Campersat autoseek autoskew 1 h4441 build 4441 august 2008 free to air broadcasting satellite receiving systems campersat digital systems campersat autoseek autoskew system 4441 campersat autoskew single lnb campersat autoskew twin lnb supplementary installation handbook august 2008 © 2008 campersat...
Campersat autoseek autoskew 2 h4441 build 4441 august 2008 version 1/2008 installation instructions a utoseek auto skew ci fitting instructions autoseek autoskew it is no problem to fit an autoseek autoskew fully automatic satellite system onto any vehicle. However, you should take care with some sp...
Campersat autoseek autoskew 3 h4441 build 4441 august 2008 shipped items when unpacking you should find the following: plastic bag with: - 5m cable from topbox to receiver - 3 – pin power supply strip (red: +12v, brown: gnd, black: ignition) - tv coaxial cable - scart cable - scart adaptor - operati...
Campersat autoseek autoskew 4 h4441 build 4441 august 2008 2a. Aluminium elbow the cable intake into the aluminium elbow must point to the back of the vehicle to prevent water from coming in whiledriving. It is to your advantage to place the elbow directlyabove or very close to the fitting location ...
Campersat autoseek autoskew 5 h4441 build 4441 august 2008 it holds the remote receiver and a channel number display as well as 2 buttons for local operation. Its location should be visible from the owner’s normal seating position, to ensure proper operation of the remote unit. The remote operates b...
Campersat autoseek autoskew 6 h4441 build 4441 august 2008 check for the correct direction! When you are sure, just stand on the plate with both feet for a few seconds to press it on firmly. Any glue coming out on the sides can be cleaned away. Now put in the 6 screws to give it some additional safe...
Campersat autoseek autoskew 7 h4441 build 4441 august 2008 elbow! Guide the receiver-side end of the cable through the hole. Any cable that is possibly remaining must be placed inside the vehicle. C) clean the elbow and the area around the hole and fix the elbow with glue, similar to the fitting of ...
Campersat autoseek autoskew 8 h4441 build 4441 august 2008 note: +12v/24v is red and common ground is brown b) to interconnect the oyster you should use cables with a diameter of 2.5mm². Use 4mm² if the length of your cables extend beyond 5m. C) always directly connect the system to the vehicle’s ba...
Campersat autoseek autoskew 9 h4441 build 4441 august 2008 8.Safety / ignition off the 3-pin power connector holds a third line, colored black. This is to automatically retract the antenna if the vehicles motor is started. The automatic retraction will avoid any damage to the system if the owner acc...
Campersat autoseek autoskew 10 h4441 build 4441 august 2008 configuration of the receiver in australia operation this procedure is the basic operating procedure and will be become second nature. We have covered a few extra pointers in the commissioning section so feel free to refer to hints and tips...
Campersat autoseek autoskew 11 h4441 build 4441 august 2008 • to switch from receiver 1 to 2, press button a to b & vice versa for receiver 2 to 1 • power up tv and satellite equipment. • set tv system to receive satellite signals. Tv should display searching for signal. It is ok to leave satellite ...
Campersat autoseek autoskew 12 h4441 build 4441 august 2008 the autoskew is now ready to operate. For a first test, just switch on again and wait about a minute, while the system will locate the satellite and will lock onto its transmission. Any details about the operation of the autoskew can be fou...
Campersat autoseek autoskew 13 h4441 build 4441 august 2008 to change satellites from c1 to eg. Pas 8(select tv) please read the following: • press menu and go to oyster digital and press ok. • go to edit settings and press ok. • go to search satellite and press arrow across on your remote control i...
Campersat autoseek autoskew 14 h4441 build 4441 august 2008.
