- DL manuals
- babymoov
- Baby Monitor
- A014201
- Instruction Manual
Babymoov A014201 Instruction Manual
Summary of A014201
Page 1
Bc-63_manual_05.Pdf 1 22/7/14 6:10 pm.
Page 2
2 thank you for purchasing our a014201 digital green baby monitor. Your unit has been manufactured and checked under the strictest possible quality control to ensure that each monitor leaves the factory in perfect condition. In the unlikely event you find any defects or have any problem, please cont...
Page 3
3 digital technology and aprs this baby monitor employs full digital technology with zero interference. The unit can automatically select free channel or hop to free channel during communication to avoid interference from other electronic devices. In addition, thanks to the automatic power reduction...
Page 4
4 2. Operation using ac adapter the unit can be operated on ac mains using the supplied 5v ac adapter. Connect the output plug of adapter to usb port 16 , make sure the polari - ty is correct. The power supply from the battery will be cut off once the adapter’s output plug is inserted into usb port ...
Page 5
2. Charging up the lithium rechargeable battery connect the output plug of supplied 5v ac adapter to usb port 37 of the charger stand, make sure the polarity is correct. The unit can either be in switch on or off condition, place it into the charger stand. The charging indicator 36 should light up w...
Page 6
6 pairing this process is to match the parent unit with baby unit so that they can communicate with each other while no other devices (even baby monitor of identical model) can interfere with you or receiving your signal. The baby and parent unit are already paired when they are shipped from factory...
Page 7
7 5. Now short press again the power on/off button 1 of one bu. If pairing is successful,the on both pu and bu should change steady green while two beep sound is heard in pu with the corresponding bu number icon 33 or 34 being shown up. 6.Shortpress button 1 oftheremainingbu,twobeepsoundisheardinpuw...
Page 8
8 1. Power on/off button 2. Down touch key 3. Up touch key 4. Menu touch key 5. Night light touch key 6. Night light 7. Microphone 8. Temperature sensor 9. Room temperature indicator 10. Power on/battery low icon 11. Transmit icon 12. Microphone continuous on icon 13. Night light status icon 14. Spe...
Page 9
9 operation baby unit 1. Long press the power on/off button 1 for 3 sec to switch on the unit. The power on icon 10 as well as the assigned baby unit no. 15 should light up steady green while the room temperature indicator 9 starts showing the baby’s room temperature. To turn off, long press the but...
Page 10
10 parent unit 1. Long press the power on/off button 18 for 3 sec to switch on the unit. The power on icon 27 should light up steady green while the temperature indicator 26 will show the baby’s room temperature within 10 sec. To turn off, long press the button 18 again. 2. Setting of out of range a...
Page 11
11 short touch icons 19 or 20 to make your selection, then short press button 18 to confirm. Means out of range alarm function is enabled while means this function is disabled. When set to , the level of radiation from bu is reduced, however, the pu will not provide an alarm when it falls outside th...
Page 12
12 c. Short touch icons 19 or 20 , set the lower temperature limit below which the unit will provide an alarm. The allowed selectable temperature range is -9 to +44 ℃ ℃ or 2 lower than the selected upper limit. In case is selected, no lower ℃ temperature limit is set. Confirm your setting by short p...
Page 13
13 7. If the unit is paired to work with two bu, bu no.1 always has priority. This means while the unit is listening to signal from bu no. 2, in case bu no. 1 starts transmitting, the unit will immediately switch listening to bu no.1 until it stops to transmit, then the unit will switch back listen ...
Page 14
14 11. Whenever the baby’s room temperature falls outside the range as preset by the upper and lower temperature limits, an alarm will be heard. Depending on whether the upper or lower limit is exceeded, the corresponding icon 31 or 32 will light up and the current temperature reading start flashing...
Page 15
15 precautions -use only the supplied ac adapters, use of other adapters may cause damage to the a014201 baby monitor. -when not using the monitor for a long period of time, remove all batteries from the pu, bu to avoid damage due to battery leakage. -disconnect the ac adapter from the wall outlet w...
Page 16
16 problem possible causes solution bu has no - bu is switched off - switch on bu transmission - mic sensitivity is too low - adjust mic sensitivity higher - bu battery has run down or ac - replace with new battery or adapter improperly connected check connection always transmitting - mic sensitivit...
Page 17
17 all european countries except austria, georgia, greece, norway, russian, federation, spain, sweden, the netheriands, ukaine. Bc-63_manual_05.Pdf 16 22/7/14 6:10 pm.
Page 18
1 8.
Page 19
Fcc caution: the user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to...