Cadel aquos 24 h2O Installation, Use And Maintenance Manual - page 33
33
AQUOS 24 H
2
O
EN
and ash expulsion speed can be increased. This change resolves all the potential problems related to pellets
clogging in the brazier and deposits forming at the bottom of the brazier itself caused by poor quality fuel or fuel
that produces a lot of ashes. The values available are from -30% to +50% with variations of 10 percentage points
at a time. The variation in negative can be used in case the flame is too low
To change the parameter act as follows:
• Press the “menu” button.
• Scroll to "Settings" using the arrows
• Press "menu" to confirm.
• Scroll to "Smoke rpm variation" using the arrows.
• Press "menu" to confirm.
• Modify the % with the + - keys.
• Press "menu" to confirm and "esc" to exit
l - Maximum power
It allows to set the maximum flame limit at which the stove can operate to reach the set temperature target.
To change the power act as follows:
• Press the “menu” button.
• Scroll to "Settings" using the arrows
• Press "menu" to confirm.
• Scroll to "Maximum power" using the arrows.
• Press "menu" to confirm.
• Change the power from 01 to 05 with the + - keys
• Press "menu" to confirm and "esc" to exit
m - Components test
It can only be carried out with the stove switched off, it allows to select the components to be tested:
• Spark plug: it is turned on for a fixed time of 1 minute during which the panel displays the countdown seconds.
• Feed screw: it is powered for a fixed time of 1 minute during which the panel displays the countdown seconds.
• Extractor: it is activated at 2500 rpm for a fixed time of 1 minute during which the panel displays the countdown
seconds.
• Exchanger: it allows to carry out the test in V5 for a fixed time of 1 minute during which the panel displays the
countdown seconds.
• Pump: it is activated for a fixed time of 10 seconds during which the panel displays the countdown.
• 3 way: the 3 way valve is activated for a fixed time of 1 minute during which the panel displays the countdown
seconds.
To activate the "Components test" function (only when the stove is switched off) act as follows:
• Press the “menu” button.
• Scroll to "Settings" using the arrows
• Press "menu" to confirm.
• Scroll to "Components test" using the arrows.
• Press "menu" to confirm.
• Select the test to be performed with the + - keys
• Press "menu" to confirm and "esc" to exit
n - Chimney sweep function
This function can be activated only when the stove is on and with power output and heating operation power
with parameters P5, with fan (if present) in V5. Any loading/smoke ventilation percentage corrections must be
taken into account. This status lasts 20 minutes, the countdown is displayed on the panel. During this interval the
thermostat/puffer/room set point/H20 set point are not taken into account, only the safety shutdown at 85°C
remains active. At any time the technician can interrupt this stage by quickly pressing the on/off key.
To activate the "Chimney sweep" function act as follows:
• Press the “menu” button.
• Scroll to "Settings" using the arrows
• Press "menu" to confirm.
• Scroll to the "Chimney sweep" function using the arrows.
• Press "menu" to confirm.
• Select "On" with the + - keys (Off by default)
• Press "menu" to confirm and "esc" to exit
o - System configuration
To change the system configuration act as follows:
• Press the “menu” button.
• Scroll to "Settings" using the arrows
• Press "menu" to confirm.
• Scroll to "System configuration" using the arrows.
• Press "menu" to confirm.
• Change the configuration from 01 to 05 with the + - keys
• Press "menu" to confirm and "esc" to exit.
p - Season
In configurations 2 and 3, by enabling the "summer" function, the deviation of the 3-way valve to the heating
system is inhibited in order to prevent the radiators from heating up, therefore the flow is always directed towards
the domestic hot water (DHW).
By activating the "summer" option one automatically enables the auto-eco function (it cannot be deactivated).
The room probe/external thermostat are not taken into account.