1. DL manuals
  2. Cabletron Systems
  3. Switch
  4. Netlink FRX4000
  5. Reference Manual

Cabletron Systems Netlink FRX4000 Reference Manual

Manual is about: Frame Relay Access Products

Summary of Netlink FRX4000

  • Page 1

    Mib reference guide for cabletron frame relay products document number 09-41-06-149-03 the com plete network ing solution tm.

  • Page 3

    Mi b ref erence g uide iii rev date reason for update 01 august 1997 initial version 02 september 1997 frame relay module 03 march 1998 release 4.0 cabletron systems reserves the right to make changes in specifications and other infor- mation contained in this document without prior notice. The read...

  • Page 4

    Iv cabletron frame relay products this manual describes the various mibs supported in cabletron’s frame relay access product family (smartswitch 1800, frx, and 9w004). Most of the information is taken from the mib documents or cabletron user documentation. These appropriate product-specific user gui...

  • Page 5

    Mi b ref erence g uide v table of contents introduction .............................................................................................. 1 netlink mib .............................................................................................. 3 network group (netlink.6) ...............

  • Page 6

    Vi netlink frame relay products ipxconfiginterface (ipxconfig.2) ......................................... 77 ipxconfignodedefault (ipxconfig.3) .................................. 85 nlifipinterfaces (nlinterfaces.4).................................................. 86 nlifiptable (nlifipiinterfaces...

  • Page 7

    Mi b ref erence g uide vii sdlclsadmintable (sdlclsgroup.1)....................................... 177 sdlclsopertable (sdlclsgroup.2)........................................... 183 sdlclsstatstable (sdlclsgroup.3)........................................... 190 novell ipx mib ..........................

  • Page 8

    Viii netlink frame relay products.

  • Page 9: Introduction

    Introduction the snmp agent in cabletron’s frame relay access product line supports snmp mibs (message information bases) according to the following tables. Note that the columns list the earliest releases that support each group/table. (these and all subsequent releases of a product support the gro...

  • Page 10

    2 cabletron relay access products 1 some variables are read-only. See individual descriptions later in this document. Note that in the case of the portbscigroup and portsdlcgroup, all variables are read-write except those in the "oper" tables, which have read-write equivalents in the "admin" tables....

  • Page 11: Netlink Mib

    Mi b ref erence 3 netlink mib inaccessible variables are not included. Network group (netlink.6) this group is supported only on the netlink frx8000 (as described on page 1), as well as nucleus 7000 (supported for ease of transition to frx8000). Nsmaxneigh syntax: integer access: read only status: m...

  • Page 12

    4 cabletron relay access products nsstatus syntax: integer access: read only status: mandatory description:operational status of the node: bit 0 on = value 1 = node is defined in database. Bits 0 & 7 on = value 9 = node is operational. ::= { network.1.3.1.2} nsnumneigh syntax: integer access: read o...

  • Page 13

    Mi b ref erence 5 node group (netlink.7.1) nodemodel syntax: integer ( 2,3,5,6,7,8 ) access: read only status: mandatory description:identification of hardware platform for graphics-based network manager: 2 = frx6000/frx8000 model 2, 3 = frx6000/frx8000 rackmount chassis or frame relay module (frm),...

  • Page 14

    6 cabletron relay access products description:state of this entry. ("disable" means "do not send.") ::= { node.3.3.1.3} tpadrslev syntax: integer ( 1–4 ) access: read/write status: mandatory description:lowest severity level traps that will be sent: 1 = critical(highest), 2 = major, 3 = minor, 4 = i...

  • Page 15

    Mi b ref erence 7 rlpmemorysize syntax: integer ( 4 or 8 ) access: read only status: mandatory description:amount of memory installed on this rlp. ::= { rlpconfigtable.1.3} rlplic1type syntax: integer ( 1–5, 8, 10, 11 ) access: read/write status: mandatory description:type of line interface card (li...

  • Page 16

    8 cabletron relay access products frx8000), 0e = llc2-r (frx4000 and smartswitch 1800 only), 10 = netview service point. ::= { rlpconfigtable.1.6} rlpgroupnumber (frx7000 only) syntax: integer ( 1–4 ) access: read only status: mandatory description:group to which this rlp belongs. Up to six rlps can...

  • Page 17

    Mi b ref erence 9 port group (netlink.7.3) portx25group (port.1) portphyx25admintable (portx25group.1) this table contains netlink enterprise-specific objects to manage a physical x.25 port. Changing one of these parameters may take effect on the operating port immediately or may wait until the inte...

  • Page 18

    10 cabletron relay access products 1.288m 1.344m 1.4m 1.408m 1.456m 1.472m 1.512m 1.536m 1.568m 1.6m 1.624m 1.664m 1.668m 1.728m 1.792m 1.856m 1.92m 1.984m 2.048m if an rs-232 dce port is directly connected to the dte via the standard cabletron cable, the maximum supported speed is 64k. If longer ca...

  • Page 19

    Mi b ref erence 11 portphyx25admininactivitytimer syntax: integer ( 1–30 ) access: read/write status: mandatory description:period (in minutes) of inactivity allowed between calls. Once the timer expires, the port is disabled until the next call is placed, if a dial-out port, or the disconnect timer...

  • Page 20

    12 cabletron relay access products status: mandatory description:string of 8 bytes, with each byte indicating 8 ports on an rlp that may be a part of a trunk group. Since the smartswitch 1800 and frx4000 do not have multiple rlps, only the first byte is valid for these devices. Each port is represen...

  • Page 21

    Mi b ref erence 13 pdu, then a generr response is returned. ::= { portphyx25admintable.1.11 } portphyx25opertable (portx25group.2) this table contains read-only variables that reflect the actual operating parameter values. Unless a value was changed in the portphyx25admintable after the interface be...

  • Page 22

    14 cabletron relay access products portlogicalx25admincxnpriority syntax: integer ( 0–9 ) access: read/write status: mandatory description:priority of the connection among others on the physical port. ::= { portlogicalx25admintable.1.2 } portlogicalx25adminrfc1490 syntax: integer {annexg ( 1 ), rfc1...

  • Page 23

    Mi b ref erence 15 use by the managed device, and which is supplied by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a generr response is returned when the row does not exist. Createandgo , which is supplied by a m...

  • Page 24

    16 cabletron relay access products configured values if a configured parameter was configured after the interface was started. Portx25adminblockedflag syntax: integer { no ( 1 ), yes ( 2 ) } access: read/write status: mandatory description:flag which when set, means the port will not be enabled afte...

  • Page 25

    Mi b ref erence 17 call packet if not already included. ::= { portx25admintable.1.4 } portx25adminrevchgaccpt syntax: integer { no ( 1 ), yes ( 2 ) } access: read/write status: mandatory description:flag that, if set, that authorizes transmission of incoming calls that request the reverse charge fac...

  • Page 26

    18 cabletron relay access products description:maximum data packet size that will be allowed to pass through this port. ::= { portx25admintable.1.9 } portx25admindefpktsize syntax: integer ( 16..4096 ) access: read/write status: mandatory description:packet size that will be assigned to an incoming ...

  • Page 27

    Mi b ref erence 19 valid values are listed below. Line speeds are in bits per second: class line speed class line speed 3 75 9 4800 4 150 10 9600 5 300 11 19.2k 6 600 12 48k 7 1200 13 64k 8 2400 ::= { portx25admintable.1.13 } portx25admincugpref syntax: integer { no ( 1 ), yes ( 2 ) } access: read/w...

  • Page 28

    20 cabletron relay access products allowed to make calls outside its cugs. ::= { portx25admintable.1.17 } portx25opertable this table contains read only variables that reflect the actual operating parameter values. Unless a value was changed in the portx25admintable after the interface became operat...

  • Page 29

    Mi b ref erence 21 portfrportindex syntax: integer ( 1–64 , where 1–8 correspond to physical port numbers 0–7 and 9–64 correspond to logical port numbers 8–63 .) access: read only status: mandatory description:port number of the frame relay port. ::= { portfrconfigtable.1.2} portfrblockedflag syntax...

  • Page 30

    22 cabletron relay access products parameters (cir, b c , b e ). ::= { portfrconfigtable.1.6} portfrbandwidthallocation syntax: integer {no ( 1 ), yes ( 2 )} access: read/write status: mandatory description:enables (if yes ) enforcement of bandwidth allocation on the frame relay port if the availabl...

  • Page 31

    Mi b ref erence 23 portfrrcvclkfrmdte syntax: integer {no ( 1 ), yes ( 2 )} access: read/write status: mandatory description:allows the clock to be looped back from the dte using the tt (terminal timing) signal. This is valid only if the port is physical dce (determined by the attached i/o cable) an...

