- DL manuals
- Zanussi
- Hob
- ZGG 642
- Instruction Booklet
Zanussi ZGG 642 Instruction Booklet
Summary of ZGG 642
Page 1
Gas hobs zgg 642 zgg 782 instruction booklet please read this instruction booklet before using the appliance gb.
Page 2: Important Safety Information
2 important safety information you must read these warnings carefully before installing or using the hob. If you need assistance, contact our customer care department on 08705 727727 installation z this appliance must be installed and serviced by a competent person as stated in the gas safety ( inst...
Page 3: Contents
3 contents for the user for the installer important safety information 2 description of the hob 4 operation 5 maintenance and cleaning 6 something not working? 7 service and spare parts 7 guarantee/customer service 16 european guarantee 17 important safety requirements 9 installation 10 building in ...
Page 4: Description of The Hob
4 description of the hob 1 1 2 3 4 2 1 3 1 1 4 zgg 642 zgg 782 1. Semi-rapid burners 2. Rapid burner 3. Auxiliary burner 4. Control knobs 1. Semi-rapid burners 2. Triple crown burner 3. Auxiliary burner 4. Control knobs.
Page 5: Operation
5 operation hob burners to light a burner: z push in the relevant control and turn it to maximum position; z then adjust the flame as required. Z if the burner does not ignite, turn the control knob to zero, and try again. If you use a saucepan which is smaller than the recommended size, the flame w...
Page 6: Maintenance and Cleaning
6 maintenance and cleaning before any maintenance or cleaning can be carried out, you must disconnect the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The hob top regularly wipe over the hob top a...
Page 7: Something Not Working?
7 something not working? If the hob is not working correctly, please carry out the following checks before contacting your local service force centre. Important: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made e...
Page 8: Engineers Technical Data
8 overall dimensions zgg 642 zgg 782 width: 580 mm. 680 mm. Depth: 510 mm. 510 mm. Cut out dimensions zgg 642 zgg 782 width: 550 mm. 560 mm. Depth: 470 mm. 480 mm. Supply connections gas: rc 1/2 inch (1/2 inch male) rear right hand corner electric: 230 v 50hz supply, 3 core flexible cable with non r...
Page 9: Provision For Ventilation
9 important safety requirements this hob must be installed in accordance with the gas safety (installation and use) regulations (current edition) and the iee wiring regulations (current edition). For appliances installed in the republic of ireland please refer to nsai- domestic gas installation i.S....
Page 10: Cut Out Size
10 cut out size the dimensions of the cut-out are given in the diagram. 550 47 0 30 rectangular cut-out size for hob dimensions are given in mm. Fo 2038 fo 2098 zgg 642 zgg 782 a) end of shaft with nut b) washer c) elbow fo 0814 fo 0264 installation important this hob must be installed by a competen...
Page 11: Building In
11 building in on/off switch flex outlet on/off switch flex outlet fo 0763 fo 0764 dimensions are given in mm. Fo 1013 3 building over a cupboard or drawer if the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the und...
Page 12: Electrical Connections
12 ) electrical connections any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. This hob must be earthed. The manufacturer declines any liability should these safety measures not be observe...
Page 13: Wiring Diagram
13 a. Ignitor switch b. Ignitor unit b l n 0 1 2 3 4 5 6 220/240 a wiring diagram fault finding preliminary electrical systems check a. Earth continuity check - appliance must be electrically disconnected - meter set on Ω (ohms) x 1 scale and adjust zero if necessary. A) test leads from any applianc...
Page 14
14 ignition system / gas ignition yes check plug top fuse and replace if necessary check polarity and earth continuity of supply point check earth continuity of appliance ignitor does not spark check fitting of burners check position of the electrode check by pass simmer adjusted light burner manual...
Page 15: Commissioning
15 commissioning when the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - turn the gas tap to the max position and ignite. - set the gas tap to the min flame position then turn the control knob from min to max several ti...
Page 16: Guarantee/customer Service
16 guarantee/customer service standard guarantee conditions we, zanussi-electrolux, undertake that if within 12 months of the date of the purchase this zanussi-electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option...
Page 17: European Guarantee
17 this appliance is guaranteed by electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move w...
Page 18
18.
Page 19
19.
Page 20
Grafiche mdm - forlì 35668-9204 11/06 www.Zanussi-electrolux.Co.Uk.