Bullet DVR Multi- Cam V2.0 User Manual - page 18
Configuration via AV-OUT
:
It is also possible to change the configuration of the Bullet DVR unit, using the wireless remote control while
connected to an external TV or monitor. This allows you to preview your camera’s position and screen layout
live, without having to record a short clip and play it back on your PC.
Start by connecting the supplied cable to the A/V jack on the DVR, and the remaining 2x RCA plugs into any
available A/V input from your TV. The yellow plug is for video, and the white plug is for audio. Your TV will need
to be set to LINE IN mode in order to view the feed from the DVR unit. Note that the DVR cannot power your TV
or monitor, which needs to be powered on separately.
Point the wireless remote at the IR receiver, and press the Menu key
once. All the available configuration
parameters will appear on the TV screen, which are:
o Video
o Audio
o Record
o OSD
o System
o 3 CH
o Beacon
You can easily navigate and configure each of these sub-
menus, using the wireless remote controller’s arrow keys
and pressing the OK key to select any parameter. If you
enter the menu and no key is pressed within 8 seconds,
you will exit the menu automatically and will need to press
the menu key again to re-enter it. Pressing the left arrow
key within the menu will take you back one step.
When a Bullet Camera is connected to any one of the
three CAM inputs while the A/V cable is hooked up to your
TV or monitor, you will be able to view a live image from the
selected camera input.
You can quickly change the selected CAM input by pressing
the PIP key on the remote, followed by any of the
numbered keys from 1 to 3. For example, pressing the
PIP key followed by the #2 key would make the full screen
image from CAM2 appear on your monitor. This let you
easily jump from one camera to the other, and adjust
the image as you require. Then you can go into the 3 CH
configuration menu and setup the Picture-in-Picture
combination you desire.
Note that when configuring the unit via the AV-OUT, you
do not have access to all the parameters found within the
PC configuration software. There are more parameters
available when you configure the unit using the software,
but the most used ones are available via the AV-OUT menu.
Below is the actual AV-OUT configuration menu structure:
user`s manual
user`s manual
user`s manual
Product appearance and specifications are subject to change without notice
18
MENU
OK
Menu
Menu item
Parameter
Video
Standard
• NTSC
• NTSC-433
• PAL
• SECAM
Audio
Source
• Line in
• Ext Mic
• Int Mic
Gain
• Lowest
• Lower
• Low
• Medium
• High
Record
Format
• Mpeg-2
• Mpeg-4
Quality
• LQ
• EP
• LP
• SP
• HQ
Auto Rec
• Disable
• Enable
Profile
• Load profile
OSD
Stamp
• Disable
• Enable
System
Date
• 00-00-00
Time
• 00:00:00
Beep
• Disable
• Enable
CAM Volt
• 5V to 12V
Power Off
• Disable
• 5 Mins
• 10 Mins
• 15 Mins
Connect
• Direct
• LAN
3 CH
Layout
• CH_1
• CH_2
• CH_3
• PIP
• PIP-2
• PIP-2-B
• H-SPLIT
• V-SPLIT
• PIP-3
• PIP-3-B
Border
• Enable
• Disable
Blink
• Enable
• Disable
Color
• Black
• Low grey
• High grey
• White
Size
• 1/9
• 1/6
• 1/4
Position
• 1 to 9
PadColor
• Black
• Low grey
• High grey
• Blue
Beacon
Laptimer
• Enable
• Disable
Mask Time
0 to 99 secs
As Split
• Yes
• No
Splits
• 0 to 4
Sysclock
• True up