1. DL manuals
  2. Faroudja
  3. DVD Player
  4. NRS-DVI
  5. Installation And Operation Manual

Faroudja NRS-DVI Installation And Operation Manual

Manual is about: Native Rate Series

Summary of NRS-DVI

  • Page 1

    Native rate series nrs-dvi digital video processor installation and operations manual ntsc model ™.

  • Page 2: Quick Start

    Quick start instructions the nrs-dvi requires only a few adjustments to be set for proper operation. However, since the processor must be integrated with a display device, and the settings on one will affect the other, careful attention must be made to the settings on both products. Connections read...

  • Page 3

    Quick start ...............................................................................................................................................A installation .....................................................................................................................................

  • Page 4: Installation

    Installation unpacking remove the nrs-dvi unit from the shipping container and examine it for any signs of shipping damage or missing items (check inventory list below). All shipping materials should be saved if the unit is to be moved or returned for service. Shipping unit back to faroudja for serv...

  • Page 5

    Installation 3 5. D15f connector output for use with computer monitors or to a second display device. Use only short cable runs. This output can be used at the same time as the bnc outputs 6. Bnc connectors for main output with rgbhv or yprpb signals to display devices. Cable runs up to 100ft are ok...

  • Page 6: Front Panel Control

    4 front panel control 1. Firmware reset: push a small paper clip into this opening to reset the unit’s cpu. Note: use this reset only if the unit will not respond to commands. It will not erase custom settings. Use the factory restore command in the setup menu to completely reset firmware. See the s...

  • Page 7

    Setup 5 set: screen shape wide screen / 4:3 / wide 4:3 note: this sets the processor for the screen shape of the display to be used. If this is not set properly, the aspect ratio selection for the different sources located in the user menu will be incorrect. • wide screen -choose this when the scree...

  • Page 8: Ir Remote and

    Ir remote and osd operation the nrs-dvi is shipped with an eight button remote for controlling all functions available in the unit. The remote control allows for easy operation by simple navigation through the on screen display (osd) menus. Repeated pressing of a button toggles through the available...

  • Page 9

    The osd consists of four menu tabs: input – picture – display – patterns input menu formats input select: osd video-s-video- rgb-ycrcb note: the pass-thru input cannot be selected from the osd since an osd is not available on that input. Use the input button on the remote to select it. Input select:...

  • Page 10

    Contrast factory 50 note: it is best to set brightness and contrast levels using the controls of the display with the proper test pattern and with the nrs-dvi in the factory default setting for the initial setup. This means with day-to- day use, when the factory preset button is pressed, the system ...

  • Page 11: Available Patterns:

    Operating instructions / rs232 9 bottom blanking this adjusts the bottom edge blanking right blanking adjusts the right edge blanking left blanking adjusts the left edge blanking top blanking adjusts the top edge blanking blanking level this adjusts the blanking from black to white. This can be used...

  • Page 12

    10 rs232 codes following the header, a comma is used to delimit the header from the command. All the commands with their descriptions are listed below. All the text strings are terminated with a carriage return (0x13). Maximum command string length is 250 characters. The header and command are not c...

  • Page 13

    11 rs232 codes g# (0-2) [0=off 1=bi-level 2=tri-level] sync on g/y hp# (0-50) 25 default horizontal position hpol 0=neg 1=pos horizontal sync polarity lb# (0-200) left blanking m# (0-2) [0=rgb, 1=ycrcb, 2=yprpb] output mode osdoff osd off – for processor osdon osd on -for processor outmod 0=analog, ...

  • Page 14

    12 infrared command list ir command list power on/off 0 4:3 (toggle) (aspect ratio) 1 letterbox (aspect ratio) input 2 anamorphic (aspect ratio) aspect ratio 3 power on brightness 4 power off contrast 5 preset 1 color 6 preset 2 tint 7 preset 3 detail 8 preset 4 noise reduction 9 factory function up...

  • Page 15

    13 specifications inputs (interlaced) format ntsc only composite(bnc) 1vpp s-video (4-pin din) 1vpp c -286mvpp component (bnc) auto-detect: y -1vpp(smpte) 480i/480p sent to upconverter, cr -700mvpp 1080i or 720p sent to pass-through. Cb -700mvpp rgb ( bnc) interlaced comp. Sync -1vpp rgb -700mvpp hd...

  • Page 16

    Limited warranty faroudja laboratories, inc. (“faroudja”) warranties that its products will be free of defects in workmanship and material and conform substantially to published specifications under normal use and service. This warranty is made to the first purchaser of the products and extends for ...