- DL manuals
- A-Neuvideo
- Switch
- HD-44G
- Instruction Manual
A-Neuvideo HD-44G Instruction Manual
Summary of HD-44G
Page 1
Audio / video manufacturer hd-44g 4x4 hdmi matrix switcher v2.0 instruction m anual a-neuvideo.Com frisco, texas 75034 (317) 456-2461.
Page 2
Safety information 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fi...
Page 3
Table of contents a neu video 1 contents introduction & package contents ...............................1 features & specifications .................................................2 front panel .............................................................................3 rear panel ..................
Page 4
2 features & specifications features • 4x hdmi digital source devices matrix switched to 4x hdmi devices • hdmi digital video w/embedded audio, dvi format and cec/hdcp 2.0 compliant • (7) function key control and worldwide edid modes for hdtv resolutions • link speeds of up to 6.75 gbps (link clock ...
Page 5
3 front panel front panel q power switch: the power switch turns the unit on and off. The led will illuminate red to indicate that the switcher is on and is receiving power. The switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration wi...
Page 6
4 front panel front panel o function key - off disables (mute) video to selected channels. Either destinations. - press off button followed by any destination channel. - press 1 thru 4 output destination. The display will show ” 0 “ for the selected channel indicating no video selected. A function k...
Page 7
5 front panel front panel d function key - memory the system will show store presets, up to a total of (8). Presets are stored in local memory using source keys 1 thru 4 or destination keys 1 thru 4 as the memory preset location. - configure desired matrices.. - press memory button. - press 1 thru 4...
Page 8
6 rear panel rear panel a neu video q dc power inlet: the switcher is fitted with a dc power plug input connector. Ensure that the used is of an approved type and is of sufficient current carrying connector capacity with the correct voltage and connector polarity. 12volt dc power supply 3a max (cent...
Page 9
7 typical application installing diagram sample connection using rs-232 serial interface or ir external in to control switch (hd-44g). Note: 1. Control projector over cat5e/6/7 extender: hd-6335t: hdbaset™ hdmi cat5e/6/7 transmitter hd-6335r: hdbaset™ hdmi cat5e/6/7 receiver 2. Preview output : pict...
Page 10
8 typical application installing diagram sample connection using audio extractor to audio amplifier and arc control box link tv return audio to audio device, control a satellite receiver source via hdbaset™ transmitter (hd-6335t) and hdbaset™ receiver (hd-6335r). Note: 1. Control satellite receiver ...
Page 11: Q W
9 remote control before making any connections to the switcher. Observe the following: • ensure the mains voltage supply matches the label on the supplied plug-pack (+/- 10%) • ensure that the power switch is off • ensure that all system grounds (earth) are connected to a common point. • avoid power...
Page 12
10 remote control ir remote custom and data codes (nec standard) how to setup ir codes : model number : hd-44g custom code : 837c power on : 837c a15e power off : 837c a25d all : 837c b04f off : 837c b14e edid : 837c b748 lock : 837c b54a recall : 837c b24d memory : 837c b44b enter : 837c b34c press...
Page 13
11 ir extender a neu video note: the external ir jack has voltage on the “ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka: stereo plug). Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off. *** when you plug the exte...
Page 14
Pin configuration: ani-101 and ani-101c transmitter pin configuration 1. Ani-101 ir 300m transmitter device cable (3c) ir transmitter (ani-101) ani-101 maximum distance ~ 984 feet (300m) ani-101c maximum distance ~ 6 feet (2m) ani-101 ir transmitter set r ohs /95/e c dc 12v ir out from receiver ir i...
Page 15
13 edid function edid function setup edid setup to change the edid setup step 1. Press the edid button the display will show the currently selected edid mode step 2. Press source #1 or #2 button row the button will flash blue and the display will show the current embedded edid status. Step 3. Press ...
Page 16
14 edid function edid function : 7x embedded edid modes mode 1. Fss ® (fast speed start) fast speed start mode shortens the startup time of the switcher. Selecting this mode does not force the edid setup to be cancelled. Users may first select one edid mode from mode 2 to 3, and then select mode 1 f...
Page 17
15 edid function edid function : learning learning edid single to single example : learn destination #4 edid to source #3. Step 1. Press the edid button the button will flash blue and the display will show the current embedded edid status. Step 2. Press the destination #4 button row copy the destina...
Page 18
16 ethernet & rs-232 serial interface ethernet serial interface connect a pc or control system. Version compatible v2.0 for a complete list of commands, please reference external document extended ethernet protocol instruction manual. Example of the commanded string to route input 3 to output 4 outp...
Page 20
End of document 18 terms and conditions of use please read the following terms and conditions carefully before using this hardware, components and software provided by, through or under a-neuvideo, inc (collectively, the “product”). By using installing or using the product, you unconditionally signi...