  • Page 32

    24 cabletron relay access products note that all of the above values may be specified in a man- agement protocol set operation, and only the active value will be returned in response to a management protocol retrieval operation. For a management protocol set opera- tion, if other variable bindings a...

  • Page 33

    Mi b ref erence 25 portfrbackupuseonly syntax: integer {no (1), yes (2)} access: read/write status: mandatory description:determines whether all dlcis on the port will be reserved exclusively as backups for other dlcis in the same node. If yes is specified for this object, the port will remain dis- ...

  • Page 34

    26 cabletron relay access products portdlciincomingcir syntax: integer ( 0–2000 ) (kbps) access: read/write status: mandatory description:committed information rate (cir) supported for incoming data on the dlci. ::= { portdlciconfigtable.1.4} portdlcioutgoingcir syntax: integer ( 0–2000 ) (kbps) acc...

  • Page 35

    Mi b ref erence 27 description:incoming excess burst size (b e ), the maximum amount of incoming data above the committed burst size (b c ) that the network will try to transfer on the dlci during the interval determined by b c /cir. ::= { portdlciconfigtable.1.8} portdlcioutgoingbe syntax: integer ...

  • Page 36

    28 cabletron relay access products description:used to manage the creation and deletion of conceptual rows in the portdlciconfigtable , and follows the snmpv2 rowstatus conventions by supporting the following values: active , which means the conceptual row is available for use by the managed device,...

  • Page 37

    Mi b ref erence 29 a dlci cannot be both a backup and a primary. Also, on an frx6000 or frm, the primary and all backups must be on the same rlp, or a pvc must be configured between the dlcis. Do not configure a backup group number on this dlci at the remote (non- initiating) end. ::= { portdlciconf...

  • Page 38

    30 cabletron relay access products portfrbackupport syntax: integer ( 1–8 , which correspond to physical port numbers 0–7 ) access: read only status: mandatory description:physical port on which the backup dlci is being configured. ::= { portfrbackupgrouptable.1.2 } portfrbackupdlci syntax: integer ...

  • Page 39

    Mi b ref erence 31 6000, smartswitch 1800, or frm with the backup protocol enabled on the remote dlci connected to this backup group entry. The remote node must be the same one to which the primary dlci was connected, and (frx6000/frm only) the remote node’s backup dlci must be on the same rlp as it...

  • Page 40

    32 cabletron relay access products pdu, then a generr response is returned. ::= { portfrbackupgrouptable.1.7 } portbscigroup (port.4) portbsciadmintable (portbscigroup.1) portbsciadminblockedflag syntax: integer { 1 (disabled), 2 (enabled)} access: read/write status: mandatory description:causes the...

  • Page 41

    Mi b ref erence 33 1.152m 1.176m 1.216m 1.232m 1.28m 1.288m 1.344m 1.4m 1.408m 1.456m 1.472m 1.512m 1.536m 1.568m 1.6m 1.624m 1.664m 1.668m 1.728m 1.792m 1.856m 1.92m 1.984m 2.048m if an rs-232 dce port is directly connected to the dte via the standard cabletron cable, the maximum supported speed is...

  • Page 42

    34 cabletron relay access products portbsciadmingenerateclock syntax: integer {no ( 1 ), yes ( 2 )} access: read/write status: mandatory description:determines whether the port will generate the clock necessary to synchronize traffic over the link. ::= { portbsciadmintable.1.7} portbsciadminrcvclock...

  • Page 43

    Mi b ref erence 35 including call information in a call request packet. ::= { portbsciadmintable.1.11} portbsciadminclearvconlastdevicedown syntax: integer {no ( 1 ), yes ( 2 )} access: read/write status: mandatory description:causes (if yes ) the virtual circuit to be cleared when no terminals are ...

  • Page 44

    36 cabletron relay access products portbsciadminmultidrop syntax: integer {no ( 1 ), yes ( 2 )} access: read/write status: mandatory description:specifies whether transmission will be multidrop. ::= { portbsciadmintable.1.16} portbsciadminslowpollretrycount syntax: integer ( 10–150 ) access: read/wr...

  • Page 45

    Mi b ref erence 37 portbsciadminpollinterval syntax: integer ( 100–1000 ) (milliseconds) access: read/write status: mandatory description:interval between passes through the polling list. ::= { portbsciadmintable.1.21} portbsciadminnoresponsetimer syntax: integer ( 2–10 ) (seconds) access: read/writ...

  • Page 46

    38 cabletron relay access products description:number of times the netlink device will send a frame when the receiving device is unable to acknowledge. ::= { portbsciadmintable.1.25} portbsciadminblockcheck syntax: integer {crc16 ( 1 ), even-lrc ( 2 ), odd-lrc ( 3 )} access: read/write status: manda...

  • Page 47

    Mi b ref erence 39 row already exists. Destroy , which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a man- agement protocol set operation, and only the active value will be...

  • Page 48

    40 cabletron relay access products portbsciopertable (portbscigroup.2) this table contains read-only variables that reflect the actual operating parameter values. Unless a value was changed in the portbsciadmintable after the interface became operational, the values in the portbsciopertable should m...

  • Page 49

    Mi b ref erence 41 bscisubscradmintable (portbscigroup.3) bscisubscradminsequence syntax: integer ( 1–16 ) access: read only status: mandatory description:subscriber index for a specific bsci port subscriber. ::= { bscisubscradmintable.1.1} bscisubscradminlocalid syntax: nlsubscriberaddress access: ...

  • Page 50

    42 cabletron relay access products bscisubscradminautocallmaxrtry syntax: integer ( 0–255 ) access: read/write status: mandatory description:maximum number of times an autocall will be sent. ::= { bscisubscradmintable.1.6} bscisubscradminconnectionid syntax: integer ( 0–255 ) access: read/write stat...

  • Page 51

    Mi b ref erence 43 will be returned in response to a management protocol retrieval operation. For a management protocol set opera- tion, if other variable bindings are included in the same pdu, then a generr response is returned. ::= { bscisubscradmintable.1.8 } bscisubscropertable (portbscigroup.4)...

  • Page 52

    44 cabletron relay access products identifier that must match a connection id on a bsc interactive port. (see bscisubscradminconnectionid .) ::= { bscidevadmintable.1.3} bscidevadminsingleuservc syntax: integer {no ( 1 ), yes ( 2 )} access: read/write status: mandatory description:specifies whether ...

  • Page 53

    Mi b ref erence 45 response is returned when the row does not exist. Createandgo , which is supplied by a management station wishing to create a new instance of a con- ceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management ...

  • Page 54

    46 cabletron relay access products bscidevopertable (portbscigroup.6) this table contains read only variables that reflect the actual operating parameter values. Unless a value was changed in the bscidevadmintable after the interface became operational, the values in the bscidevopertable should matc...

  • Page 55

    Mi b ref erence 47 description:sna pad type. ::= { portsdlcadmintable.1.4} portsdlcadmingenerateclock syntax: integer {no ( 1 ), yes ( 2 )} access: read/write status: mandatory description:determines whether the port will generate the clock necessary to synchronize traffic over the link. ::= { ports...

  • Page 56

    48 cabletron relay access products sent when the remote pad clears the connection. ::= { portsdlcadmintable.1.9} portsdlcadminlpdasupport syntax: integer {none ( 1 ), lpda-1 ( 2 ), lpda-2 ( 3 )} access: read/write status: mandatory description:lpda support on the sdlc port. ::= { portsdlcadmintable....

  • Page 57

    Mi b ref erence 49 if an rs-232 dce port is directly connected to the dte via the standard cabletron cable, the maximum supported speed is 64k. If longer cabling is used, the maximum speed is 19.2k. (the eia standard for rs-232 addresses speeds up to 19.2 kbps.) t1, e1 port speeds cannot be set here...

  • Page 58

    50 cabletron relay access products pdu, then a generr response is returned. ::= { portsdlcadmintable.1.13 } portsdlcadminidlefillchar syntax: integer {hex-ff ( 1 ), hex-7e ( 2 )} access: read/write status: mandatory description:specifies a character that will be inserted into the stream when thesna ...

  • Page 59

    Mi b ref erence 51 portsdlcoperdisablerequestdisconnect (portsdlcopertable.1.9) portsdlcoperlpdasupport (portsdlcopertable.1.10) portsdlcoperconnector (portsdlcopertable.1.11) portsdlcoperspeed (portsdlcopertable.1.12) portsdlcadminidlefillchar (portsdlcopertable.1.13) portsdlcadmininactivitytimer (...

