Eberspächer B1LC compact Operating Instructions Manual

Other manuals for B1LC compact: Operating Instructions Manual
Manual is about: Engine-independent air heaters

Summary of B1LC compact

  • Page 1

    Air heaters b1lc compact /d1lc compact technical description eb e rsp a c h e r ' operating instructions installation instructions j . Eberspa-sher gmbh & co. Eoerspachersr.R 24 d -7373q esslingen tole-fon (2entral) (0711)9 39-03 telefax (0? 11)939-0500 vwrt.Cberspaechw.Dq engine-independent air hea...

  • Page 2

    Contents page scope of delivery / cat nos................................................. 2 government regulations...................................................... 4 safety instructions................................................................ 4 typical installation / installation p o si...

  • Page 3

    Scope of delivery d 1 l c compact complete version 25 1978 05 00 00 as shown without pos. Z version 25 1979 05 00 00 as shown without pos. Y.

  • Page 4

    Parts without item no. = universal installation kit without additional parts x and y vv\.

  • Page 5

    Government regulations concerning installation for installation in motor vehicles that are subject to the regulations authorising the use of vehicles for road traffic (stvzo), the air heater has been approved by the (german) federal office for motor traffic in keeping with the "general model approva...

  • Page 6

    Installation instructions the suggestions put forward in these installation instruc­ tions are only examples. Possibilities other than those illu ­ strated (e.G. In the selection of the installation position or means of running air) are also permissible provided they meet the requirements of the wes...

  • Page 7

    Installing the heater the b 1 l c c o m p a c t! D 1 l c compact heaters are suitable and approved fo r installation in vehicle areas used by per­ sons. Installation in the driver or passenger areas of motor buses* is not permitted. The electronic control device is integrated in the heater. This fac...

  • Page 8

    Fastening to the vehicle wall/floor make penetrations in accordance with the template pattern. The hoie for the cable leading to the metering pump is not in­ cluded in the template and must be drilled to suit the installa­ tion method. The mating surface for the heater base must be smooth. To drill ...

  • Page 9

    Running the combustion air/running the exhaust permissible diameters, lengths, bends of combustion air and exhaust lines. Silencer (optional) r t f min. 0,2-max.2m protect from slipstream, snow, dirt and water. Combustion air silencer (optional) r t t min. 0,2 -max. 2m exhaust ■©. R f protect from s...

  • Page 10

    Fuel supply divergences from the instructions set forth here are not permitted, as they can iead to malfunctions. 1. For cars w ith diesel engines, and fo r cars w ith p etrol engines having m echanical pump. Fuel tapped from the fuel supply line to the engine. Precondition: the fuel line from the f...

  • Page 11

    3. Permissible suction and pressure heads for installation per 1„and 2.; permissible positioning of metering pump max. Fuel level fuel line connection to heater metering pump min.Fuel level supply pressure from tank to metering pump: e = max. 3000 mm suction head: tank at zero pressure f = max. 500 ...

  • Page 12

    Heating operation at high altitudes: up to 1500 m: unrestricted heating operation, above 1 500 m: heating operation is possible during a short stay (e.G. Crossing a mountain pass, taking a rest). If a longer stay is planned (e.G. Winter camping), the fuel has to be adapted to the altitude. In this c...

  • Page 13

    Wiring diagram heater, normal version parts list cable colours sw = black ws = white rt = red ge = yellow gn = green vi = violet br = brown gr = grey bl = blew li = purple 25 1976 00 96 01 b 1.1 1.2 1.5 1.12 2.1 2.2 2.7 2.7.1 5.1 burner motor glow plug overheating sensor flame sensor controller dosi...

  • Page 15

    Wiring diagram heater, version adr / trs 003 / tmd t ~ r r m ~ n r r r t t i ~ t i 1 2 3 4 5 6 7 8 9 10 !! 12 13 14 parts list gd 1.1 burner motor 1.2 glow plug 1.5 overheating sensor 1.12 flame sensor 2.1 controller 2.2 dosing pump 2.7 main fuse 12 volt = 25 a; 24 volt = 15 a 2.7.1 fuse, actuation ...

  • Page 17

    Functional d escrip tion controls 1. Operating unit the operating unit is for switching the heater on and off and for setting the desired cabin temperatures (intake air temperature between 10 °c and 30 °c). The integrated green led indicates wheter the heater is on. 2. Heater timer (optional) with t...

  • Page 18

    Sectional draw ing 12v 25a 1 hot air blower wheel 11 ouiercasing f = fresh air 2 blower motor 12 exhaust line 3 comb usti on ai r blowe r whee i 13 flange seal v = combustion air 4 glow plug 14 fuel line 5 control unit 15 main fuse 8 = fuel 6 safety thermal cutout switch 16 combustion air intake lin...