- DL manuals
- Eaton
- UPS
- Powerware 5125
- User Manual
Eaton Powerware 5125 User Manual - page 34
INSTALLATION
EATON Powerware
®
5125 Two-in-One UPS (2400/3000 VA) User’s Guide
S 164201383 Rev C www.power-
ware.com
28
4.
If you are installing power management software, connect your
computer to the UPS communication port using the supplied
communication cable.
5.
For rack-mount installations only. If your rack has conductors for
grounding or bonding of ungrounded metal parts, connect the
ground cable (not included) to the ground bonding screw.
6.
Plug the equipment to be protected into the appropriate UPS output
receptacles (see page 45 for more information on load segments).
NOTE DO NOT protect laser printers with the UPS because of the exceptionally high power
requirements of the heating elements.
7.
If you installed optional EBMs, remove the breaker tie from all
battery circuit breakers.
Switch all battery circuit breakers to the ON (
|
) position.
8.
For PW5125 3000e and 3000g RM models only. Plug the detachable UPS
power cord into the input connector on the UPS rear panel.
To the other end of the cord, install a 16A plug that meets your local
electrical code requirements for the AC power source.
9.
If an emergency power-off (disconnect) switch is required by local
codes, see the following section, “Remote Emergency Power-off
Installation,” to install the REPO switch before powering on the
UPS.
10. Plug the UPS power cord into a power outlet.
All front panel indicators flash briefly and then only the
μ
indicator
flashes, indicating the UPS is in Standby mode with the equipment
offline. If the alarm beeps or a UPS alarm indicator stays on, see
Table 9 on page 60.
Summary of Powerware 5125
Page 1
Powerware 5125 two-in-one ups 2400/3000 va user’s guide ®.
Page 2
Class a emc statements fcc part 15 note this equipment has been tested and found to comply with the limits for a class a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a c...
Page 3
Requesting a declaration of conformity units that are labeled with a ce mark comply with the following harmonized standards and eu directives: s harmonized standards: en 50091-1-1 and en 50091-2; iec 60950 third edition s eu directives: 73/23/eec, council directive on equipment designed for use with...
Page 4
Special symbols the following are examples of symbols used on the ups or accessories to alert you to important information: risk of electric shock - indicates that a risk of electric shock is present and the associated warning should be observed. Caution: refer to operator’s manual - refer to your o...
Page 5
Eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com i table of contents 1 introduction 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 safety warnings 3 . . . . . . . . . . . . ....
Page 6
Table of contents eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com ii replacing batteries 50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to replace u...
Page 7
Eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 1 chapter 1 introduction the powerware ® 5125 uninterruptible power system (ups) protects your sensitive electronic equipment from basic power problems such as power failures, power sags, power su...
Page 8
Introduction eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 2 s hot-swappable batteries that simplify maintenance by allowing you to replace batteries safely without powering down the critical load. S emergency shutdown control through the rem...
Page 9
Eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 3 chapter 2 safety warnings important safety instructions save these instructions this manual contains important instructions that you should follow during installation and maintenance of the ups ...
Page 10
Safety warnings eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 4 c a u t i o n s batteries can present a risk of electrical shock or burn from high short-circuit current. Observe proper precautions. Servicing should be performed by qualified s...
Page 11
Safety warnings eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 5 a d v a r s e l s batterierne kan give risiko for elektrisk stød eller brandsår forårsaget af høj kortslutningsstrøm. Overhold gældende forsigtighedsregler. Servicering skal udfø...
Page 12
Safety warnings eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 6 s teneinde de kans op brand of elektrische schok te verminderen dient deze ups in een gebouw met temperatuur- en vochtigheidregeling te worden geïnstalleerd, waar geen geleidende...
Page 13
Safety warnings eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 7 tarkeita turvaohjeita tÄrkeitÄ turvaohjeita - suomi sÄilytÄ nÄmÄ ohjeet tämä käyttöohje sisältää tärkeitä ohjeita, joita on noudatettava ups-virtalähteen ja akkujen asennuksen ja...
