Zelmer 332.2 User Manual - page 26
27
The manufacturer/importer does not accept any liability for any
damages resulting from unintended use or improper handling.
The manufacturer/importer reserves his rights to modify the product
any time in order to adjust it to law regulations, norms, directives,
or due to construction, trade, aesthetic or other reasons, without
notifying in advance.
Preparation of the electric kettle for
operation
Before the irst use, wash the kettle inside (for washing
instructions see “Cleaning and maintenance”), ill it with
water up to the “max” level, and let it boil four times (use
fresh water each time) and wash again.
Operating instructions of the electric kettle
(Fig. B)
1
Open the lid
(5)
.
2
Place the ilter
(11)
in the kettle – if it was taken out
before.
3
Fill the kettle up with the desired amount of water (the
level is visible on the indicator
(7)
).
WARNING! Do not boil the water if it is below the
minimum level or beyond the maximum level on the
indicator (7).
4
Close the lid.
5
Place the kettle on the power base
(12)
.
6
Put the plug of the connecting cord into a mains socket
with an earth pin – the upper part of the kettle body will
light up.
7
Turn on the ketttle by pressing the switch button into
position I – the indicator light will come on.
8
The kettle switches off automatically when the water
has reached the boiling point, the lever switch returns to its
starting position – the light comes off.
If further use of the kettle is anticipated, it is not necessary to
remove the plug of the connecting cord from the power socket.
WARNING! Be careful not to ill up with water beyond
the nominal capacity when pouring water into the
kettle.
The rising of the water level in the kettle is delayed in relation
to the speed of pouring the water. It is caused by the ilter
slowing down the speed of the low. This can be prevented by
pouring the last portions of water extremely carefully before
the water reaches the maximum level on the indicator.
In the event that an empty kettle is switched on, it will be
switched off by a thermal device automatically.
In order to switch the kettle on again after it has cooled down
(approx. 15 minutes), take it off the base, replace it and
switch the kettle on by pressing the lever
(8)
. The cooling
down of the kettle can be accelerated by puring cold water
into the kettle.
Cleaning and maintenance
(Fig. C)
WARNING! Always clean a cold kettle!
1
Remove the plug of the connecting cord from the power
socket.
2
Take out the ilter
(11)
.
3
Clean the outside surfaces with a soft cloth moistened
with washing-up liquid.
In order to remove the build-up of hard water ilm from the
outside and inside walls of the kettle, wipe them with a cloth
moistened with vineger.
4
Rinse the kettle with fresh water.
Filter replacement – descaling
In the event that scale builds up on the bottom of the kettle,
it needs to be removed. 6% or 10% vinegar is used for this
purpose.
Open the lid
(5)
.
Take out the ilter
(12)
.
Wash the ilter under running water.
Pour in 0.5 l of vinegar and switch on the kettle
(8)
.
Boil the vinegar and leave in the kettle for about 30
minutes.
Pour the vinegar out and rinse the kettle with fresh
water.
Fill the kettle up with fresh water, boil the water and pour
it out after is has boiled.
Repeat the above procedure if there still is scale on the
bottom.
When the procedure is inished, replace the iter
(11)
in
the kettle, following the procedure of taking the ilter out
in reverse order.
WARNING! Negligence in descaling the kettle may
results in its damage.
Ecology – environment protection
Each user can protect the natural environment. It is neither
dificult nor expensive.
In order to do it: put the cardboard packing into
recycling paper container; put the polyethylene
(PE) bags into container for plastic.
When worn out, dispose the appliance to
particular disposal centre, because of the
dangerous elements of this appliance, which
can be hazardous for natural environment.
Do not dispose into the domestic waste disposal!!!