ........................42
watchdog timeout
chkWDTO .....................75
specifications
BL2100
header footprint .............61
headers ...........................61
dimensions
plastic enclosure ............70
dimensions BL2000 ..........58
electrical ............................59
temperature ........................59
spectrum spreader .................31
subsystems ......................13, 14
T
TCP/IP connections ...............51
10Base-T Ethernet card .....51
additional resources ...........56
Ethernet hub ......................51
steps ...................................51
technical support ...................11
Tool Kit ...................................3
AC adapter ..........................3
DC power supply .................3
Demonstration Board ..........3
Dynamic C software ............3
plastic enclosure ..................3
programming cable ..............3
software ...............................3
User’s Manual .....................3
wire assembly ......................3
V
Vcc