  • Page 60

    52 cabletron relay access products lssdlcadminretrytime syntax: integer ( 15–225 ) (seconds) access: read/write status: mandatory description:time interval between retransmissions of a connection request. This is used only when lssdlcadminautocall is en- abled. ::= { lssdlcadmintable.1.4} lssdlcadmi...

  • Page 61

    Mi b ref erence 53 values: active , which means the conceptual row is available for use by the managed device, and which is supplied by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a generr response is returned wh...

  • Page 62

    54 cabletron relay access products lssdlcopertable (portsdlcgroup.4) this table contains read only variables that reflect the actual operating parameter values. Unless a value was changed in the lssdlcadmintable after the interface became operational, the values in the lssdlcopertable should match t...

  • Page 63

    Mi b ref erence 55 description:this is used in conjunction with idnum (see next entry) in generating the node field in an xid frame (format 0 or 3) to establish a link station connection to the host. ::= { lssdlcllc2admintable.1.3} lssdlcllc2adminidnum syntax: integer ( 0–1048575 ) access: read/writ...

  • Page 64

    56 cabletron relay access products lssdlcllc2adminlant1 syntax: integer ( 100–25000 ) (milliseconds) access: read/write status: mandatory description:llc2 reply timer ( t1 ), used to detect the failure to receive a required acknowledgment or response from the remote link station. The link station wi...

  • Page 65

    Mi b ref erence 57 lssdlcllc2adminlant2 syntax: integer ( 100–5000 ) (milliseconds) access: read/write status: mandatory description:receiver acknowledgment timer ( t2 ), used by the link station to delay sending an acknowledgment of a received information lpdu. The timer is started when the lpdu is...

  • Page 66

    58 cabletron relay access products information lpdus that the link station can have outstanding. ::= { lssdlcllc2admintable.1.10} lssdlcllc2adminbag syntax: integer ( 0–16 ) access: read/write status: mandatory description:bandwidth allocation group. Bandwidth allocation groups can ensure that respo...

  • Page 67

    Mi b ref erence 59 by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a generr response is returned when the row does not exist. Createandgo , which is supplied by a management station wishing to create a new instanc...

  • Page 68

    60 cabletron relay access products lssdlcllc2opertable (portsdlcgroup.6) this table contains read only variables that reflect the actual operating parameter values. Unless a value was changed in the lssdlcllc2admintable after the interface became operational, the values in the lssdlcllc2opertable sh...

  • Page 69

    Mi b ref erence 61 portt1adminframingmode status: integer {fullt1( 1 ), ds0at1( 2 )} access: read-write status: mandatory description:specifies how this t1 port is to function. Ds0at1 specifies a 24-channelized t1. ::= {portt1admintable.1.3} portt1adminframemodelselect status: integer {d4 ( 1 ), esf...

  • Page 70

    62 cabletron relay access products status: mandatory description:used to manage the creation and deletion of conceptual rows in the portt1admintable , and follows the snmpv2 rowstatus conventions by supporting the following values: active , which means the conceptual row is available for use by the ...

  • Page 71

    Mi b ref erence 63 description:determines the level of data encoding: 1 =nrz (non-return to zero), which means that 1 represents high-level encoding and 0 is low-level. 2 =nrzi (non-return to zero inverted), which means that 1 represents no change in level and 0 is a change. ::= { portt1admintable.1...

  • Page 72

    64 cabletron relay access products nliftable (nlinterfaces.1) nlifrlp syntax: integer ( 1–8, 250–252 ) access: read only status: mandatory description:rlp number. 1-8 are physical rlp cards 0–7 . 250 , 251 and 252 define ip, ipx and llc2 interfaces, respectively. ::= { nliftable.1.1} nlifport syntax...

  • Page 73

    Mi b ref erence 65 description:associated index into the mib-ii iftable for this port. ::= { nliftable.1.4} nliftableindex syntax: integer access: read only status: mandatory description:index into a table used to describe additional information for this port. See nliftableoid as the pointer to the ...

  • Page 74

    66 cabletron relay access products 15 = blue alarm, 16 = yellow alarm, 17 = red alarm, 18 = on hook, 19 = off hook, 20 = dialing, 21 = active voice call, 22 = on hook pending. ::= { nliftable.1.8} nlifphyport syntax: integer ( 1–8 ) access: read only status: mandatory description:underlying physical...

  • Page 75

    Mi b ref erence 67 nlifllc2lantype syntax: integer {ethernet ( 1 ), token ring ( 2 ) } access: read/write status: mandatory description:type of lan connected to the llc2 interface. ::{ nlifllc2lantable.1.3 } nlifllc2lancard syntax: integer ( 1–2 , which correspond to actual card numbers 0–1 ) access...

  • Page 76

    68 cabletron relay access products use by the managed device, and which is supplied by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a generr response is returned when the row does not exist. Createandgo , which is...

  • Page 77

    Mi b ref erence 69 after a boot-up of the node. ::= { nlifllc2lantable.1.9 } nlifllc2frtable (nlifllc2interfaces.2) this table defines netlink llc2 frame relay interfaces. Nlifllc2frrlp syntax: integer ( 1–8 ) access: read only status: mandatory description:rlp number on the node. 1–8 correspond to ...

  • Page 78

    70 cabletron relay access products avoid configuring parallel bridge/llc2 frame relay links between two frx/frm/smartswitch devices if one path is in native llc2 format and the other in some other format. Since the same interfaces are used for both protocols and the spanning tree will eliminate dual...

  • Page 79

    Mi b ref erence 71 ( nlifllc2frformat ) is native-llc2. ::= {nlifllc2frtable.1.7} nlifllc2frsessiontype syntax: integer {terminated ( 1 ), originated ( 2 ), not-applicable ( 3 )} access: read/write status: mandatory description:if originated, means that llc2 connects from the confi- gured host mac a...

  • Page 80

    72 cabletron relay access products use by the managed device, and which is supplied by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a generr response is returned when the row does not exist. Createandgo , which is...

  • Page 81

    Mi b ref erence 73 ipxconfig (nlinterfaces.3) ipxcon figrouting (ipxconfig.1) ipxstaticrouteconfigtable (ipxconfigrouting.1) this is a table of ipx static (fixed) routes. Ipxstaticrouteconfigcircindex syntax: integer ( 1–65535 ) access: read only status: mandatory description:unique identifier of th...

  • Page 82

    74 cabletron relay access products active , which means the conceptual row is available for use by the managed device, and which is supplied by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a generr response is ret...

  • Page 83

    Mi b ref erence 75 network. ::= {ipxservconfigtable.2.2} ipxservconfigservnetworkaddress syntax: integer access: read/write status: mandatory description:ipx network number portion of the ipx address of the server identified by ipxservconfigservname . ::= {ipxservconfigtable.2.3} ipxservconfigservno...

  • Page 84

    76 cabletron relay access products ipxservconfiginterface syntax: integer ( 0–65535 ) access: read/write status: mandatory description:ipx network number assigned to the interface used to send packets that are destined for this server. ::= {ipxservconfigtable.2.8} ipxservconfigrowstatus syntax: rows...

  • Page 85

    Mi b ref erence 77 ipxcon figinterface (ipxconfig.2) this is a table of ipx interfaces. Ipxinterfacenumber syntax: integer ( 1–64 ) access: read only status: mandatory description:sequential number to identify the interface. ::= {ipxconfiginterface.6.1.1} ipxinterfaceblockedportflag syntax: integer ...

  • Page 86

    78 cabletron relay access products over the ipx interface. Ethernet = 45–1518 , 802.5 = 48–4096 , frame relay = 31–4096 , x.25 = 31–4096. ::= {ipxconfiginterface.6.1.5} ipxinterfacenetworkaddress syntax: integer access: read/write status: mandatory description:identifies the local interface to the n...

  • Page 87

    Mi b ref erence 79 ipxinterfacenetbioshops syntax: integer ( 0–255 ) access: read/write status: mandatory description:maximum number of hops allowed for routing a novell- -encapsulated netbios frame. ::= {ipxconfiginterface.6.1.10} ipxinterfaceperiodicripenabled syntax: integer { no ( 1 ), yes ( 2 )...

  • Page 88

    80 cabletron relay access products interface. ::= {ipxconfiginterface.6.1.14} ipxinterfaceripenabled syntax: integer { no ( 1 ), yes ( 2 )} access: read/write status: mandatory description:datermines whether this interface will support rip processing. ::= {ipxconfiginterface.6.1.15} ipxinterfaceripa...

  • Page 89

    Mi b ref erence 81 description:used to delete route entries from the router information table. The timer starts/restars each time an entry is created/ updated. If the timer expires, the router will assume that the entry is no longer valid and the entry will be deleted from the table. ::= {ipxconfigi...

