- DL manuals
- A-Neuvideo
- Switch
- HD-44G
- Instruction Manual
A-Neuvideo HD-44G Instruction Manual
Summary of HD-44G
Page 2
Safety information 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fi...
Page 3
Table of contents contents introduction & package contents ....................1 features & specifications ......................................2 front panel .................................................................3 rear panel ..................................................................
Page 4
Features features • 4x hdmi digital source devices matrix switched to 4x hdmi devices • hdmi digital video w/embedded audio, dvi format and cec/hdcp 2.0 compliant • seven (7) function key control and worldwide edid modes for hdtv resolutions • link speeds of up to 6.75 gbps (link clock rate of 225mb...
Page 5
3 front panel front panel 1 power switch the power switch turns the unit on and off. The led will illuminate red to indicate that the switcher is on and is receiving power. The switcher will remember that last state during a power cycle. When power is removed and resorted, the last confi guration wi...
Page 6
4 front panel front panel 9 function key - off disables (mute) video to selected channels. Either destinations. - press off button followed by any destination channel. - press 1 thru 4 output destination. The display will show ” 0 “ for the selected channel indicating no video selected. 10 function ...
Page 7
5 front panel front panel 12 function key - memory the system will show store presets, up to a total of 8. Presets are stored in local memory using source keys 1 thru 4 or destination keys 1 thru 4 as the memory preset location. - confi gure desired matrices.. - press memory button. - press 1 thru 4...
Page 8
6 rear panel rear panel power jack: dc jack - inner od ᴓ 2.1mm (+ ) outside od ᴓ 5.5mm (gnd) power input - 12vdc, 3a ir extender jack: female jack - inner od ᴓ 3.5 mm remote port : d-sub-9pin female connector hdmi digital video/audio connector: hdmi female connector. Note: with the proper adapters, ...
Page 9
Typical application installing diagram sample connection using rs-232 serial interface or ir external in to control switch (hd-44g). Note: 1. Control projector over cat5e/6/7 extender: hd-6335t: hdbaset hdmi cat5e/6/7 transmitter hd-6335r: hdbaset hdmi cat5e/6/7 receiver 2. Preview output : picture ...
Page 10
Typical application installing diagram sample connection using audio extractor to audio amplifi er and arc control box link tv return audio to audio device, control a satellite receiver source via hdbaset transmitter (hd-6335t) and hdbaset receiver (hd-6335r). Note: 1. Control satellite receiver ove...
Page 11
Remote control before making any connections to the switcher. Observe the following: > ensure the mains voltage supply matches the label on the supplied plug-pack (+/- 10%) > ensure that the power switch is off > ensure that all system grounds (earth) are connected to a common point. > avoid powerin...
Page 12
Remote control ir remote custom and data codes (nec standard) how to setup ir codes : model number : hd-44g custom code : 837c power on : 837c a15e power off : 837c a25d all : 837c b04f off : 837c b14e edid : 837c b748 lock : 837c b54a recall : 837c b24d memory : 837c b44b enter : 837c b34c press tv...
Page 13
Ir extender 11 sb-100 maximum distance ~ 984 feet (300 meters) sb-100 and sb-100c receiver pin configuration vcc (ring) signal (center) gnd (sleeve) tip ring sleeve tip: signal ring :vcc sleeve: gnd ring tip (center) sleeve inp ut dc 12v r ohs/95/ec ir ext . Rs - 232 r s -232 ir e xt. In sb-100 ir r...
Page 14
Ir extender 12 r ohs/95/ec dc 12v ir out from receiver ir in to receiver cat6/6a/7 output r ohs/95/ec dc 12v ir out from receiver ir in to receiver cat6/6a/7 output ir emitter: sb-101 maximum distance ~ 984 feet (300 meters) pin configuration: sb-101 and sb-101c transmitter pin configuration sb-101 ...
Page 15
Edid function edid function setup edid setup to change the edid setup step 1. Press the edid button the display will show the currently selected edid mode step 2. Press source #1 or #2 button row the button will fl ash blue and the display will show the current embedded edid status. Step 3. Press th...
Page 16
Edid function note : the already learned edid cannot be modifi ed. You can only rebuild a new learning edid. For example: when the source has “learned” the edid data from a destination, it will save that edid information into eprom and the edid data cannot change. Please select new learning destinat...
Page 17
Edid function edid function : learning learning edid single to single example : learn destination #4 edid to source #3. Step 1. Press the edid button the button will fl ash blue and the display will show the current embedded edid status. Step 2. Press the destination #4 button row copy the destinati...
Page 18
Rs-232 serial interface rs-232 serial interface connect a pc or control system. Version compatible v1.0 & v1.5 for a complete list of commands, please reference external document extended rs-232 protocol instruction manual. Rs-232 confi guration rs-232 cable is a straight thru cable and not null-mod...
Page 19
17 ethernet serial interface ethernet serial interface connect a pc or control system. Version compatible v2.0 for a complete list of commands, please reference external document extended ethernet protocol instruction manual. Ethernet serial interface pin ethernet reference 1 txop tx + 2 txon tx - 3...
Page 20
18 end of document terms and conditions of use please read the following terms and conditions carefully before using this hardware, components and software provided by, through or under a-neuvideo, inc (collectively, the “product”). By using installing or using the product, you unconditionally signi...