Zelmer 32z012 User Manual - page 34
38
32Z012-002_v05
Do not immerse the motor housing (10) in
water or other liquid.
●
Do not clean the outside of the housing
(10)
with
aggressive detergents such as emulsion milk or pastes,
etc. They can remove information graphic symbols.
●
Do not clean the transparent jug
(9)
with harsh sponges
or clothes.
●
After washing dry thoroughly all the parts of the
appliance.
Cutting unit disassembling
●
Unplug from the mains supply outlet.
●
Empty the jug
(9)
.
●
Remove the lid
(8)
from the blender jug
(9)
. Turn the
blender jug
(9)
„upside down” and place on the flat and
firm surface.
●
Turn the blocking ring counter clockwise. Remove
carefully with a gasket.
The cutting blades are sharp. Handle them
carefully.
Cutting unit assembling
●
Turn the blades upside down in order to assemble them
and insert at first the gasket at the jug opening flange
(9)
and blades inside the jug
(9)
.
●
Insert blocking ring and turn it clockwise until it runs.
Make sure that the blocking ring is screwed to the jug
(9)
.
It influences the tightness of the connection.
●
After assembling, turn the jug
(9)
upside down and place
it on the motor housing
(10)
so, that the protrusions in
bottom part of the jug
(9)
are fitted with the protrusions
top part of the motor housing
(10)
.
The handle of the blender jug
(9)
shall be placed on the right
side of the appliance.
Ecology – environment protection
Each user can protect the natural environment. It is neither
difficult nor expensive.
In order to do it: put the cardboard packing into
recycling paper container; put the polyethylene
(PE) bags into container for plastic.
When worn out, dispose the appliance to
particular disposal centre, because of the
dangerous elements of this appliance, which
can be hazardous for natural environment.
Do not dispose the appliance with the municipal waste!
12
ICE function
●
Check if the stand blender is clean, before you use it for
crushing ice. Otherwise wash it thoroughly with clean
water. Any residues of washing agent can influence the
taste of crushed ice and shall cause that the drink we
add the ice to, shall loose its taste.
●
In case you want to crush ice, use 6 to 10 ice cubes
(max. 2 cm) in given time, and then add 15 ml (1 spoon)
fresh cold water.
●
Assemble the lid
(8)
including overlay
(7)
on the appli-
ance and press ICE switch.
ICE feature operates for 30 seconds, then the
appliance switches off automatically.
Do not try to crush the ice without adding some
water into the jug.
Press the lid (8) with one hand during ICE
feature is on.
After operation
To switch off the stand blender press and hold ON/OFF
switch for 3 seconds, until the blue highlight around the
control panel
(11)
is off.
●
Hold the motor unit
(10)
with one hand, catch the jug
handle with the other hand and remove it from the motor
unit
(10)
turning it counter-clockwise.
●
Remove the lid
(8)
from the jug
(9)
.
●
Unplug the appliance from the mains supply outlet when
it is not in use.
Cleaning and maintenance
Clean after operation as soon as possible,
to prevent the pulp accumulation inside the
jug (9).
1
Pour approximately 1 liter of water to the blender jug
(9)
and start-up the appliance for approximately 30 seconds and
hold the CLEAN/PULSE button.
2
Then empty the blender jug
(9)
, turn it upside-down
and dry.
3
If necessary, clean the jug
(9)
, lid
(8)
, feeder opening
stopper
(7)
and blades
(14)
in warm water with wash-up
liquid.
●
Then rinse it under clean running water and dry.
●
If you left the jug for longer time without cleaning and
some particles glued to the jug inner, use nylon brush.
●
We do not recommend cleaning the jug
(9)
, blades
(14)
,
lid
(8)
and feeder opening stopper
(7)
in dish washer.
Aggressive cleaning agents applied in such device can
influence negative the surface conditions.
4
Clean the outsider of the motor housing
(10)
with damp,
gentle cloth.
C
The manufacturer does not accept any liability for any damages
resulting from unintended use or improper handling.
The manufacturer reserves his rights to modify the product any time
in order to adjust it to law regulations, norms, directives, or due to
construction, trade, aesthetic or other reasons, without notifying in
advance.