  • Page 90

    82 cabletron relay access products ipxinterfacelancardnumber syntax: integer ( 1–2 , which correspond to actual card numbers 0–1 ) access: read/write status: mandatory description:card number installed in a node. The first or only lan card installed is always 0 , and the second is card 1 . ::= {ipxc...

  • Page 91

    Mi b ref erence 83 ipxinterfacesvcretrytimer syntax: integer ( 5–60 ) access: read/write status: mandatory description:the frequency with which calls will be placed to try to establish a connection. Valid only for type x.25. ::= {ipxconfiginterface.6.1.27} ipxinterfacesvcidletimer syntax: integer ( ...

  • Page 92

    84 cabletron relay access products interface. Valid only for frame relay. ::= {ipxconfiginterface.6.1.31} ipxinterfacesourceport syntax: integer ( 0–7 ) access: read/write status: mandatory description:identifies the location of this end of the frame relay ipx interface. Valid only for frame relay. ...

  • Page 93

    Mi b ref erence 85 destroy , which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a man- agement protocol set operation, and only the active value will be returned in respons...

  • Page 94

    86 cabletron relay access products nlifipinterfaces (nlinterfaces.4) nlifiptable (nlifipiinterfaces.1) this table defines ip interfaces over frame relay, x.25, or lan (ethernet, 802.3, 802.5). Nlifipinterface syntax: integer ( 1–257 ) access: read only status: mandatory description:interface number ...

  • Page 95

    Mi b ref erence 87 overall path over the internet) associated with this interface. ::= { nlifiptable.1.4 } nlifipicmpaddroutes syntax: integer { no ( 1 ), yes ( 2 ) } access: read/write status: mandatory description:flag that indicates whether ip may add routes obtained by icmp, whose error and cont...

  • Page 96

    88 cabletron relay access products device processor in the node uses these priorities to help determine the order in which it will process protocols. ::= { nlifiptable.1.8 } nlifipbag syntax: integer ( 1–16 ) access: read/write status: mandatory description:bandwidth allocation group to which this i...

  • Page 97

    Mi b ref erence 89 nlifipbroadcastaddress syntax: ipaddress access: read/write status: mandatory description:ip address that is used to send to all lan hosts on the network. This object is valid only when the interface type is lan-based. ::= { nlifiptable.1.13 } nlifiplancard syntax: integer ( 0–1 )...

  • Page 98

    90 cabletron relay access products the interface type is x.25. ::= { nlifiptable.1.17 } nlifipsvcidletimer syntax: integer ( 0–5 ) access: read/write status: mandatory description:period (in minutes) that an ip connection remains active with no traffic before the connection is cleared. This object i...

  • Page 99

    Mi b ref erence 91 nlifipsourceport syntax: integer ( 1–8 , which correspond to physical ports 0–7 ) access: read/write status: mandatory description:port of the logical interface of this end of the frame relay link. This object is valid only when the interface type is frame relay. ::= { nlifiptable...

  • Page 100

    92 cabletron relay access products is lan-based. ::= { nlifiptable.1.26 } nlifipunnumberedif syntax: integer { no ( 1 ), yes ( 2 ) } access: read/write status: mandatory description:flag that indicates whether this interface is an unnumbered interface (i.E., does not require a specific source ip add...

  • Page 101

    Mi b ref erence 93 tion, if other variable bindings are included in the same pdu, then a generr response is returned. ::= { nlifiptable.1.28 } nlifipsecondaryaddrtable (nlifipiinterfaces.2) this is a table of secondary ip addresses for the ip interface. Up to 15 secondary addresses can be configured...

  • Page 102

    94 cabletron relay access products description:ip address of the end-to-end sender. ::= { nlifipsecondaryaddrtable.1.4 } nlifipsecondaryaddrbroadcastaddress syntax: ipaddress access: read/write status: mandatory description:ip address that is used to send to all lan hosts on the network. ::= { nlifi...

  • Page 103

    Mi b ref erence 95 wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a man- agement protocol set operation, and only the active value will be returned in response to a management protocol retrieval operation. For ...

  • Page 104

    96 cabletron relay access products description:algorithm used to route calls to the subscriber: 1 = round robin – selects ports specified cyclicly in nu- merical order according to the list of redirection ad- dresses. If the selected port is unreachable or congested, the call request will be sent to...

  • Page 105

    Mi b ref erence 97 nllocalsubscriberredirectoo syntax: integer { 1 (no), 2 (yes)} access: read/write status: mandatory description:will (if yes ) redirect calls according to the nllocalsubscriberredirtable if the primary subscriber device is out of order. ::= { nllocalsubscribertable.1.6} nllocalsub...

  • Page 106

    98 cabletron relay access products managed device. For a management protocol set operation, a generr response is returned when the row already exists. Destroy , which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all ...

  • Page 107

    Mi b ref erence 99 nllocalsubscriberrouteport syntax: integer ( 1–8 , which correspond to physical port numbers 0–7 ) access: read/write status: mandatory description:port number that deines the port part of the routing path. ::= { nllocalsubscriberroutetable.1.4} nllocalsubscriberrouterowstatus syn...

  • Page 108

    100 cabletron relay access products nllocalsubscriberredirtable (subscriber.3) this is a table of re-direction addresses. Nllocalsubscriberredirindex syntax: integer ( 1–5 ) access: read only status: mandatory description:redirection entry index for a local subscriber. ::= { nllocalsubscriberredirta...

  • Page 109

    Mi b ref erence 101 row already exists. Destroy , which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a man- agement protocol set operation, and only the active value will b...

  • Page 110

    102 cabletron relay access products nlllc2hostt1replytimer syntax: timeinterval ( 1–250 ) (100-millisecond increments) access: read/write status: mandatory description:llc2 reply timer ( t1 ), used to detect the failure to receive a required acknowledgment or response from the remote link station. T...

  • Page 111

    Mi b ref erence 103 nlllc2hostt2recvacktimer syntax: timeinterval ( 100–5000 ) (milliseconds) access: read/write status: mandatory description:receiver acknowledgment timer ( t2 ), used by the link station to delay sending an acknowledgment of a received information lpdu. The timer is started when t...

  • Page 112

    104 cabletron relay access products received. When the counter reaches 0 an acknowledgment is sent. N3 is reset whenever an information or supervisory acknowledgment lpdu is sent by the local station. ::= { nlllc2hosttable.1.7} nlllc2hosttwnumberoutstanding syntax: integer ( 1–127 ) access: read/wri...

  • Page 113

    Mi b ref erence 105 description:bandwidth allocation group to which the llc2 host belongs. Bandwidth allocation groups can ensure that response time-sensitive traffic gets access to the available frame relay bandwidth. Each logical port and interface that uses a frame relay port can be assigned to a...

  • Page 114

    106 cabletron relay access products 3 = token ring, 4 = ethernet, 5 = all. ::= { nlllc2hosttable.1.14} nlllc2hostrowstatus syntax: rowstatus access: read/write status: mandatory description:used to manage the creation and deletion of conceptual rows in the nlllc2hosttable , and follows the snmpv2 ro...

  • Page 115

    Mi b ref erence 107 the number is always 300 unless the node is an frx7000. ::= { nlllc2hosttable.1.16 } nlllc2hostgroup syntax: integer ( 1–4 ) access: read only status: mandatory description:traffic group associated with llc2 interface. The number is always 1 unless the node is an frx7000. ::= { n...

  • Page 116

    108 cabletron relay access products sdlc device. If configuring an llc2-to-llc2 connection, this id must match the remote subscriber id of the remote node's llc2 host. ::= { nlllc2termconnectiontable.1.3} nlllc2termconnectionremotesubscriberid syntax: nlsubscriberaddress access: read/write status: m...

  • Page 117

    Mi b ref erence 109 an existing conceptual row. Note that all of the above values may be specified in a man- agement protocol set operation, and only the active value will be returned in response to a management protocol retrieval operation. For a management protocol set opera- tion, if other variab...

  • Page 118

    110 cabletron relay access products description:llc2 host connection's local subscriber id. If configuring an llc2-to-sdlc link, this id must match the remote subscriber configured on the sna port for the sdlc device. If configuring an llc2-to-llc2 connec- tion, this id must match the remote subscri...

  • Page 119

    Mi b ref erence 111 that the sdlc device should be polled for an xid.) ::= { nlllc2origconnectiontable.1.7} nlllc2origconnectionmaxdata syntax: integer ( 265, 521, 1033, 1289, 1545, or 2057 ) access: read only status: mandatory description:corresponds to the piu size configured on the host (paramete...

