Cannondale en 14764 Supplemental Owner's Manual - Initial Operation
10
11
E-Series Owner’s Manual Supplement - 129184.PDF
Esp
añol
ITal
Ia
No
NEDER
la
ND
s
FR
aNÇ
aI
s
DEUT
sCH
ENG
lI
sH
Esp
añol
ITal
Ia
No
NEDER
la
ND
s
FR
aNÇ
aI
s
DEUT
sCH
ENG
lI
sH
Initial operation
requirements
The eBike system can only be activated when the following
requirements are met:
■ a sufficiently charged battery pack is inserted (see
operating instructions of the battery pack).
■ The drive HMI is properly inserted in the holder (see
“Inserting and Removing the Drive HMI”, page
English–2).
■ The drive HMI is properly connected (see “Checking the
speed sensor”, page English–2).
switching the eBike system on/off
options for switching on the eBike system:
■ If the drive HMI is already switched on when inserting it in
the holder, the eBike system is automatically switched on.
■ When the drive HMI and the battery pack are inserted,
briefly press the on/off button 5 of the drive HMI once.
■ When the drive HMI is inserted, press the on/off button of
the battery pack (see battery pack operating instructions).
note: When switching on the eBike system, the pedals of the
eBike must not be subject to load, as otherwise the motor
output capacity will be limited. The error message “Release
pedal” is displayed in text indication (c).
If the eBike system was inadvertently switched on with load
applied to the pedals, then switch it off and then on again
without load.
The drive is activated as soon as you step into the pedals
(except when in push-assistance mode, see “switching the
pushassistance mode on/off”, page English–4). The motor
output depends on the settings of the drive HMI.
as soon as you stop pedaling when in normal operation, or
as soon as you have reached a speed of 25 km/h, the assi-
stance from the eBike drive is switched off. The drive is
automatically reactivated as soon you start pedaling again
and the speed is below 25 km/h.
options for switching off the eBike system:
■ press the on/off button 5 of the drive HMI.
■ switch the battery pack off by its on/off button (see
battery pack operating instructions.)
■ Remove the drive HMI out of its holder.
When no power output of the drive is requested for approx. 10
minutes (e. g., because the eBike is parked) and no button of
the drive HMI or operating unit is pressed, the battery pack
automatically switches off to save energy.
Indications and settings of the drive hmI
Power supply of the drive hmI
When the drive HMI is inserted in holder 4, a sufficiently char-
ged battery pack is inserted in the eBike and the eBike system
is switched on, power is supplied to the drive HMI via the
eBike’s battery pack. When the drive HMI is removed from
holder 4, it is supplied with power via an internal battery
pack. If the internal battery pack is low when switching on
the drive HMI, “attach to bike” is displayed for 3 s in text
indication c. afterwards, the drive HMI switches off again. To
recharge the internal battery pack, insert the drive HMI into
the holder 4 (a battery pack must be inserted in the eBike).
switch the eBike battery pack off by its on/off button (see
battery pack operating instructions). The drive HMI can also
be charged via UsB connection. open protective cap 8 for
this. Using a matching UsB cable, connect the UsB port 7
of the drive HMI to a commercially available UsB charger or
to the UsB port of a computer; (5 V charging voltage; max.
500ma charging current). “UsB connected” is displayed in
text indication c of the drive HMI.