Ecoteck ILARIA Operation And Maintenance Manual - page 13
MANUAL
ILARIA
MANUAL
MANUAL
MANUAL
ILARIA
ILARIA
ILARIA
3- Unwind the room probe on the rear of the stove, making sure it doesn’t rest on hot surfaces.
4- Correctly connect the pellet stove to the flue.
5- Fill the hopper with pellets (diameter 6 mm).
6- Open the door and check that the firepot is properly in position and that the flame trap is in place,
towards the top of the combustion chamber.
7- Close the door. Never open the door when the pellet stove is on.
8- Connect the stove to a power socket using the special cable supplied.
9- Move the switch located behind the stove to position “1”.
10- Load the pellets, as described in the corresponding chapter.
11- Press the start button for 2 seconds; the control unit will start the ignition cycle.
5.3.2. Possible problems when starting for the first time
No flame forms: When starting for the first time, too few pellets may fall into the firepot, thus
preventing the flame from lighting.
Solution: Open the door and empty the firepot. Replace the firepot in position and press the start
button again. The ignition phase will recommence from the beginning.
IMPORTANT:
When starting for the first time make sure the room is well ventilated, as in the first few hours of
operation unpleasant odours may be produced due to the fumes from the paint and the grease in
the tube bundle.
6. Tips
Do not switch the stove on intermittently. This may cause sparks that shorten the life of the electrical
components.
Do not touch the stove with wet hands. The stove contains electrical components, and may
cause discharges if not handled correctly. Only authorised technicians can resolve any operating
problems.
Do not remove any screws from the combustion chamber if they have not first been properly
lubricated.
Check that the firepot is correctly positioned.
For any other problems contact your ecoteck installer
3- Unwind the room probe on the rear of the stove, making sure it doesn’t rest on hot surfaces.
4- Correctly connect the pellet stove to the flue.
5- Fill the hopper with pellets (diameter 6 mm).
6- Open the door and check that the firepot is properly in position and that the flame trap is in place,
towards the top of the combustion chamber.
7- Close the door. Never open the door when the pellet stove is on.
8- Connect the stove to a power socket using the special cable supplied.
9- Move the switch located behind the stove to position “1”.
10- Load the pellets, as described in the corresponding chapter.
11- Press the start button for 2 seconds; the control unit will start the ignition cycle.
5.3.2. Possible problems when starting for the first time
No flame forms: When starting for the first time, too few pellets may fall into the firepot, thus
preventing the flame from lighting.
Solution: Open the door and empty the firepot. Replace the firepot in position and press the start
button again. The ignition phase will recommence from the beginning.
IMPORTANT:
When starting for the first time make sure the room is well ventilated, as in the first few hours of
operation unpleasant odours may be produced due to the fumes from the paint and the grease in
the tube bundle.
6. Tips
Do not switch the stove on intermittently. This may cause sparks that shorten the life of the electrical
components.
Do not touch the stove with wet hands. The stove contains electrical components, and may
cause discharges if not handled correctly. Only authorised technicians can resolve any operating
problems.
Do not remove any screws from the combustion chamber if they have not first been properly
lubricated.
Check that the firepot is correctly positioned.
For any other problems contact your ecoteck installer
-12-
-12-
-19-
-19-
7.5. Menu functions
To access the menus, hold P4 for 2 seconds, scroll the list using P4/P5 until reaching the desired
item and confirm by pressing P6. The following items are available:
• SET OROLOGIO [SET CLOCK] menu
• SET CRONO [SET TIMER] menu
• LINGUA [LANGUAGE] menu
• STATO STUFA [STOVE STATUS] menu
• ORE LAVORO [OPERATING HOURS] menu
• VEDI TARATURE [DISPLAY SETTINGS] menu
• BANCA DATI [DATABASE MENU]
(password-protected)
• AZZERA ORE [RESET HOURS] menu
(password-protected)
• TARATURE FABBRICA [FACTORY SETTINGS] menu (password-protected)
Some menus provide access to user functions, while others are for technicians only and require
the password to be entered.
7.5.1. Clock
To use this function, the power board must be fitted with the optional module. Select the SET
OROLOGIO [SET CLOCK] menu item. Use buttons P6 and P7 to scroll the parameters, and P4
and P5 to change the values. The clock has the following parameters:
Parametro Descrizione
Valori impastabili
UT01
CLOCK DAY
OFF; Day1, ...;Day7
UT02
CLOCK HOUR
from 0 to 23
UT03
CLOCK MINUTES
from 00 to 60
UT01
This parameter is used to set the current day or disable the programming of the timer
thermostat.
Day 1
Monday
Day 2
Tuesday
Day 3
Wednesday
Day 4
Thursday
Day 5
Friday
Day 6
Saturday
Day 7
Sunday
Off
Disabled
UT02
This parameter is used to set the current hour
UT03 This parameter is used to set the current minutes
7.5. Menu functions
To access the menus, hold P4 for 2 seconds, scroll the list using P4/P5 until reaching the desired
item and confirm by pressing P6. The following items are available:
• SET OROLOGIO [SET CLOCK] menu
• SET CRONO [SET TIMER] menu
• LINGUA [LANGUAGE] menu
• STATO STUFA [STOVE STATUS] menu
• ORE LAVORO [OPERATING HOURS] menu
• VEDI TARATURE [DISPLAY SETTINGS] menu
• BANCA DATI [DATABASE MENU]
(password-protected)
• AZZERA ORE [RESET HOURS] menu
(password-protected)
• TARATURE FABBRICA [FACTORY SETTINGS] menu (password-protected)
Some menus provide access to user functions, while others are for technicians only and require
the password to be entered.
7.5.1. Clock
To use this function, the power board must be fitted with the optional module. Select the SET
OROLOGIO [SET CLOCK] menu item. Use buttons P6 and P7 to scroll the parameters, and P4
and P5 to change the values. The clock has the following parameters:
Parameter Description
Possible values
UT01
CLOCK DAY
OFF; Day1, ...;Day7
UT02
CLOCK HOUR
from 0 to 23
UT03
CLOCK MINUTES
from 00 to 60
UT01
This parameter is used to set the current day or disable the programming of the timer
thermostat.
Day 1
Monday
Day 2
Tuesday
Day 3
Wednesday
Day 4
Thursday
Day 5
Friday
Day 6
Saturday
Day 7
Sunday
Off
Disabled
UT02
This parameter is used to set the current hour
UT03 This parameter is used to set the current minutes