  • Page 120

    112 cabletron relay access products ceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a generr response is returned when the row already exists. Destroy , which is supplied by a management stati...

  • Page 121

    Mi b ref erence 113 access: read only status: mandatory description:port number. ::= { pinstatustable.1.2 } portpinstatus syntax: octet string access: read only status: mandatory description:the status of all pins for this physical port. There is one octet value for each of the pins. Each octet valu...

  • Page 122

    114 cabletron relay access products status: mandatory description:percentage of total available buffers in use at the moment of inquiry. ::= { rlpstatstable.1.3} rlpstatsinframes syntax: counter access: read only status: mandatory description:number of frames received on the rlp. ::= { rlpstatstable...

  • Page 123

    Mi b ref erence 115 portstatstable (statgroup.3) portstatsrlpindex syntax: integer ( 1–8 , which correspond to actual rlp numbers 0–7 ) access: read only status: mandatory description:rlp number. ::= { portstatstable.1.1} portstatsindex syntax: integer ( 1–8 , which correspond to physical port numbe...

  • Page 124

    116 cabletron relay access products portstatsfcserrors syntax: counter access: read only status: mandatory description:number of frame check sequence (fcs) errors on the port. A value consistently greater than 0 indicates line problems. ::= { portstatstable.1.6} portstatslogicalrejects syntax: count...

  • Page 125

    Mi b ref erence 117 statframe (statgroup.4) frstatstable (statframe.1) frstatsrlpindex syntax: integer ( 1–8 , which correspond to actual rlp numbers 0–7 ) access: read only status: mandatory description:rlp number. ::= { frstatstable.1.1} frstatsportindex syntax: integer ( 1–8 , which correspond to...

  • Page 126

    118 cabletron relay access products (forward event congestion notification). ::= { frstatstable.1.5} frstatsrxfecnframes syntax: counter access: read only status: mandatory description:number of frames received on the port with fecn. ::= { frstatstable.1.6} frstatstxbecnframes syntax: counter access...

  • Page 127

    Mi b ref erence 119 frstatstxanxdframes (netlink.7.8.1.4.1.1.11) syntax: counter access: read only status: mandatory description:number of annex-d frames transmitted on the port. ::= { frstatstable.1.11} frstatsrxanxdframes syntax: counter access: read only status: mandatory description:number of an...

  • Page 128

    120 cabletron relay access products x25txportindex syntax: integer ( 1–8 , which correspond to physical port numbers 0–7 ) access: read only status: mandatory description:port number. ::= { x25txstatstable.1.2} x25txsabmframes syntax: counter access: read only status: mandatory description:number of...

  • Page 129

    Mi b ref erence 121 x25txfrmrframes syntax: counter access: read only status: mandatory description:number of frmr (frame reject) frames transmitted on the port. ::= { x25txstatstable.1.7} x25txrejframes syntax: counter access: read only status: mandatory description:number of reject (reject) frames...

  • Page 130

    122 cabletron relay access products x25rxstatstable (statframe.3) x25rxrlpindex syntax: integer ( 1–8 , which correspond to actual rlp numbers 0–7 ) access: read only status: mandatory description:rlp number. ::= { x25rxstatstable.1.1} x25rxportindex syntax: integer ( 1–8 , which correspond to physi...

  • Page 131

    Mi b ref erence 123 x25rxdmframes syntax: counter access: read only status: mandatory description:number of dm (disconnect mode) frames received on the port. ::= { x25rxstatstable.1.6} x25rxfrmrframes syntax: counter access: read only status: mandatory description:number of frmr (frame reject) frame...

  • Page 132

    124 cabletron relay access products x25rxinfoframes syntax: counter access: read only status: mandatory description:number of info (information) frames received on the port. ::= { x25rxstatstable.1.11} statt1 (statgroup.7) this is the statistics group for t1 channels. T1statsrlpindex syntax: integer...

  • Page 133

    Mi b ref erence 125 description:total transmitted frames. ::= { statt1.1.1.4 } t1statslcvcnt syntax: counter access: read only status: mandatory description:number of bipolar violations and excessive zeroes received on the port. ::= { statt1.1.1.5 } t1statspcvrerrs syntax: counter access: read only ...

  • Page 134

    126 cabletron relay access products description:yellow alarm count. ::= { statt1.1.1.9 } t1statsredalarms syntax: counter access: read only status: mandatory description:red alarm count. ::= { statt1.1.1.10 } t1statsrcvusage syntax: counter access: read only status: mandatory description:receive por...

  • Page 135

    Mi b ref erence 127 t1statsrcvoverruns syntax: counter access: read only status: mandatory description:number of received overrun errors. ::= { statt1.1.1.15 } t1statsrcverrors syntax: counter access: read only status: mandatory description:total bad receives on the t-1 port. ::= { statt1.1.1.16 } t...

  • Page 136

    128 cabletron relay access products ds0astatschannelindex status: integer ( 1–24 ) access: read only status: mandatory description:channel number. ::= {statdsoa.1.1.3} ds0astatsxmitframes status: counter access: read only status: mandatory description: total transmitted frames. ::= {statdsoa.1.1.4} ...

  • Page 137

    Mi b ref erence 129 description: total receive errors. ::= {statdsoa.1.1.9} statvoice (statgroup.9) this is the statistics group for voice. Voicestatsrlpindex syntax: integer ( 1 ) access: read only status: mandatory description:rlp number. This entry is not applicable, but is included for consisten...

  • Page 138

    130 cabletron relay access products status: mandatory description:number of call accepts received from the network. ::= { statvoice.1.1.5 } voicestatstxcallsaccepts syntax: counter access: read only status: mandatory description:number of call accepts transmitted to the network. ::= { statvoice.1.1....

  • Page 139

    Mi b ref erence 131 voicestatsrxcongestions syntax: counter access: read only status: mandatory description:number of congestion management frames received. ::= { statvoice.1.1.11 } voicestatstxcongestions syntax: counter access: read only status: mandatory description:number of congestion managemen...

  • Page 140

    132 cabletron relay access products status: mandatory description:threshold for the statistic rlpstatsqmessages , which is the number of frames queued on the rlp. (this corresponds to the database parameter number of queued messages .) if the measured value for the statistic crosses the threshold (i...

  • Page 141

    Mi b ref erence 133 threshold (in either direction), an alarm is generated. ::= { rlpthreshtable.1.6} rlpthreshrtxframespersec syntax: integer ( 0–65535 ) access: read only status: mandatory description:per-second threshold for the statistic rlpstatsframeretransmits , which is the number of frames r...

  • Page 142

    134 cabletron relay access products sec .) if the measured value for the statistic crosses the threshold (in either direction), an alarm is generated. ::= { portthreshtable.1.3} portthreshtxframespersec syntax: integer ( 0–65535 ) access: read only status: mandatory description:per-second threshold ...

  • Page 143

    Mi b ref erence 135 portthreshlogrejpersec syntax: integer ( 0–65535 ) access: read only status: mandatory description:per-second threshold for the statistic portstatslogicalrejects , which is the sum of rejects and frame rejects on the port. (this corresponds to the database parameter logical rejec...

  • Page 144

    136 cabletron relay access products value for the statistic crosses the threshold (in either direction), an alarm is generated. ::= { portthreshtable.1.10} portthreshrxpercentutl syntax: integer ( 0–65535 ) access: read only status: mandatory description:threshold for the statistic portstatsinpercen...

  • Page 145

    Mi b ref erence 137 traffic types may be bridged. When no , only llc2 terminated traffic is allowed on bridge interfaces. ::{ bridge.3 } bridgemaxsizeforwardingtable syntax: integer ( 128–65535 ) access: read/write status: mandatory description:number of entries allowed in the bridge forwarding tabl...

  • Page 146

    138 cabletron relay access products description:operational value of bridgeadminsrbid . ::{ bridge.8 } bridgedefaultethernetframetype syntax: integer { type-ii ( 1 ), ieee8023 ( 2 )} access: read/write status: mandatory description:default frame type to be used when forwarding traffic on ethernet in...

  • Page 147: Mib Ii Groups

    Mi b ref erence 139 mib ii groups system group (mib-2.1) sysdescr syntax: displaystring access: read only description:description of the node, including name, hardware type, and software operating system. ::= { system.1} sysobjectid object-type syntax: object identifier access: read only status: man...

  • Page 148

    140 cabletron relay access products syscontact syntax: displaystring (0–255 bytes) access: read/write description:contact person for the node. This parameter is specified in the database in snmp system defaults. ::= { system.4} sysname syntax: displaystring (0–255 bytes) access: read/write descripti...

