- DL manuals
- Easymount
- Laminator
- Cold EM-1400
- Product Instruction Manual
Easymount Cold EM-1400 Product Instruction Manual
Summary of Cold EM-1400
Page 1
Product instruction manual easymount wide format laminators the easymount has been designed to be user friendly, however we strongly recommend you take a few minutes to read through this manual to ensure correct operation. Keep this manual safe for future reference..
Page 2
2 contents page 3 - introduction page 4 - safety instructions and environmental requirements page 5 - control panel and specifications page 6 - installation of laminating films page 7 - film loading page 8 - feeding the film and cold laminating page 9 - cold laminating and single hot laminating page...
Page 3
3 introduction thank you for purchasing the easymount laminator. Easymount is a high performance wide format mounting and laminating system with a solid construction built to last. The easymount is great for mounting prints to boards and applying pressure sensitive laminates as well as applying appl...
Page 4
4 safety instructions • please ensure that the voltages of power supply you are using match with rated working voltages before operating the machine • the power supply should be close to the machine for convenient use • the power supply should provide reliable protective earthing connection • this m...
Page 5
5 the control panel em-1200 em-1400 em-1600 max laminating width 1200mm / 47” 1400mm / 55” 1600mm / 63” max laminating thickness 25mm / 1” temperature of rubber roller ambient temperature to 60°c / 140°f approx highest line speed 6m/20ft /min approx lowest line speed 0.7m/2ft /min (adjusting the pre...
Page 6
6 installation of laminating films pressure sensitive film (loaded on the top mandrel) 1. Remove the top mandrel from the mandrel support brackets 5. Re-load the mandrel on to the bracket with the film feeding from the bottom of the mandrel if the film is wound with the film on the outside of off th...
Page 7
7 film loading pressure sensitive film (loaded on the top mandrel) 1. Lift the feed tray to the upright position and lock securely. Following the loading diagram on the left cabinet of the machine, pull the film off the bottom of the mandrel and towards the front of the machine, over the top of the ...
Page 8
8 feeding the film 1. Using the pressure handle raise the upper roller 7. Press the ‘forward’ drive button. The loading card should be pulled through the machine 8. Ensure the top and bottom films match each other and dont overlap left to right. If they dont, loosen the mandrel core grip and slide t...
Page 9
9 5. Ensure that as the film is being drawn over the rollers it is smooth. If it isnt you can apply tension to the film mandrel by turning the core grip adjustment sleeve apply just enough pressure to remove any airpockets or creases 6. Your document can now be fed into the laminator. Place the docu...
Page 10
10 mount film 1. Position the mount film centrally on the mandrel and lift it into position on the brackets 2. Pull the mount film up and towards the bottom roller. Optional extras media brackets 1. 3 media brackets space evenly on cross member 2. Place your roll of media on the brackets and bring l...
Page 11
11 take up unit 1. To fit remove blanking plates from rear of the machine 3. Fit the other bracket in place of the right hand blanking plate 2. Fit motorized bracket in place of the blanking bracket - left hand side looking from the rear of the machine 6. Fit the take up mandrel (note the bracket is...
Page 12
12 trouble shooting problem solution take pressure off rollers and drop down loosely into the neutral position. The media will then correct itself and run through smoothly. Media lifting and wrinkling going through the rollers. This is caused by adding too much roller pressure..
Page 13
13 problem film running loose and climbing up onto the take up core. This occurs when there is no tension added to the film. Firstly, ensure the core collars are tight to the shaft by tightening all 4 screws. Add tension to the film by turning the core collar in the directions shown. This must be do...
Page 14
14 problem media running too tight over the feed tray. This happens when the media is loaded onto the system and fed over the feed tray. Load media on holders supplied with the machine. Solution or run media loosely through the machine. Or run media from the top mandrel at the back of the easymount,...
Page 15
15 problem solution lift rollers. Pull media tightly from the back of the system. This will enable the laminating film and media to ‘coat’ the rollers evenly. Before running, ensure that the film is smooth and tight to the rollers. Drop the rollers down loosely and continue laminating. Creasing on l...
Page 16
16 warranty & incorrect use important information your easymount laminator should reach you in perfect condition and is guaranteed for 1 year from date of purchase covering defective parts and general wear and tear, this does not cover film jams, misfeeds or other operator related errors, which woul...