Dacor Epicure EGR30 Installation Instructions Manual - Nstallation
WARNINGS:
1.
Do not attempt to disengage the hinge catches
with the door removed from the oven. The hinge
springs could release causing personal injury.
2.
Do not lift or carry the oven door by the door
handle.
i
nsTallaTion
i
nsTRuCTions
e
leCTRiCal
R
equiRemenTs
Open the door to its fully opened position. Rotate the catch over
the retaining arm on each hinge. Lift the oven door to about a 30
degree angle from the horizontal position. Pull the door away from
the oven while continuing to lift.
Grounding Instructions (ERD Models Only)
This appliance must be electrically grounded. With the
range positioned directly in front of the cabinet cutout, feed the
appliance conduit to the electrical junction box. Then, depending
upon local codes, utilize one of the following techniques to
connect the appliance to the electrical power supply:
A.
Connecting to a Four-Wire Electrical System
1.
Separate the green and white appliance wires.
2.
Connect the white
appliance wire to
the neutral (white)
supply wire in the
junction box.
3.
Connect the black
appliance wire
to the black (L1)
power supply wire
in the junction box.
4.
Connect the red
appliance wire to
the red (L2) power
supply wire in the
junction box.
5.
Connect the green
appliance wire to
the green house
grounding wire in
the junction box.
Conduit from
appliance
Cable from
power supply
Wire nut
(4 places)
Junction
box
RED
RED
GREEN
GREEN
WHITE
WHITE
BLACK
BLACK
Connecting the appliance to a
four-wire power supply
Conduit from
appliance
Cable from
power supply
Wire nut
(3 places)
Junction
box
RED
RED
GREEN
WHITE
WHITE
BLACK
BLACK
**Connecting the appliance to a
three-wire power supply
B.
Connecting the Green Appliance Wire to the Neutral (White)
Supply Wire – Where Local Codes Permit
1.
Connect the green and white appliance wires to the neutral (white)
supply wire in the junction box.
2.
Connect the black appliance wire to the black (L1) power supply wire
in the junction box.
3.
Connect the red appliance wire to the red (L2) power supply wire in
the junction box.
C.
Connecting the Green Appliance Wire to a Grounded Supply
Wire or a Grounded Cold Water Pipe – Where Local Codes
Permit.
1.
Separate the green and white appliance wires.
2.
Connect the white appliance wire to the neutral (white) supply wire in
the junction box.
3.
Connect the black appliance wire to the black (L1) power supply wire
in the junction box.
4.
Connect the red appliance wire to the red (L2) power supply wire in
the junction box.
e
leCTRiCal
C
onneCTions
e
leCTRiCal
C
onneCTions
- eRd
m
odel
R
anges
o
nly
To remove door,
rotate catch up.
Lift door up to 30° angle,
then pull door away
from the range oven section.
30°
Hinge Catch
Removing the Oven Door
To remove door,
rotate catch up.
Lift door up to 30° angle,
then pull door away
from the range oven section.
30°
Hinge Catch
WARNINGS:
1. ERD models must be connected to a grounded,
metallic, permanent wiring system. Alternatively,
a grounding conductor should be connected to
the grounding terminal or lead on the appliance.
2.
ERG models must be connected to a grounded
receptacle. Failure to do so may result in an
electrical shock hazard.
3. Do not use an extension cord with this appliance.
Such use may result in fire, electrical shock, or
other personal injury.
4. Do not install a fuse in the neutral or ground
circuit. A fuse in the neutral or ground circuit may
result in an electrical shock hazard.
WARNING
**Do not connect the green appliance wire to the
neutral (white) supply wire unless local building
codes permit.