  • Page 149

    Mi b ref erence 141 interfaces group (mib-2.2) ifnumber syntax: integer access: read only description:number of network interfaces configured/defined for this node. This includes each physical port, logical port, and ip interface. ::= { interfaces.1} ifindex syntax: integer access: read only descrip...

  • Page 150

    142 cabletron relay access products ifmtu syntax: integer access: read only description:size (in bytes) of the largest datagram that can be trans- mitted on the interface. ::= { interfaces.2.1.4} ifspeed syntax: gauge access: read only description:current line speed (in bits per second) over the int...

  • Page 151

    Mi b ref erence 143 ifinoctets syntax: counter access: read only description:number of octets (including framing characters) received on the interface. ::= { interfaces.2.1.10} ifinucastpkts syntax: counter access: read only description:for ip interfaces is the number of unicast packets delivered to...

  • Page 152

    144 cabletron relay access products ifinunknownprotos syntax: counter access: read only description:for ip interfaces is the number of received packets that subsequently were discarded due to an unknown or unsupported protocol, and for non-ip interfaces is 0. ::= { interfaces.2.1.15} ifoutoctets syn...

  • Page 153

    Mi b ref erence 145 ifouterrors syntax: counter access: read only description:for ip interfaces is the number of outbound packets discarded due to physical errors, and for non-ip interfaces is the transmit error ratio (the ratio of transmitted frames per second to successfully transmitted frames per...

  • Page 154

    146 cabletron relay access products ip header of datagrams originated at this entity, whenever a ttl value is not supplied by the transport layer protocol. ::= { ip.2 } ipinreceives syntax: counter access: read only status: mandatory description:total number of input datagrams received from interfac...

  • Page 155

    Mi b ref erence 147 their final ip destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities which do not act as ip gateways, this counter will include only those packets which were source-routed via this entity, and the source-route...

  • Page 156

    148 cabletron relay access products ipoutrequests syntax: counter access: read only status: mandatory description:the total number of ip datagrams which local ip user protocols (including icmp) supplied to ip in requests for transmission. Note that this counter does not include any datagrams counted...

  • Page 157

    Mi b ref erence 149 are held while they are awaiting reassembly at this entity. ::= { ip.13 } ipreasmreqds syntax: counter access: read only status: mandatory description:number of ip fragments received that needed to be reassembled at this entity. ::= { ip.14 } ipreasmoks syntax: counter access: re...

  • Page 158

    150 cabletron relay access products ipfragfails syntax: counter access: read only status: mandatory description:number of ip datagrams that have been discarded because they needed to be fragmented at this entity but could not be, e.G., because their don't fragment flag was set. ::= { ip.18 } ipfragc...

  • Page 159

    Mi b ref erence 151 ipadentnetmask syntax: ipaddress access: read only status: mandatory description:subnet mask associated with the ip address of this entry. The value of the mask is an ip address with all the network bits set to 1 and all the hosts bits set to 0 . ::= { ip.20.1.3 } ipadentbcastadd...

  • Page 160

    152 cabletron relay access products ip routing table (ip.21) the ip routing table contains an entry for each route presently known to this entity. Iproutedest syntax: ipaddress access: read/write status: mandatory description:destination ip address of this route. An entry with a value of 0.0.0.0 is ...

  • Page 161

    Mi b ref erence 153 status: mandatory description:alternate routing metric for this route. The semantics of this metric are determined by the routing protocol specified in the route's iprouteproto value. If this metric is not used, its value should be set to -1 . ::= { ip.21.1.4 } iproutemetric3 syn...

  • Page 162

    154 cabletron relay access products (network/subnetwork) ( 3 ), indirect (route to a non-local host/network/sub-network ( 4 )} } access: read/write status: mandatory description:type of route. Note that the values direct( 3 ) and indirect( 4 ) refer to the notion of direct and indirect routing in th...

  • Page 163

    Mi b ref erence 155 12 = bbnspfigp 13 = ospf 14 = bgp ::= { ip.21.1.9 } iprouteage syntax: integer access: read/write status: mandatory description:time (in seconds) since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except thr...

  • Page 164

    156 cabletron relay access products this metric are determined by the routing protocol specified in the route's iprouteproto value. If this metric is not used, its value should be set to -1 . ::= { ip.21.1.12 } iprouteinfo syntax: object identifier access: read only status: mandatory description:ref...

  • Page 165

    Mi b ref erence 157 description:media-dependent `physical' address. ::= { ip.22.1.2 } ipnettomedianetaddress syntax: ipaddress access: read/write status: mandatory description: ipaddress corresponding to the media-dependent `physical' address. ::= { ip.22.1.3 } ipnettomediatype syntax: integer { oth...

  • Page 166

    158 cabletron relay access products icmp group (mib-2.5) icmpinmsgs syntax: counter access: read only status: mandatory description:total number of icmp messages which the entity received. Note that this counter includes all those counted by icmpinerrors . ::= { icmp.1 } icmpinerrors syntax: counter...

  • Page 167

    Mi b ref erence 159 description:number of icmp parameter problem messages received. ::= { icmp.5 } icmpinsrcquenchs syntax: counter access: read only status: mandatory description:number of icmp source quench messages received. ::= { icmp.6 } icmpinredirects syntax: counter access: read only status:...

  • Page 168

    160 cabletron relay access products icmpintimestampreps syntax: counter access: read only status: mandatory description:number of icmp timestamp reply messages received. ::= { icmp.11 } icmpinaddrmasks syntax: counter access: read only status: mandatory description:number of icmp address mask reques...

  • Page 169

    Mi b ref erence 161 may be no types of error which contribute to this counter's value. ::= { icmp.15 } icmpoutdestunreachs syntax: counter access: read only status: mandatory description:number of icmp destination unreachable messages sent. ::= { icmp.16 } icmpouttimeexcds syntax: counter access: re...

  • Page 170

    162 cabletron relay access products icmpoutechos syntax: counter access: read only status: mandatory description:number of icmp echo (request) messages sent. ::= { icmp.21 } icmpoutechoreps syntax: counter access: read only status: mandatory description:number of icmp echo reply messages sent. ::= {...

  • Page 171

    Mi b ref erence 163 icmpoutaddrmaskreps syntax: counter access: read only status: mandatory description:number of icmp address mask reply messages sent. ::= { icmp.26 }.

  • Page 172: Frame Relay (Rfc1315) Mib

    164 cabletron relay access products frame relay (rfc1315) mib frdlcmiifindex syntax: integer access: read only description:ifindex value of corresponding ifentry. ::= { frame-relay.1.1.1} frdlcmistate syntax: integer ( 1–3 ) access: read/write description:type of frame relay management configured: 1...

  • Page 173

    Mi b ref erence 165 frdlcmifullenquiryinterval syntax: integer ( 1–255 ) access: read/write description:number of polling intervals that can pass before issuance of a full status enquiry. ::= { frame-relay.1.1.6} frdlcmierrorthreshold syntax: integer ( 1–10 ) access: read/write description:number of...

  • Page 174: Snadlc (Rfc1747) Mib

    166 cabletron relay access products snadlc (rfc1747) mib sdlcportgroup (snadlc.1) sdlcportadmintable (sdlcportgroup.1) sdlcportadminname syntax: displaystring (1–10 characters) max-access: read/write status: current description:defines the physical port to which this interface is assigned. It has im...

  • Page 175

    Mi b ref erence 167 description:specifies whether the sdlc port is to connect to a leased or switched line. A write operation to this administrative value will not take effect until the sdlc port has been cycled inactive. Defval: 1 (leased) ::= { sdlcportadmintable.1.3} sdlcportadmintopology syntax:...

  • Page 176

    168 cabletron relay access products defval: 0 . ::= { sdlcportadmintable.1.6} sdlcportadminpause syntax: timeinterval (in 1/100ths of a second) max-access: read/write status: current description:minimum elapsed time between any two traversals of the poll list for a primary sdlc port. Depending on th...

  • Page 177

    Mi b ref erence 169 sdlcportopertable (sdlcportgroup.2) sdlcportopername syntax: displaystring (1–8 characters) max-access: read only status: current description:defines the physical port to which this interface is assigned. It has implementation-specific significance. ::= { sdlcportopertable.1.1} s...

  • Page 178

    170 cabletron relay access products sdlcportoperistatus syntax: integer { 1 (inactive), 2 (active)} max-access: read only status: current description:initial value of the administrative status ( ifadminstatus ) of this sdlc port at last port start-up. ::= { sdlcportopertable.1.5} sdlcportoperactivto...

  • Page 179

    Mi b ref erence 171 description:exact method for periodically polling failed secondary link station addresses: ● if sdlcportoperslowpollmethod = servlim , then sdlcportoperservlim defines the actual polling characteristics. ● if sdlcportoperslowpollmethod = pollpause , then sdlcportoperslowpolltimer...