Page 14
Safety warnings eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 8 consignes de sécurité consignes de sÉcuritÉ importantes conserver ces instructions ce manuel comporte des instructions importantes que vous êtes invité à suivre lors de toute pro...
Page 15
Safety warnings eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 9 a t t e n t i o n ! S les batteries peuvent présenter un risque de choc électrique ou de brûlure provenant d’un courant de court-circuit haute intensité. Observez les précautions...
Page 16
Safety warnings eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 10 s um die brand- oder elektroschockgefahr zu verringern, diese usv nur in gebäuden mit kontrollierter temperatur und luftfeuchtigkeit installieren, in denen keine leitenden schmu...
Page 17
Safety warnings eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 11 a v v e r t e n z a s l’ups contiene la propria fonte di energia (batterie). Le prese d’uscita possono essere sotto tensione anche quando l’ups non è collegato all’alimentazione...
Page 18
Safety warnings eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 12 viktig sikkerhetsinformasion viktige sikkerhetsinstruksjoner gjem disse instruksjonene denne håndboken inneholder viktige instruksjoner som du bør overholde ved montering og ved...
Page 19
Safety warnings eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 13 f o r s i k t i g s batterier kan utgjøre en fare for elektrisk støt eller brannsår pga. Høy kortsluttingsstrøm. Treff passende forholdsregler. Service bør utføres av kvalifiser...
Page 20
Safety warnings eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 14 s para reduzir o risco de incêndios ou choques elétricos, instale a ups em ambiente interno com temperatura e umidade controladas e livres de contaminadores condutíveis. A tempe...
Page 21
Safety warnings eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 15 П Р Е Д У П Р Е Ж Д Е Н И Е s В данном ИБП установлены собственные источники энергии (батареи). На выходных розетках может бытьнапряжение, даже если ИБП не подключен к сети пере...
Page 22
Safety warnings eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 16 advertencias de seguridad instrucciones de seguridad importantes guarde estas instrucciones este manual contiene instrucciones importantes que debe seguir durante la instalación...
Page 23
Safety warnings eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 17 p r e c a u c i Ó n s las baterías pueden constituir un riesgo de descarga eléctrica o quemaduras por corriente alta de corto circuito. Adopte las precauciones debidas. Personal...
Page 24
Safety warnings eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 18 s minska risken för brand eller elektriska stötar genom att installera denna ups-enhet inomhus, där temperatur och luftfuktighet är kontrollerade och där inga ledande förorening...
Page 25
Eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 19 chapter 3 installation this section explains: s equipment inspection s ups internal battery connection s ups setup and installation, including extended battery modules (ebms) s remote emergency...
Page 26
Installation eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 20 connecting the ups internal battery to ensure proper battery operation before installing the ups: 1. Verify that the ups is off and unplugged. 2. Remove the packing material (see f...
Page 27
Installation eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 21 ups setup the powerware 5125 ups is designed for flexible configurations and can be installed in a rack or as a standalone cabinet. If you are installing the ups in a rack, continu...
Page 28
Installation eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 22 note the ups and ebms must be installed at the bottom of the rack. If placed in a rack with existing equipment, the rack must be reconfigured to allow the ups installation at the b...
Page 29
Installation eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 23 the setup varies depending on the number of cabinets you are installing: 1. For one cabinet, the pedestals must be installed. Continue to step 2. For two cabinets, the pedestals an...
Page 30
Installation eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 24 6. Place the ups cabinet horizontally so that the left end of the cabinet is accessible (see figure 10). Figure 10. Installing ups pedestals (for two cabinets) 7. Align the pedesta...
Page 31
Installation eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 25 10. Carefully position the cabinets upright with the air vents at the top (see figure 12 or figure 13). Air vents figure 12. Pedestals with two cabinets note pedestals are required...
