Qld office: 17 oasis court clontarf 4019 (07) 3883 0200 nsw office: 34-36 marigold street revesby 2212 (02) 9722 5555 vic/tas office: 147-153 canterbury road kilsyth 3137 (03) 9237 7766 b&d doors new zealand: 70 allens road easttamaki auckland, new zealand (09) 273 8600 www.Bnd.Co.Nz sa office: 23 f...
1 table of contents safety rules: 1 door types: 2 tools needed: 2 hardware provided: 2 before you begin: 2 completed installation: 2 assembly 3-4 assemble the rail: 3 install the chain/belt: 3 insert chain/belt into rail: 3 attach trolley to rail: 3 fasten rail to opener and install chain/belt: 3 at...
2 door types a. One-piece door with horizontal track only b. Sectional door with curved track: see page 5 – connect door arm to trolley. C. J-style tilt door / one-piece door without track a b c tools needed 2 1 11mm, 13mm 11/13mm 10mm, 8mm, 4,5mm, 4mm hardware provided (1) hex bolt (4) (2) clevis p...
3 assembly section assemble the rail grease inside edges of rail brace sections using grease (1). Place rail pieces (2) on flat surface for assembly. All four rail sections are interchangeable. Slide rail brace (3) onto rail section. Connect rail by sliding rail brace onto next rail section. Tap rai...
4 attach sprocket cover place sprocket cover (1) on top of the opener (2), secure with screws (3). Install the trolley stop bolt (4), use the lock nut (5) provided. Assemble header sleeve thread spring nut on carriage bolt until finger tight. Insert a screwdriver tip (1) into one of the slots of the...
5 attach rail to header bracket position opener on garage floor below the header bracket. Use packing material to protect the cover. Raise rail until holes in the header sleeve and holes in the header bracket align. Join with clevis pins (1). Insert ring fasteners (2) to secure. Note: to enable the ...
6 j-style tilt door / one-piece door without track • with the door fully open and parallel to the floor, measure the distance from the floor to the top of the door. • using a stepladder as a support, raise the top of the opener to this height. • the top of the door should be level with the top of th...
7 fasten door bracket follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement brace should be long enough to be secured to two or three vertical supports. A vertical reinforcement brace should cover the height of the top panel. Figu...
8 connect door arm to trolley a. Sectional door installation: close garage door and disengage the trolley as described in a. Slide trolley about 50mm from door. Connect straight door arm (1) to trolley door arm connector hole with a clevis pin (6). Secure with a ring fastener (7). Fasten curved door...
9 114a2991 force adjustment the force, as measured on the closing edge of the door, should not exceed 400n (40kg). If the closing force is measured to more than 400n, a safety infrared reversing sensor must be installed see “install the safety infrared reversing sensor” on page 11. The force setting...
10 114a2991 install the door control locate door control where the garage door is visible, away from door and door hardware and out of the reach of children. Mount at least 1.5m (5 feet) above the floor. Serious personal injury from a moving garage door may result from misuse of opener. Do not allow...
11 114a2991 install the safety infrared reversing sensor (see accessories) install this accessory for all installations on doors over 2.5m in height and when the closing force as measured on the bottom of the door is over 400n (40kg). After opener has been installed and adjusted, the safety infrared...
12 care of your opener when properly installed, opener will provide high performance with a minimum of maintenance. The opener does not require additional lubrication. Lubricate springs and have your door serviced by a professional service technician to maintain good operating condition. Limit and f...
13 10. Door opens but won't close: • check the safety infrared reversing sensor (if you have installed this accessory). If the light is blinking, correct alignment. • if opener light does not blink and it is a new installation, repeat setting the limit and force on pages 7 and 8. Repeat the safety r...
14 114a2991 special features a. Door within a door connection (if this feature is not installed, the jumper must remain intact.) if installed, the door must be closed during door within a door operation, and wiring must be correct. Remove jumper from terminal leads. Replace with contact switch leads...
15 accessories (1) model 62266 1 channel remote (2) model 62171 2 channel remote (3) model 62170 3 channel remote (4) model 62162 3 channel keyring remote (5) model 62173 wireless keyless entry keypad (6) model 62130 multi-function door control panel (7) model 62228 push button wall unit (8) model t...
16 notice 41a2828 178b34 12c778 4a1008 83a11 12vdc pb cd hg 41a5800 183d177 183d178 7423cr3 (chain) 31d525 41a5801-1 (1.7m) 41a5801 (2.3m) 41a5801-2 (2.5m) 41a5801-3 (3.0m) 41b4494-1 7025cr3 (chain) 41b4101-1 210c42 144c77 41a4335e (433mhz) 10a19 41a92 12c855 41a3475-24 178b35 171a28 12c810 29b137 1...
17 37d117-2 171a543 158a49 28a95 41b5348 108d56 171a320 41a5696-4c 41d163 41d605 171a545 171a384-8 171a384 171a315 41b5351-5 41c5392 41b4375-3 171a498 31d525 216a206 41c5350-8 171a479 26b72 41c67 (belt drive) replacement parts 114a2991.
18 specifications input voltage ..............230-240v, 50hz max. Pull force ..........800n power .........................165w normal torque ...........8nm stand-by power rating @ 230v ............6w motor type ...........................Dc permanent lubrication volts ...........................24 ...
114a2991 ©2005, all rights reserved printed in mexico warranty controll-a-door ® automatic garage door opener 1. Definitions ‘b&d’ means (a) in australia - b&d doors of 17 oasis court clontarf, queensland 4019 (b) in new zealand - b&d doors (nz) ltd of 70 allens road east tamaki auckland, which is a...