  • Page 180

    172 cabletron relay access products sdlcportoperlastmodifytime syntax: timeticks max-access: read only status: current description:value of sysuptime when this port definition was last modified. If the port has not been modified, this value will be 0. ::= { sdlcportopertable.1.11} sdlcportoperlastfa...

  • Page 181

    Mi b ref erence 173 description:number of frames received by this port with invalid link station addresses. ::= { sdlcportstatstable.1.2} sdlcportstatsdwarfframes syntax: counter32 max-access: read only status: current description:number of frames received by this port which were delivered intact by...

  • Page 182

    174 cabletron relay access products sdlcportstatspollrspsout syntax: counter32 max-access: read only status: current description:number of poll responses sent by this port since the port was created. ::= { sdlcportstatstable.1.7} sdlcportstatslocalbusies syntax: counter32 max-access: read only statu...

  • Page 183

    Mi b ref erence 175 status: current description:number of i-frames that have been transmitted by sdlc link stations on this port. This object is initialized to 0 when the port is created. ::= { sdlcportstatstable.1.11} sdlcportstatsoctetsin syntax: counter32 max-access: read only status: current des...

  • Page 184

    176 cabletron relay access products description:number of times the sdlc link stations on this port have deactivated the link as a result of no activity on the link. This object is initialized to 0 when the port is created. ::= { sdlcportstatstable.1.15} sdlcportstatsrnrlimits syntax: counter32 max-...

  • Page 185

    Mi b ref erence 177 port is created. ::= { sdlcportstatstable.1.19} sdlclsgroup (snadlc.2) sdlclsadmintable (sdlclsgroup.1) sdlclsaddress syntax: integer ( 1–255 ) max-access: read-create status: current description:poll address of the secondary link station for this sdlc link. It uniquely identifie...

  • Page 186

    178 cabletron relay access products description:desired state, sdlclsadminstate , of the sdlc link station at link station start-up. Defval: { 2 (active)}. ::= { sdlclsadmintable.1.4} sdlclsadminmaxdatasend syntax: integer32 max-access: read-create status: current description:maximum pdu size that t...

  • Page 187

    Mi b ref erence 179 administered value may not change the operational value, sdlclsoperreplyto , until the link station is cycled inactive. This object only has meaning for sdlc ports where sdlcportadminrole = primary . Defval: { 100 }. ::= { sdlclsadmintable.1.7} sdlclsadminmaxin syntax: integer ( ...

  • Page 188

    180 cabletron relay access products sdlclsadminmodulo syntax: integer { 8, 128 } max-access: read-create status: current description:modulus for an sdlc link station. This modulus determines the size of the rotating acknowledgement window used the sdlc link station pair. A write operation to this ad...

  • Page 189

    Mi b ref erence 181 sequence is a series of retransmitted frames ( data or control) for which no positive acknowledgement is received. The number of retry sequences is controlled by the object sdlclsadminretriesn . The retries per sequence is controlled by the object sdlclsadminretriesm . The object...

  • Page 190

    182 cabletron relay access products sdlclsadminrnrlimit = 0 means there is no limit. The object descriptor contains the name of an ncp configuration parameter, rnrlimit . Note that the value of this object represents 1/100ths of a second while the ncp rnrlimit is represented in minutes. Depending on...

  • Page 191

    Mi b ref erence 183 status: current description:controls the support for transmission and receipt of sim and rim control frames for this link station. The value of this object controls the setting of the transmit-receive capability sent in the xid field. Defval: { 1 (no) } ::= { sdlclsadmintable.1.1...

  • Page 192

    184 cabletron relay access products sdlclsoperrole syntax: integer { 1 (primary), 2 (secondary), 3 (undefined)} max-access: read only status: current description:current role assumed by the link station. The value of sdlclsoperrole is undefined( 3 ) whenever the link station role has not yet been es...

  • Page 193

    Mi b ref erence 185 recovery will be initiated. The object descriptor contains the name of an ncp configuration parameter, replyto . Note that the value of this object represents 1/100ths of a second while the ncp replyto is represented in 1/10ths of a second. This object only has meaning for sdlc p...

  • Page 194

    186 cabletron relay access products sdlclsoperretriesm syntax: integer ( 0–128 ) max-access: read only status: current description:number of retries in a retry sequence for an sdlc link station. A retry sequence is a series of retransmitted frames (data or control) for which no positive acknowledgem...

  • Page 195

    Mi b ref erence 187 reflected by the object sdlclsoperretriesm . ::= { sdlclsopertable.1.11} sdlclsoperrnrlimit syntax: timeinterval (in 1/100ths of a second) max-access: read only status: current description:current length of time that an sdlc link station will allow its adjacent link station to re...

  • Page 196

    188 cabletron relay access products failed. (if the link station has not failed, this value will be 0 .) ::= { sdlclsopertable.1.15} sdlclsoperlastfailcause syntax: integer { 1 (undefined), 2 (rxfrmr), 3 (txfrmr), 4 (noresponse), 5 (protocolerr), 6 (noactivity), 7 (rnrlimit), 8 (retriesexpired)} max...

  • Page 197

    Mi b ref erence 189 sdlclsoperlastfailreplytos syntax: counter32 max-access: read only status: current description:number of times that the replyto timer had expired for an sdlc link station at the time of the last failure. (if the link station has not failed, this value has no meaning.) ::= { sdlcl...

  • Page 198

    190 cabletron relay access products the transmit-receive capability indicator received in the xid image from the adjacent link station. ::= { sdlclsopertable.1.24} sdlclsstatstable (sdlclsgroup.3) sdlclsstatsblusin syntax: counter32 max-access: read only status: current description:total basic link ...

  • Page 199

    Mi b ref erence 191 control, and information field of i-frames only. At link station startup time, this object must be initialized to 0 . ::= { sdlclsstatstable.1.4} sdlclsstatspollsin syntax: counter32 max-access: read only status: current description:total polls received from an adjacent sdlc link...

  • Page 200

    192 cabletron relay access products station startup time, this object must be initialized to 0 . ::= { sdlclsstatstable.1.8} sdlclsstatslocalbusies syntax: counter32 max-access: read only status: current description:total number of times that the local sdlc link station has entered a busy state (rnr...

  • Page 201

    Mi b ref erence 193 sdlclsstatsuiframesin syntax: counter32 max-access: read only status: current description:total ui-frames received from an adjacent sdlc link station since link station startup. ::= { sdlclsstatstable.1.13} sdlclsstatsuiframesout syntax: counter32 max-access: read only status: cu...

  • Page 202

    194 cabletron relay access products sdlclsstatstestsout syntax: counter32 max-access: read only status: current description:total test frames, commands or responses, transmitted to an adjacent sdlc link station since link station startup. ::= { sdlclsstatstable.1.18} sdlclsstatsrejsin syntax: counte...

  • Page 203

    Mi b ref erence 195 sdlclsstatssimsin syntax: counter32 max-access: read only status: current description:total set initialization mode (sim) frames received from an adjacent sdlc link station since link station startup. ::= { sdlclsstatstable.1.23} sdlclsstatssimsout syntax: counter32 max-access: r...

  • Page 204

    196 cabletron relay access products status: current description:total number of disconnect (disc) requests received from an adjacent sdlc link station since link station startup. At link station startup time, this object must be initialized to 0 . ::= { sdlclsstatstable.1.27} sdlclsstatsdiscout synt...

  • Page 205

    Mi b ref erence 197 from an adjacent sdlc link station since link station startup. At link station startup time, this object must be initialized to 0 . ::= { sdlclsstatstable.1.31} sdlclsstatsdmout syntax: counter32 max-access: read only status: current description:total number of disconnect mode (d...

  • Page 206

    198 cabletron relay access products sdlc link station has inactivated the link as a result of receiving a frame from its adjacent link station which was in violation of the protocol. At link station startup time, this object must be initialized to 0 . ::= { sdlclsstatstable.1.35} sdlclsstatsactivity...

  • Page 207

    Mi b ref erence 199 description:total number of information frames retransmitted by the remote link station because the n(s) received from that link station indicated that one or more information frames sent by that station were lost. This event causes the first missing information frame of a window...

  • Page 208: Novell Ipx Mib

    200 cabletron relay access products novell ipx mib basic system table (ipx.1.1) ipxbasicsysnetnumber syntax: netnumber access: read/write status: mandatory description:network number portion of the ipx address of this system. ::= {ipxbasicsysentry.3} ipxbasicsysnode syntax: octet string (size(6)) ac...