Page 32
Installation eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 26 11. Align each joining bracket with the adjacent corner screw holes and secure with the supplied screws (see figure 14). Joining bracket ebm ups joining bracket figure 14. Installi...
Page 33
Installation eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 27 installing the ups note do not make unauthorized changes to the ups or accessories; otherwise, damage may occur to your equipment and void your warranty. Figure 15 shows a typical ...
Page 34
Installation eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 28 4. If you are installing power management software, connect your computer to the ups communication port using the supplied communication cable. 5. For rack-mount installations only...
Page 35
Installation eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 29 11. Press and hold the on button until you hear the ups beep (approximately one second). The μ indicator illuminates solid and the load level indicators display the percentage of l...
Page 36
Installation eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 30 w a r n i n g the repo circuit is an iec 60950 safety extra low voltage (selv) circuit. This circuit must be separated from any hazardous voltage circuits by reinforced insulation....
Page 37
Installation eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 31 4. Reconnect the repo connector to the repo port. 5. Verify that the externally-connected repo switch is not activated to enable power to the ups output receptacles. 6. Plug the up...
Page 38
Installation eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 32 repo port iec 320-c19 receptacle battery connector 16a, iec 320-c20 input connector communication port iec 320-c13 receptacles x-slot communication bay circuit breakers ground bond...
Page 39
Eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 33 chapter 4 operation this section describes: s turning the ups on and off s starting the ups on battery s operating modes turning the ups on after the ups is connected to a power outlet, it ente...
Page 40
Operation eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 34 turning the ups off note pressing the off button while the ups is in battery mode causes the ups to shut down immediately. To turn off the ups: 1. Prepare your equipment for shutdown....
Page 41
Operation eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 35 normal mode during normal mode, the μ indicator illuminates and the front panel displays the percentage of ups load capacity being used by the protected equipment (see figure 22). The...
Page 42
Operation eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 36 bypass mode in the event of a ups overload or internal failure, the ups transfers your equipment to utility power. Battery mode is not available; however, the utility power continues ...
Page 43
Eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 37 chapter 5 configuration when the ups is in configuration mode, the front panel leds represent the configuration options. Use the control buttons (on button, off button, and button) to modify th...
Page 44
Configuration eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 38 4 on button off button alarm reset button configuration mode leds press and hold the on and alarm reset buttons simultaneously to enter configuration mode. 1 2 press the on button...
Page 45
Configuration eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 39 table 1. Configuration mode leds and options configuration mode leds option led status explanation 100/200–208v nominal input voltage on* selecting this option changes the nominal...
Page 46
Configuration eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 40
Page 47
Eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 41 chapter 6 additional ups features this section describes: s x-slot cards s load segments x-slot cards x-slot cards allow the ups to communicate in a variety of networking environments and with ...
Page 48
Additional ups features eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 42 multi-server card relay interface card usb card modbus card x-slot communication bay (single-port card shown) connectups-x web/snmp card figure 24. Optional x-slot cards...
Page 49
Additional ups features eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 43 table 2. Communication port pin assignment pin number signal name function direction from the ups 1 low batt low battery relay contact; 20 ma, 30 vdc contact rating out ...
Page 50
Additional ups features eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 44 on-bypass relay jumper (j3) on-bypass disabled on-bypass enabled as/400 norm figure 27. On-bypass relay jumper 3. To prevent electrostatic discharge (esd), place one han...
Page 51
Additional ups features eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 45 load segments load segments are sets of receptacles that can be controlled by power management software, providing an orderly shutdown and startup of your equipment. For...
Page 52
Additional ups features eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 46.
Page 53
Eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 47 chapter 7 ups maintenance this section explains how to: s care for the ups and batteries s replace the electronics module s replace the batteries s recycle used batteries or ups ups and battery...
Page 54
Ups maintenance eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 48 replacing the electronics module the electronics module can be hot-swapped for easy replacement without losing power to your equipment. The ups automatically switches to bypass ...
