GOLDEN STATE INSTRUMENT CO GS-16CH264 User Manual

Manual is about: 16, 8, 4 CHANNEL H.264 DIGITAL VIDEO RECORDER

Summary of GS-16CH264

  • Page 1

    1 l gs-16ch264 gs-8ch264 gs-4ch264 16, 8, 4 channel h.264 digital video recorder ─ user manual gs-4/8/16ch264 rev 3 ver 1.0 this document contains preliminary information and subject to change without notice. 2 this symbol is intended to alert the user to the presence of unprotected “dangerous volta...

  • Page 2

    3 table of contents chapter 1 main menu setup ____________________________________4 1-1 record setup ____________________________________________ 5 1-1.1 quality & frame rate setup _____________________________6 1-2 event setup ______________________________________________ 6 1-2.1 motion setup ____...

  • Page 3

    5 table 1-0.2 the operation of remote control under the setting menu item description switch to different options under one item switch to different items menu save setup and back to live mode esc back to upper level of menu without saving enter enter the menu, or display virtual keyboard ps. The in...

  • Page 4

    7 1-2.1 motion setup item description alarm duration(seconds) when motion detect,the number of seconds continuous alarm 1~16 you can setup independently for each channel. Enable check the box to enable/disable motion detection for each channel. Sensitivity drag the white bar or press ◀ ▶ to set up s...

  • Page 5

    9 1-3 schedule setup except from starting recording manually, you can also setup the recording time by weeks and schedule including normal, motion detect, and recording type. Item description page each page provides 10 schedules for setup. 5 pages in total. Holiday setup enter to setup holiday, up t...

  • Page 6

    11 1-5 account setup the account setup menu is used to provide role-based permission independently setting for each user (maximum of 4 users) to access dvr over network. The default admin account and password is “admin” and“123456” (the default password remains the same after firmware upgrade) item ...

  • Page 7

    13 1-6.1 networking setup there are three ways to connect to the network as followed. 1-6.1.1 dhcp when dhcp is selected, ip address will be assigned by dhcp server automatically. 1-6.1.2 lan select lan to manually input the network settings item description ip address enter ip address provided by i...

  • Page 8

    15 item description enable enable advance setting user name enter isp username password enter isp password ip address enter the isp provides a fixed ip address。 (if the client uses the internet only need to enter a fixed ip) ps:this feature currently only supports the huawei 3g card 1-6.2 http setup...

  • Page 9

    17 1-6.4 mail setup when an event occurs (vloss, motion), an email will be sent to the receiver’s account automatically. If you select motion, you will be emailed a snapshot of the event. Item description enable e-mail notification check the box to enable/disable e-mail notification function. Smtp s...

  • Page 10

    19 1-8 system setup item description dvr name the name of dvr will be shown when users login from remote access. Dvr location the location of dvr will be shown when users login from remote access language click or press ▼ to select osd language. Remote id default id is 0. Dvr is controlled by standa...

  • Page 11

    21 1-8.2.1 change date & time setup date and time of dvr manually according to user’s local time. 1-8.2.2 time zone and daylight saving time setup set up time zone and activate daylight saving time function according to user’s dvr location. Item description select time zone enter to modify gmt from ...

  • Page 12

    23 item description key tone enable/disable audible button presses for remote and panel buzzer enable/disable buzzer operation when the alarm is triggered for sensor, motion and vloss (video loss). Relay enable/disable the signal to be sent to the relay out blocks when the alarm is triggered for sen...

  • Page 13

    25 1-10 diagnostic item description version the current firmware version of dvr ip the connected ip address of dvr. If disconnected from network, the screen will display ” network disconnect”. Mac mac address of dvr no. Hdd number volume hdd capacity used rate percentage of space used on hdd. Status...

  • Page 14

    27 ifileplay instructions step 1: install 「ifileplay」software to your pc. You can get「ifileplay」file from the cd with dvr contents ps: when you using usb to backup file, ifileplay.Exe will copy to usb with the backup file automatically. Step 2:run「ifileplaypack.Exe」 。 step 3:click「open」 ,select the ...

  • Page 15

    29 2-2 search setup item description event search event search menu time search enter time search menu 2-2.1 event search the dvr automatically records events with type, time and channel information included. If there is recording data for an event, a yellow signal will be shown on the left side of ...

  • Page 16

    31 2-2.2 time search time search can search for the specific time of recording data to playback. Press “enter” or left click on the desired date to playback. Note that dates with recording data are marked with a red square “ □ “system will start playing back according to the date you selected. Calen...

  • Page 17

    33 step four: run or save our remote software. Step five: if you choose to run the software, start window will be shown up. Please enter information of login dvr: ip, port, username and password, or choose “play recorded file” to open backup files in your pc. Step six: you’ve logged into the dvr 34 ...

  • Page 18

    35 step four: dvr images appear. 3-3 how to do remote monitoring through jpeg viewer(only monitor fun ction) step one:enter the ip address of dvr in ie browser. The address appeared in this image is only for demonstration. Actual address is depending on the setup of on-site dvr. Step two: windows as...

  • Page 19

    37 3-4 remote software operation open the file “dvremotedesktop.Exe”; enter the information of dvr “ip address”, “port” “username” and “password” and click “ok”. You should be able to login dvr successfully and start to use the software. The default username and password is 「admin/ 123456」 “dvremote...