  • Page 209

    Mi b ref erence 201 headers, including any ipx packet with a size less than the minimum of 30 bytes. ::= {ipxbasicsysentry.7} ipxbasicsysinunknownsockets syntax: counter access: read only status: mandatory description:number of ipx packets discarded because the destination socket was not open. ::= {...

  • Page 210

    202 cabletron relay access products ipxbasicsysnoroutes syntax: counter access: read only status: mandatory description:number of times no route to a destination was found. ::= {ipxbasicsysentry.12} ipxbasicsysoutrequests syntax: counter access: read only status: mandatory description:number of ipx ...

  • Page 211

    Mi b ref erence 203 ipxbasicsysconfigsockets syntax: integer access: read only status: mandatory description:the configured maximum number of ipx sockets that may be open at one time. ::= {ipxbasicsysentry.17} ipxbasicsysopensocketfails syntax: counter access: read only status: mandatory description...

  • Page 212

    204 cabletron relay access products defval { 64 } ::= {ipxadvsysentry.3} ipxadvsysintoomanyhops syntax: counter access: read only status: mandatory description:number of ipx packets discarded due to exceeding the maximum hop count. ::= {ipxadvsysentry.4} ipxadvsysinfiltered syntax: counter access: r...

  • Page 213

    Mi b ref erence 205 ipxadvsysoutfiltered syntax: counter access: read only status: mandatory description:number of outgoing ipx packets discarded due to filtering. ::= {ipxadvsysentry.9} ipxadvsysoutcompressdiscards syntax: counter access: read only status: mandatory description:number of outgoing i...

  • Page 214

    206 cabletron relay access products static routes table (ipx.3.2) ipxstaticroutesysinstance syntax: integer access: read/write status: mandatory description:the unique identifier of the instance of ipx to which this row corresponds. ::= {ipxstaticrouteentry.1} ipxstaticroutecircindex syntax: integer...

  • Page 215

    Mi b ref erence 207 ipxstaticroutehopcount syntax: integer access: read/write status: mandatory description:the number of hops necessary to reach the destination. ::= {ipxstaticrouteentry.6} services table (ipx.4.1) ipxservsysinstance syntax: integer access: read only status: mandatory description:t...

  • Page 216

    208 cabletron relay access products ipxservnetnum syntax: netnumber access: read only status: mandatory description:the ipx network number portion of the ipx address of the service. ::= {ipxserventry.5} ipxservnode syntax: octet string (size(6)) access: read only status: mandatory description:the no...

  • Page 217

    Mi b ref erence 209 802.1d bridge (rfc1493) mib dot1dbase (dot1dbridge.1) dot1dbasebridgeaddress syntax: macaddress access: read only status: mandatory description:the mac address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smal...

  • Page 218

    210 cabletron relay access products dot1dbaseport syntax: integer ( 1–65535 ) access: read only status: mandatory description:the port number of the port for which this entry contains bridge management information. ::= { dot1dbase.4.1.1 } dot1dbaseportifindex syntax: integer access: read only status...

  • Page 219

    Mi b ref erence 211 dot1dbaseportmtuexceededdiscards syntax: counter access: read only status: mandatory description:number of frames discarded by this port due to an excessive size. It is incremented by both transparent and source route bridges. Reference: ieee 802.1d-1990: section 6.6.1.1.3 ::= { ...

  • Page 220

    212 cabletron relay access products dot1dstptimesincetopologychange syntax: timeticks (in hundredths of a second) access: read only status: mandatory description:time since the last time a topology change was detected by the bridge entity. Reference: ieee 802.1d-1990: section 6.8.1.1.3 ::= { dot1dst...

  • Page 221

    Mi b ref erence 213 dot1dstprootport syntax: integer access: read only status: mandatory description:port number of the port which offers the lowest cost path from this bridge to the root bridge. Reference: ieee 802.1d-1990: section 4.5.3.3 ::= { dot1dstp.7 } dot1dstpmaxage syntax: timeout (in hundr...

  • Page 222

    214 cabletron relay access products dot1dstpforwarddelay syntax: timeout (in hundredths of a second) access: read only status: mandatory description:this time value controls how fast a port changes its spanning state when moving toward the forwarding state. The value determines how long the port sta...

  • Page 223

    Mi b ref erence 215 reference: ieee 802.1d-1990: section 4.5.3.9 ::= { dot1dstp.13 } dot1dstpbridgeforwarddelay syntax: timeout ( 400–3000 ) access: read/write status: mandatory description:value that all bridges use for forwarddelay when this bridge is acting as the root. Note that 802.1d-1990 spec...

  • Page 224

    216 cabletron relay access products dot1dstpportstate syntax: integer { 1 (disabled), 2 (blocking), 3 (listening), 4 (learning), 5 (forwarding), 6 broken)} access: read only status: mandatory description:the port's current state as defined by application of the spanning tree protocol. This state con...

  • Page 225

    Mi b ref erence 217 root in the configuration bpdus transmitted by the designated bridge for the segment to which the port is attached. Reference: ieee 802.1d-1990: section 4.5.5.4 ::= { dot1dstpporttable.1.6 } dot1dstpportdesignatedcost syntax: integer access: read only status: mandatory descriptio...

  • Page 226

    218 cabletron relay access products learning state to the forwarding state. ::= { dot1dstpporttable.1.10 } dot1dtp group (dot1dbridge.4) the dot1dtp group is optional is implemented by those bridges that support the trans- parent bridging mode. A transparent or srt bridge will implement this group. ...

  • Page 227

    Mi b ref erence 219 dot1dtpfdbtable (dot1dtp.3) this is the forwarding database for transparent bridges. Dot1dtpfdbaddress syntax: macaddress access: read only status: mandatory description:unicast mac address for which the bridge has forwarding and/or filtering information. Reference: ieee 802.1d-1...

  • Page 228

    220 cabletron relay access products to determine if and how frames addressed to the value of the corresponding instance of dot1dtpfdbaddress are being forwarded. Invalid(2): this entry is not longer valid (e.G., it was learned but has since aged-out), but has not yet been flushed from the table. Lea...

  • Page 229

    Mi b ref erence 221 802.3 ethernet (rfc1643) mib statistics dot3statsindex syntax: integer access: read only status: mandatory description:index value that uniquely identifies an interface to an ethernet-like medium. The interface identified by a particular value of this index is the same interface ...

  • Page 230

    222 cabletron relay access products layer management, counted exclusively according to the error status presented to the llc. Reference: ieee 802.3 layer management ::= { dot3statsentry.3 } dot3statssinglecollisionframes syntax: counter access: read only status: mandatory description:count of succes...

  • Page 231

    Mi b ref erence 223 reference: ansi/ieee std 802.3-1985 carrier sense multiple access with collision detection access method and physical layer specifications ::= { dot3statsentry.6 } dot3statsdeferredtransmissions syntax: counter access: read only status: mandatory description:count of frames for w...

  • Page 232

    224 cabletron relay access products dot3statsinternalmactransmiterrors syntax: counter access: read only status: mandatory description:count of frames for which transmission on a particular interface fails due to an internal mac sublayer transmit error. A frame is only counted by an instance of this...

  • Page 233

    Mi b ref erence 225 counted exclusively according to the error status presented to the llc. Reference: ieee 802.3 layer management dot3statsinternalmacreceiveerrors syntax: counter access: read only status: mandatory description:count of frames for which reception on a particular interface fails due...

  • Page 234

    226 cabletron relay access products 802.5 token ring (rfc1748) mib statistics dot5statsifindex syntax: integer access: read only status: mandatory description:identifies the 802.5 interface for which this entry contains management information. The value of this object for a particular interface has ...

  • Page 235

    Mi b ref erence 227 and then receives another smp frame with a is equal to c is equal to 0 without first receiving an amp frame. It denotes a station that cannot set the ac bits properly. ::= { dot5statsentry.4 } dot5statsaborttranserrors syntax: counter access: read only status: mandatory descripti...

  • Page 236

    228 cabletron relay access products dot5statsreceivecongestions syntax: counter access: read only status: mandatory description:this counter is incremented when a station recognizes a frame addressed to its specific address, but has no available buffer space indicating that the station is congested....

  • Page 237

    Mi b ref erence 229 dot5statsharderrors syntax: counter access: read only status: mandatory description:the number of times this interface has detected an immediately recoverable fatal error. It denotes the number of times this interface is either transmitting or receiving beacon mac frames. ::= { d...

  • Page 238

    230 cabletron relay access products status: mandatory description:the number of times the interface has detected an open or short circuit in the lobe data path. The adapter will be closed and dot5ringstate will signify this condition. ::= { dot5statsentry.16 } dot5statsremoves syntax: counter access...