3M Wireless Tire Pressure Monitoring System Operation Manual - page 8
Mode IV-3
Arbitrary tire location rearrangement:
the " 4 " displayed at the lower right corner means the system is now in Mode IV
A green light indicator is displayed at Tire No. 3, and the " 3 " displayed aside indicates you're setting up the location for sensor
No. 3. Next, please deflate tire No. 3 to a pressure value lower than 26 psi. The pressure value is now displayed at Tire No.
3, along with a red light indicator. Then, please inflate tire No. 3 to a normal pressure value (no less than 26 psi and no greater
than the recommended normal pressure value). The normal pressure value is now displayed at Tire No. 3, along with a green
light indicator. The " 4 " displayed at the lower right corner means the system is now in Mode IV. If sensor No. 3 remains at
the same position and needs no reconfiguration, please press the Setup button during Process 1 of Mode IV-3 to skip configuration
of sensor No. 3 and enter Mode IV-4 (as illustrated in Process 1 of Mode IV-4). The screen will pause for 2 seconds and then
automatically enter Mode IV-4
Arbitrary tire location rearrangement:
the " 4 " displayed at the lower right corner means the system is now in Mode IV
A green light indicator is displayed at Tire No. 4, and the " 4 " displayed aside indicates you're setting up the location
for sensor No. 4. Next, please deflate tire No. 4 to a pressure value lower than 26 psi. The pressure value is now displayed
at Tire No. 4, along with a red light indicator. Then, please inflate tire No. 4 to a normal pressure value (no less than 26
psi and no greater than the recommended normal pressure value). The normal pressure value is now displayed at Tire
No. 4, along with a green light indicator. The " 4 " displayed at the lower right corner means the system is now in Mode
IV. If sensor No. 4 remains at the same position and needs no reconfiguration, please press the Setup button during
Process 1 of Mode IV-4 to skip configuration of sensor No. 4 and complete the setup procedure for Mode IV. The screen
will pause for 2 seconds, then automatically exit the Tire Switching Mode and go back to normal display mode.
Mode IV-4
Process 1** Process 2** Process 3** Process 4
Process 1** Process 2** Process 3** Process 4
Process 1** Process 2** Process 3** Process 4
Mode V
Single sensor replacement (e.g., sensor No.1 is damaged and needs replacement):
the " 5 " displayed at the lower right corner
means the system is now in Mode V
Step 1: A green light indicator is displayed at Tire No. 1, and the " 1 " displayed aside indicates you're going to replace sensor
No. 1.
Step 2: Next, please deflate tire No. 1 to a pressure value lower than 26 psi. The pressure value is now displayed at Tire No.
1, along with a red light indicator. Then, please inflate tire No. 1 to a normal pressure value (no less than 26 psi and no greater
than the recommended normal pressure value). The normal pressure value is now displayed at Tire No. 1, along with a green
light indicator. The " 5 " displayed at the lower right corner means the system is now in Mode V.
The screen will pause for 2 seconds, and then the system will automatically exit the Single Sensor Replacement Mode and go
back to normal display mode.
NOTE: If the sensor needing replacement is located on tire No. 2, please press the Setup button during
step 1 to skip from sensor No.1 to sensor No. 2. The same rule applies to the rest of the sensors.
Warning
1. The wireless receiver and display unit's power being turned off or its power cord being disconnected during automatic
tire location adjustment mode will result in system configuration failure. However, after the power is restored, the
system will resume tire monitoring tasks according to previous settings.
2. After the system setup procedure is completed, please first test whether the system can receive information from 4
tires correctly. If not, please strictly follow the foregoing steps to reconfigure the system (at this stage, you may reference
the " How to Replace the Consumables in the Wireless Tire Sensor and Emitter Unit " section to conduct single sensor
replacement).