Page 55
Ups maintenance eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 49 note to prevent power loss to your equipment, follow step 4 closely. 4. While inserting the new electronics module, press and hold the button for approximately five seconds or u...
Page 56
Ups maintenance eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 50 replacing batteries note do not disconnect the batteries while the ups is in battery mode. With the hot-swappable battery feature, ups batteries can be replaced easily without t...
Page 57
Ups maintenance eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 51 2. Unscrew three nuts (one in the upper left corner and two on the bottom of the bracket) and set aside the battery retaining bracket (see figure 33). Figure 33. Removing the ba...
Page 58
Ups maintenance eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 52 how to replace extended battery modules c a u t i o n the ebms are heavy (see page 55). A minimum of two people are required to lift the cabinets into the rack. To replace the e...
Page 59
Ups maintenance eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 53 ups battery connector ebm battery connectors joining brackets ebm cables on off battery circuit breaker figure 35. Ebm connections recycling the used battery or ups contact your...
Page 60
Ups maintenance eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 54.
Page 61
Eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 55 chapter 8 specifications this section provides the following specifications: s model list s weights and dimensions s electrical input and output s environmental and safety s battery table 3. Mo...
Page 62
Specifications eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 56 table 5. Technical specifications low voltage models high voltage models operating frequency 50/60 hz, auto-sensing frequency range 46–64 hz noise filtering movs and line filter ...
Page 63
Specifications eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 57 table 7. Battery ups configuration (10) 12v, 5 ah internal batteries ebm configuration pw5125 120 ebm: 120v, 30a type sealed, maintenance-free, valve-regulated, lead-acid chargin...
Page 64
Specifications eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 58.
Page 65
Eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 59 chapter 9 troubleshooting this section explains: s ups alarms and conditions s how to silence an alarm s service and support audible alarms and ups conditions the ups has an audible alarm featu...
Page 66
Troubleshooting eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 60 table 9. Troubleshooting guide alarm or condition possible cause action the indicator is not on; the ups does not start. μ the power cord is not connected correctly. Check the p...
Page 67
Troubleshooting eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 61 action possible cause alarm or condition the ups is on battery due to a utility failure. The ups is powering the equipment with battery power. Prepare your equipment for shutdow...
Page 68
Troubleshooting eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 62 action possible cause alarm or condition power requirements exceed ups capacity (103 to 110% for 30 seconds) or the load is defective. Turn off and unplug the ups. Remove some o...
Page 69
Troubleshooting eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 63 service and support if you have any questions or problems with the ups, call your local distributor or the help desk at one of the following telephone numbers and ask for a ups ...
Page 70
Troubleshooting eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 64.
Page 71
Eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 65 chapter 10 warranty two-year limited warranty (us and canada) powerware ups models: 5110, 5115, and 5125 warrantor: the warrantor for the limited warranties set forth herein is eaton electrical...
Page 72
Warranty eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 66 what this limited warranty does not cover: this warranty does not cover any defects or damages caused by: (a) failure to properly store the product before installation, including the c...
Page 73
Warranty eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 67 costs not related to warranty: the end-user shall be invoiced for, and shall pay for, all services not expressly provided for by the terms of this warranty, including without limitatio...
Page 74
Warranty eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 68 what this limited warranty does not cover: this warranty does not cover any defects or damages caused by: (a) failure to properly store the product before installation, including the c...
Page 75
Warranty eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 69 other limitations: company’s obligations under this warranty are expressly conditioned upon receipt by company of all payments due to it (including interest charges, if any). During su...
Page 76
Warranty eaton powerware ® 5125 two-in-one ups (2400/3000 va) user’s guide s 164201383 rev c www.Power- ware.Com 70 what this guaranty does not cover: any reimbursement or repair to end-user’s equipment does not include reimbursement for or restoration of any data loss. This guaranty does not cover ...