Summary of Silver Luna Prestige
Page 1
Titania user’s manual.
Page 2
2 user’s manual safety tips ______________________________ in order to obtain the highest possible sound reproduction quality and for the sake of your own safety, please kindly refer to the following safety guidelines and please adhere to them: • never place the fezz audio titania amplifier near hea...
Page 3
3 table of contents ________________________________________ safety tips ___2___ introduction ___4___ the tube amplifier installation of the device ___5___ unpacking contents of the package description of the elements of the amplifier installation of the vacuum tubes where to place your amplifier in...
Page 4
4 introduction _______________________________________________ thank you for your trust and for choosing the fezz audio titania amplifier. At times when the audio world becomes increasingly digital, fezz audio does not forget about analog lovers. Titania is the polish, series produced integrated vac...
Page 5
5 instalation of the device _______________________________ unpacking please kindly check if the packaging of the titania amplifier has not been damaged during transit. If you find any damages, please immediately contact your dealer. Remove the amplifier and accessories from the packaging. Make sure...
Page 6
6 description of the elements of the amplifier 1) volume control 2) input source selector 3) sockets for the right channel vacuum tubes 4) sockets for the left channel vacuum tubes 5) the housing for the power supply transformer 6) the housing for the output transformers.
Page 7
7 installation of the vacuum tubes place the titania amplifier on a stable surface. Carefully remove the vacuum tubes from their packaging and install them in the appropriate sockets, as shown below, and adhering to the numbering scheme as identified on the packaging. Please pay attention to the dia...
Page 8
8 where to place your amplifier due to the presence of high temperatures during normal operation of the vacuum tubes, the location that you pick to place your amplifier should ensure ample ventilation, a free flow of air. Please maintain at least 10 cm clearance between the housing of the amplifier,...
Page 9
9 interconnections __________________________________________ 1) source signal inputs 2) speaker outputs for the right channel 3) speaker outputs for the left channel 4) socket for the main fuse 5) the iec power supply cord socket 6) mains switch the figure above shows the rear panel view of the fez...
Page 10
10 any and all connections must be made whilst the device is disconnected from the mains power supply. Before making any such connections, make sure that the amplifier is switched off. Hook-up of the power supply cord make sure that the amplifier is switched off. Connect the power cord to the iec so...
Page 11
11 first power-up and getting started ______________________ make sure that all of your wiring is connected in accordance with the information as provided above on page 9 of this manual. Select the source of signal using the rotary selector switch located on the front panel. Set the volume control t...
Page 12
12 adjustment and control of the bias currents _________ setting and control of the bias is a procedure that is required after the first switch-on and after the initial burn-in period of the amplifier. Later on, we recommend to check these parameters once a month. Please make yourself acquainted wit...
Page 13
13 3) measure the actual value of the bias between mr1 and mr2 or mr1 and mr3. 4) adjust the voltage reading using the bias level potentiometer ar1 to a value as close as possible to 500 mv (+/- 20mv). The procedure for adjustment of bias for the left channel similarly as described in the procedure ...
Page 14
14 “burning-in” of the amplifier _____________________________ any tube amplifier requires an initial pre-heating (or "burn-in") period, in order so that it achieves its full sonic potential. This is due to the presence of residual polarization of dielectric elements and due to a necessary stabiliza...
Page 15
15 technical data _____________________________________________ type: stereo integrated power amplifier model: titania output power: 2x 45w circuit architecture push-pull, class ab1 output impedance: 4Ω / 8Ω input connectors: 3x rca thd distortion: frequency response: 18hz – 103khz (at -3db) power c...
Page 16
16 limited warranty conditions _____________________________ the manufacturer, the company fezz audio warrants that this titania amplifier is free from defects in materials and in workmanship. This warranty is valid for a period of 24 months from the date of purchase. During the warranty period, any...