Zartek CDP-801 Instruction Manual - page 3
1. Place the caller unit and handset close to each other within a distance of 1m.
2. With the handset in switch off mode, press and hold Power ON/OFF button 12 and
door lock open button 13 together for around 3 sec to enter pairing mode. The LCD
will become backlighted and show a flashing letter “ ”.
3. Press and hold the pairing button 7 at back of caller unit while installing the alkaline
batteries. The call indicator 4 will start flashing after 3 sec, showing that the caller unit
has entered pairing mode.
Perform same for the caller unit that is intended to be used in backgate.
4. Now release the pairing button 7 , press call button 1 on the frontgate caller unit
(DO NOT press call button on the backgate caller unit) . Two “Di Di” sound will be heard
and at the same time, the letter “ ” and (or in case there is a backgate caller
unit) will show steady in LCD of handset once pairing is successful. The call indicator
4 on both frontgate & backgate caller unit should stop flashing and remain steady on.
5. Long press the Power ON/OFF button 12 to switch off handset. Take out the alkaline
batteries from caller unit and then re-install again or connect to the 12V DC supply.
6. The doorphone is now ready for operation.
If the pairing process is not successful ( the “ ” continues to flash in LCD of handset), repeat
the procedures from step 1 again.
N.B. In case you are having two or more handsets as well as backgate caller unit, always
perform pairing process with all caller units and handsets together and with the handsets
being set in pairing mode first.
Remember every time you add on new units to the system, either handset or caller unit (for
backgate use), it is necessary to perform the pairing process all over again with all the units
together or otherwise the new units will not work with your original system.
6
5
Location:
Select a suitable place for the gatestation such as on a gooseneck or wall. The mounting
plate should be fitted on a flat wall surface so the provided screws will fix properly. It is very
important that the gatestation is not embedded into a wall or covered by any metal rain shield
or cover. Wireless radio signals will be blocked by concrete or metal so for maximum range,
use a gooseneck with the smallest metal backing plate. For maximum range it is also
recommended not to mount the gatestation near other electronic equirment.
Power:
Connection the 12v DC supply ( provided power supply) or from a gatemotor to the terminals
at the back of the gatestation . A connector with plug has been provided for your
convenience to be able to disconnect easily. If the provided power supply is not used, it is still
recommended to use the plug which must be cut off the power supply.
Gate triggering can only be done if there is a 12v supply connected.
There are 3 trigger output connections. Points A,C give a 12v output and A,B a 0v when triggered
and . It is recommended using the provided relay board which will protect and
isolate the gatestation from any surges. The relay board POS and NEG connections should
be linked to the points A,C and the LED on the relay will light when the gatestation is triggered
from the handset. Connect the COM and N.O. points on the relay board to the COM and TRG
points on the gate controller board.
Where DC supply is available, the call button 1 will be automatically illuminated once
the environment gets dark. This feature and electric door latch opening feature will not operate
when using alkaline batteries so as to keep long battery life.
CAUTION : When using DC supply, in case the electric door latch does not function, reverse
the polarity connected to and try again.
C.
Mounting of Caller Unit
Driled holes
INSERT RIVERTS INTO HOLES
(FOR CONCRETE WALL ONLY)
B.
Pairing the Handset and Caller unit
This process is to match the caller unit with handset so that they can communicate with each
other while no other devices (even doorphone of identical model) can interfere with you or
receiving your signal.
The caller unit and handset are already paired with factory preset code when they are
shipped from factory. However, we recommend you perform pairing again to achieve better
privacy and to avoid false triggering of door lock from nearby doorphone system.
To perform pairing process, it is necessary to use alkaline batteries as power supply in the
caller unit while the12V DC supply should be disconnected temporarily.
8
Hold in
for 3 sec.
Press in whilst
inserting batteries