1. DL manuals
  2. Balt
  3. Indoor Furnishing
  4. ROLZ-2
  5. Assembly Instructions Manual

Balt ROLZ-2 Assembly Instructions Manual

Manual is about: Portable AV/Conference Center

Summary of ROLZ-2

  • Page 1

    1 1234567890123456789012345678901212345678901234567890123456789012123456789012 1234567890123456789012345678901212345678901234567890123456789012123456789012 1234567890123456789012345678901212345678901234567890123456789012123456789012 1234567890123456789012345678901212345678901234567890123456789012123...

  • Page 2: Rolz-2

    2 p-1 left side panel 1 ea p-2 right side panel 1 ea p-3 back panel 1 ea p-4 keyboard shelf 1 ea p-5 fixed shelf 1 ea p-6 removable shelf 1 ea p-7 top platform 1 ea p-8 handle 1 ea p-9 bottom panel 1 ea a 1 ½” flat head screw 2 ea a1 2 ½” flat head screw 2 ea a2 long wood screw 8 ea a3 short wood sc...

  • Page 3: Rolz-2

    3 p-10 door- left 1 ea p-11 door - right 1 ea p-12 threaded axle 1 ea p-13 drawer back 1 ea p-14 drawer front 1 ea p-15 drawer side 2 ea p-16 drawer bottom 1 ea p-17 slide spacer 4 ea part drawing description qty part drawing description qty hardware list p washer 16mm 6 ea r glide 2 ea s washer 30m...

  • Page 4

    4 install 1 slide spacers (p-17) and 1 drawer slide (e) to left side panel (p-1) and secure using 2 wood screws (a2) [packaged with slides] as shown in illustration # 1. (see detail on page 3) illustration # 1 repeat steps1 through 4 for the right side panel (p-2). L l b e a2 1. 2. 3. To assemble: i...

  • Page 5

    5 place the back panel (p-3) with the holes facing up and install 6 each cam locks (k) into the large holes (pre-installed) as shown in illustration # 2. Illustration # 2 place the top platform (p-7)and the fixed shelf (p-5) with the pre- drilled holes facing up and install 4 cam locks (k) into the ...

  • Page 6

    6 to secure cam locks, insert large phillips head screwdriver and turn cam lock 1/4 turn (90 degrees) clockwise. 10. 9. Illustration # 5 p-1 p-2 p-3 p-5 p9 p-7 attach side panels (p-1 & p-2) to the back panel (p-3) , the top platform (p-7) the fixed shelf (p-5), and the bottom panel (p-9) as shown i...

  • Page 7

    7 illustration # 6 11. Illustration # 7a a3 a3 p-4 attach handle (p-8) to the side panels (p-1 & p-2) using 2 each screws (a) as shown in illustration # 6. Tighten screws (a) using small allen wrench (n1). Secure the cam locks located at the top of the back panel and in the top shelf by turning cam ...

  • Page 8

    8 illustration # 9 illustration # 8 attach left door (p-10) to the left side panel (p-1) using 2 each door hinges (m) and 12 each short wood screws (a3) as shown in illustration #8. P-10 m p-1 a3 a4 t z1 y attach door handle (y) to left door (p-10) using 2 screw (z1). Attach right door (p-11) to the...

  • Page 9: 1-800-749-2258

    9 do not use unless all screws are tight. At least every six months, check all screws to be sure they are tight. If parts are missing, broken, damaged, or worn, stop use of the product until repairs are made by your dealer using factory authorised parts. Place the 2 drawer sides (p-15) with the hole...

  • Page 10

    10 illustration # 13 illustration # 14 illustration # 15b attach the drawer front (p-14) to the drawer sides (p-15) and secure by turning the cam locks (l) 1/4 turn until they lock. As shown in illustration # 13. Attach drawer knob (x) to drawer front (p-14) using 1 screw (z). P-14 x z p-15 attach t...

  • Page 11

    11 rolz - 04/28/04 12 ¼ 22 4 ½ 9 ¼ 15¾ 21¼ 44 19-¾ x 15 16 ¼ 39 ½ shipping information 4.2 cubic feet 92 lbs . 50” 24” 6” rolz-2 portable av/conference center for more information 1-800-749-2258.