1. DL manuals
  2. Cambium Networks
  3. Receiver
  4. PTP 820
  5. Installation Manual

Cambium Networks PTP 820 Installation Manual

Other manuals for PTP 820: Manual
Manual is about: Bringing up your first link

Summary of PTP 820

  • Page 1

    Ptp 820 remec adaptor installation guide 1 ptp 820 remec adaptor installation guide this guide explains how to installation ptp820 remec adaptors: n060082l217a ptp820 remec interface antenna adaptor kit, 6 ghz, single pol n110082l125a ptp820 remec interface antenna adaptor kit, 11 ghz, single pol n1...

  • Page 2

    Ptp 820 remec adaptor installation guide 2 exhibition a – installation of remec interface antenna adaptor kit – single pol this guide explains the process for installing an ptp 820c, ptp820s, or rfu-c unit to an antenna using following adaptors: n060082l217a ptp820 remec interface antenna adaptor ki...

  • Page 3

    Ptp 820 remec adaptor installation guide 3 procedure 1. Prior to the installation, check the polarization definition on the antenna. Also check that the o-ring of the antenna is mounted properly. 2. By default, the remec tube is mounted with vertical polarization. If necessary, switch the polarizati...

  • Page 4

    Ptp 820 remec adaptor installation guide 4 3. Mount the o-ring supplied in the ptp 820s/rfu-c remec adaptor kit for single polo on the appropriate place on the tube. Make sure the mounting direction is correct, as shown in the section view. 4. Locate and match the adaptor to the antenna interface..

  • Page 5

    Ptp 820 remec adaptor installation guide 5 5. Lock the four latches.

  • Page 6

    Ptp 820 remec adaptor installation guide 6 for ptp820s/rfu-c direct mount important! Do not remove the transparent pressure window located on the antenna interface. 1 mount the ptp 820s/rfu-c to the remec adaptor, using the four m8 captive screws and washers supplied with the ptp 820s or rfu-c kit, ...

  • Page 7

    Ptp 820 remec adaptor installation guide 7 for ptp820s/rfu-c 1+1 mounting with coupler: important! Do not remove the transparent pressure window located on the antenna interface. 1 mount the two o-rings supplied in the coupler kit and twist on the coupler body, as defined in the coupler kit instruct...

  • Page 8

    Ptp 820 remec adaptor installation guide 8 3 proceed with mounting the rfu-c or ptp 820s radios, as defined in the coupler kit instructions..

  • Page 9

    Ptp 820 remec adaptor installation guide 9 for ptp820c mounting with splitter: 1. Mount the ptp 820c splitter on the adaptor, using the 4 m8 captive screws and washers supplied with the ptp 820c splitter kit, and tighten the screws. 2. Proceed with mounting the ip-20c radio, as described in the spli...

  • Page 10: Adaptor With Circular Tube

    Ptp 820 remec adaptor installation guide 10 exhibition b – installation of remec interface adaptor with circular tube this guide explains the process for installing an ptp 820c, ptp820s, or rfu-c unit to an antenna using following adaptors: n110082l126a ptp820 remec interface antenna adaptor kit, 11...

  • Page 11

    Ptp 820 remec adaptor installation guide 11 for ptp820s/rfu-c or ptp820c 2+0 mounting with omt: important! Do not remove the transparent pressure window located on the antenna interface. 1 mount the omt on the remec adaptor using the four m8 screws and washers supplied in omt kit and tighten the scr...