1. DL manuals
  2. G-Force
  3. Battery Charger
  4. G6
  5. Instruction Manual

G-Force G6 Instruction Manual

Manual is about: DC BALANCE CHARGER & DISCHARGER

Summary of G6

  • Page 1

    Charger dc balance charger & discharger ver.1.30 instruction manual products by g-force, inc. Www.Gforce-hobby.Jp mare-kanda bld.9f, 1-3-1, kajicho, chiyoda-ku, tokyo, 101-0044, japan copyright © 2014 g force, inc. All right reserved..

  • Page 2

    Table of contents introduction 01 congratulations on your choice of the g-force g6 balance charger/ discharger. The unit is simple to use, but the operation of a sophisticated automatic charger such as g-force g6 balance charger/discharger does require some knowledge on the part of the user. These o...

  • Page 3

    02 introduction 03 please read this entire operating manual completely and attentively before using this product, as it covers a wide range of information on operating and safety. Or please do use this product in company with a specialist! Special features optimized operating software features the s...

  • Page 4

    04 special features 05 cyclic charging/discharging 1 to 3 cyclic and continuous process of charge>discharge or discharge > charge is operable for battery refreshing and balancing to stimulate the battery's activity. Data store/load the charger can store up to 10 different charge/discharge profiles f...

  • Page 5

    06 warning and safety notes 07 these warnings and safety notes are particularly important. Please follow the instructions for maximum safety; otherwise the charger and the battery can be damaged or at worst it can cause a fire. The allowable dc input voltage is 11-18v dc. Never leave the charger una...

  • Page 6

    08 09 charging during charge process, a specific quantity of electrical energy is fed into the battery. The charge quantity is calculated by multiplying charge current by charge time. The maximum permissible charge current varies depending on the battery type or its performance, and can be found in ...

  • Page 7

    10 11 lithium battery connection diagram co nnecting the battery important!!! Before connecting a battery it is absolutely essential to check one last time that you have set the parameters correctly. If the settings are incorrect, the battery may be damaged, and could even burst into flames or explo...

  • Page 8

    Program flow chart program flow chart 12 13 program select ba tt memor y enter st ar t ba tt memor y [1] enter set enter st ar t ba tt type lipo ba tt vol ts 7.4v ( 2s ) charge current 4.9a dsch current 2.2a dsch vol tage 3.0v/cell tvc=your risk 4.20v enter st ar t enter st ar t program select syste...

  • Page 9

    14 15 lithium battery(lipo/life/liion)program these programs are only suitable for charging and discharging lithium batteries with a nominal voltage of 3.3v, 3.6v and 3.7v per cell. These batteries need to adopt different charge technique is termed a constant voltage(cv) and constant current(cc) met...

  • Page 10

    16 17 lithium battery(lipo/life/liion)program charged capacity number of cells charging time charging current battery voltage screen. If both numbers are identical you can start charging by press start/enter button. If not, press batt type/stop button to go back to previous screen to carefully check...

  • Page 11

    18 19 lithium battery(lipo/life/liion)program number of cells elapsed time charge or discharge current supplied capacity current voltage battery this screen shows the real-time status charging. Press batt type/stop key once to stop the charge process. Discharging lithium battery number of cells elap...

  • Page 12

    20 21 n i m h 2 . 0 a 9 . 5 2 v a u t 0 0 0 : 1 3 0 0 0 0 0 charging / battery in re-peak charge mode nimh nicd re-peak charge mode (nicd and nimh batteries only): in re-peak charge mode, the charger can peak charge the battery once, twice or three times in a row automatically. This is good for conf...

  • Page 13

    22 23 pb( lead-sulphuric acid) battery program this is programmed for charging pb(lead-sulphuric acid) battery with nominal voltage from 2 to 20v. Pb batteries are totally different from nicd or nimh batteries. They can only deliver relatievely lower current compare to their capacity, and similar re...

  • Page 14

    24 25 battery memory set the charger can store up to 10 different charge/discharge profiles for your convenience, and the stored profiles can be recalled quickly without having to go through the setup process. Batt memory 【1】 enter set batt type lipo enter the battery memory program, you can change ...

  • Page 15

    26 27 lithium battery meter program select li batt meter press the start/enter button to enter the lithium battery meter. 4.19 4.15 4.18v 0.00 0.00 0.00v the screen indicate each cell's voltage. Main 12.52v h4.190v l4.160v the screen indicate the total voltage, the highest voltage, the lowest voltag...

  • Page 16

    28 29 capacity cut-off on 5000mah key beep on buzzer on capacity current safety time 2000mah 2.0a (2000/2.0=1000)/11.9=84 minutes 3300mah 3.0a (3300/3.0=1100)/11.9=92 minutes 1000mah 1.2a (1000/1.2=833)/11.9=70 minutes for example: this program sets the maximum charge capacity that will be supplied ...

  • Page 17

    30 31 it incorporates a variety of functions for the systems to verify processes and the state of the electronics. In case of an error the screen will display the cause of error and emit an audible sound. Incorrect polarity connected. The battery is interrupted. Connect error check main port the bat...

  • Page 18

    32 this charger is designed and approved exclusively for use with the types of battery stated in these instruction manual. G-force accepts no liablility of any kind if the charger is used for any purpose other than that stated. We are unable to ensure that you follow the instructions supplied with t...