D-ILA D-ILA 1080MF1 Installation And Operation Manual - page 27
2
Thelifeoflight-sourcelampsusedforthisunit
isabout2000hours.
• Thelamplifeof2000hoursismerelytheaver-
agelifespanoflight-sourcelampsandwedo
notprovideanyguaranteeforthisfigure.The
lamplifemaynotreach2000hoursdepend-
ingontheoperatingconditions.Deterioration
progressesrapidlywhentheremaininglamp
usagetimeisshort.Getreadyorreplacewith
anewlampunitwhentheaccumulatedusage
timeexceeds1900hours.Dependingonthe
operatingconditions,thelampmayhavetobe
exchangedearlier.Iftheimageisdarkorcolour
toneabnormal,replacethelampassoonas
possible.
• Youcanalsochecktheaccumulatedhoursof
usage.Pleasereferto‘LampTime’inthe‘Infor-
mation’menu.
• Setting‘PowerSave’inthe‘Options’menuto
‘On’doesnotaffecttheusagetimeofthelight-
sourcelamp.
Please consult your authorised dealer
when purchasing a new lamp unit.
Replacement Lamp (Lamp Unit) Part No.:
BHL5008-S
IMPORTANT: The lamp unit resembles
that used in other projectors of this
type. However the lamps are quite
different and the lamp housings
are not interchangeable. Install
only the correct lamp assembly for
this projector: attempting to force
a different lamp unit to fit may
permanently damage the projector
or cause a serious malfunction. It will
also void your warranty.
When the lamp usage time exceeds
1900 hours (but is under 2000 hours)
TheLAMPindicatorlightsupandtheTEMP
indicatorstartsblinkinguponturningonthe
power(standbymode).
A‘Lampreplacement’messagewillbedis-
playedonthescreenwhenprojectionstarts.
• Themessagecanbeclearedbypressingany
buttonontheremotecontrolorthisunit.
When the lamp usage time exceeds
2000 hours (but is under 2010 hours):
TheLAMPindicatorlightsupandtheFAN
indicatorstartsblinkinguponturningonthe
power(standbymode).
Whenthelampusagetimeexceeds2000
hoursduringprojection,a‘Lampreplacement’
messagewillbedisplayedonthescreenwhen
projectionstartsandthe‘Warning’markwill
appearblinking.
• Pressthe[EXIT]buttontoclearthedisplay.
However,thesame
WarningandLamp re-
placementmessageswillbedisplayedafter1
hour.
• Whentheunitisswitchedtothestandbymode
orturnedoffafterthelampusagetimeexceeds
2000hours,itcannotbeswitchedbacktothe
projectionmodeagain.
Inthiscase,replacewithanewlampunitand
resetthelamptime.
When the lamp usage time reaches
2010 hours
Theunitexitsfromtheprojectionmode(operating
mode)andswitchesintocooldownmode.
• TheLAMPindicatorwilllightupandtheTEMP
andFANindicatorswillappearblinking.
• Theprojectionmode(operatingmode)cannot
berestoreduntilanewlampunitisinstalled
andthelamptimereset.
About Lamp Replacement
• Ifthisunitisinstalledinaconstrictedplace,
attemptingtoreplacethelampin situmaybe
difficultorevencauseinjury.Movethisunittoa
placelargeenoughtoperformtheoperation.
• Useonlygenuinereplacementpartsforthe
lampunit.Otherwise,malfunctionmayoccur.
• Neverattempttore-useanoldlampunit.This
maycausemarkedperformancedeteriorationor
lampblowout,whichmaybeexplosive.Broken
piecesofthelampoutsidetheprojectormay
alsobedangerousduringlampunitexchange.
• Donotreplacethelampimmediatelyafterthe
projectorhasbeeninuse.Thetemperatureof
thelampisstillhighandthismaycauseaburn.
Allowacoolingperiodof1hourormorebefore
replacement.
• Beforereplacingthelampunit,pulloutthe
powerplugfromtheoutletontherearofthe
unitwhiletheStandbyindicatorisstillon.Re-
placingalampwiththeplugconnectedtothe
outletmaycauseinjuriesorelectricshocks.
Replacing the Lamp