1. DL manuals
  2. Bunn
  3. Ice Maker
  4. ULTRA-2 PAF
  5. Installation & Operating Manual

Bunn ULTRA-2 PAF Installation & Operating Manual

Manual is about: Bunn Food Warmer User Manual

Summary of ULTRA-2 PAF

  • Page 1

    Ultra-1 ultra-2 installation & operating guide bunn-o-matic corporation post office box 3227 springfield, illinois 62708-3227 phone: (217) 529-6601 fax: (217) 529-6644 to ensure you have the latest revision of the operating manual, or to view the illustrated parts catalog, programming manual, or ser...

  • Page 2

    2 40563 041108 bunn-o-matic commercial product warranty bunn-o-matic corp. (“bunn”) warrants equipment manufactured by it as follows: 1) all equipment other than as specified below: 2 years parts and 1 year labor. 2) electronic circuit and/or control boards: parts and labor for 3 years. 3) compresso...

  • Page 3

    3 introduction this equipment dispenses granita-type and cold liquid drinks on demand from separate hoppers. Operating controls are accessible only through password protection. Contents introduction & warranty .............................................................................................

  • Page 4

    4 initial setup caution – the dispenser is very heavy! Use care when lifting or moving it. Use at least two people to lift or move the dispenser. 3. Remove the rear plastic plug from the trim strip between the hopper drip trays and loosen the auger motor cover screws. 2. Remove all shipping material...

  • Page 5

    5 11. Thoroughly rinse the hoppers and install them over the augers and cooling drums. 15. Set the lid(s) on the hopper(s). Lift slightly and slide back or front for filling. 16. Plug in the hopper lid lamp cord(s). 17. Assemble the drip tray. Initial setup (cont.) 12. Slide the hopper(s) into place...

  • Page 6

    6 p3678 set consistency this function allows the operator to adjust the ice consistency, or torque of each auger when answered yes (“ice”). Two screens will appear for left and right. The operator can scroll through a range of a minimum of 1 (ultra) to a maximum of 16 (ice). Factory default is 10. S...

  • Page 7

    7 set time and date selecting yes (ice) allows the operator to set the date (yy mm dd) and time (hr min sec) for display on the home screen. Set date time ? No y e s year 2005 (-) next (+) month 1 (-) next (+) month day 25 (-) next (+) hour 10 am (-) next (+) minute 45 (-) next (+) second 30 (-) nex...

  • Page 8

    8 operating controls ultra-1 there are three of these switches that will be used for the operation of the dispenser. 1. Switch (upper left corner of the control pad) this switch is the on/off toggle switch which powers up the dispenser and the lcd display. When on the date and time toggle back and f...

  • Page 9

    9 operating controls ultra-2 there are five of these switches that will be used for the operation of the dispenser. 1. Switch (upper left corner of the control pad) this switch is the on/off toggle switch which powers up the dispenser and the lcd display. When on the date and time toggle back and fo...

  • Page 10

    10 using the dispenser for granita-type products 1. Lift the lid slightly for the selected hopper and slide back to gain access to the hopper. 2. Place the pre-mixed liquid product in the selected hopper. 3. A. Press and release the (on/off) switch to power on the dispenser. B. Press and release the...

  • Page 11

    11 other recommendations for your dispenser • whether liquid concentrate or granulated powder, all product must be thoroughly mixed before adding it to the hoppers. • for best results with granita-type products, use only products with an apparent brix of 12 or higher. Some products may work with an ...

  • Page 12

    12 10. Place all parts in a clean sink with mild hot water (120°f) and sanitizer solution. Allow all parts to soak for at least 5 minutes. Carefully wash all components with a clean wash cloth in the hot water and sanitizer solu- tion. Use a clean, soft bristle brush as needed for the smaller compon...

  • Page 13

    13 1. Install the seal(s) over the flange at the rear of the cooling drum(s) and press the seal(s) firmly into place as shown. 2. Align the auger shaft(s) with the auger(s). Push the auger(s) as far as they will go and rotate so the flat face of the auger shaft is aligned with the flat face of the a...

  • Page 14

    14 user notices carefully read and follow all notices on the equipment and in this manual. They were written for your protec- tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 27442.0000 32162.0000 (ultra-2) 00986.0002 charge type r404a, amount 9.5 oz (269...