Dacor EDWH24S Installation Instructions Manual - page 15
13
Installation Instructions
5. Check again that the entire length of the power
cable, water line and drain hose are free of
pinches or kinks.
6. Verify that the dishwasher is level front to back
and side to side inside the cutout. Re-level if
necessary before testing the unit.
Wet Test Checklist
1. Turn on the water supply and wait for five
minutes. Check for plumbing leaks. Tighten
connections if necessary.
NOtE: Improper
installation of the water supply line “O” ring can
cause the water line to leak at the connection.
2. Turn on power to the dishwasher at the circuit
breaker panel or fuse box. Make sure the power
cord is connected to the electrical outlet (if
applicable).
3. Test dishwasher operation by running a rinse
cycle (which takes about four minutes). See
the use and care manual for specific operating
instructions. Check to make sure that the
dishwasher takes in water and drains.
4. Check for leaks under the dishwasher and under
the sink. If any leaks are found, immediately push
the
StARt/StOP button and disconnect power.
If there are leaks under the sink, check the water
supply and drain connections. Reconnect power
and restart the cycle. If the leak is elsewhere,
and a hose extension is installed, check for
a loose connection. If the leak is under the
dishwasher itself, disconnect power and contact
Dacor Distinctive Service (see inside cover of
these instructions).
5. If the dishwasher functions normally, complete
the installation as instructed in the following
sections.
If the dishwasher fails to operate
properly:
• Verify that power is supplied to the dishwasher.
• Check all plumbing connections.
• Check for kinks in the water supply line and the
drain hose.
• Repeat the Wet Test Checklist.
• If the appliance still does not work, contact Dacor
Distinctive Service at (877) 337-3226. Do not
attempt to repair the appliance yourself. If you
need service, be sure to have the model and
serial numbers available when you call. See the
inside cover for location.
Dacor is not responsible for the cost of correcting
problems caused by a faulty installation.
Drain Connection
CAUtION
• For proper dishwasher operation and drainage,
the drain line must be routed through the bottom
of the cabinet and up to the drain or air gap
connection. The drain hose or air gap outlet
must connect above the sink trap.
• If required, the air gap must be installed at
countertop level.
1. If the drain will connect to a waste disposer,
see the disposer manufacturer’s installation
instructions for correct drain hose mounting
techniques. Most disposers have a plug on the
drain line connection that must be removed prior
to attaching the
drain line. Also, any
joints must have a
minimum 5/8” (1.6
cm) inside diameter.
2. Cut the drain hose adapter on the end of the
drain hose to the appropriate size for the air
gap, waste tee, disposer connection or hose
extension.
3. Connect the drain hose to the air gap or directly
to the waste tee or disposer above the sink trap
as shown in one of the examples on page 6.
4. Tighten the holding clamp.
5. For installations with an air gap, make sure that
the drain line between the air gap and the waste
tee or disposer is in place and that it is clamped
tightly on both ends.
6. To ensure proper operation, inspect the drain
system to make sure that:
• No part of the drain hose is higher than 35”
(88.9 cm) from the bottom of the dishwasher.
• The connection to the waste tee or disposer is
a minimum of 20” (50.8 cm) above the bottom
of the dishwasher base.
Verifying Operation
Pre-verification Check List
1. Confirm that the power cable is disconnected.
2. Make sure all packing material has been
removed from inside the dishwasher.
3. Familiarize yourself with operation of the
dishwasher by reading the use and care manual.
4. Remove any protective film, if present from the
control panel, door panel, etc.