1. DL manuals
  2. I-Sotec
  3. Amplifier
  4. Auxgate Connect
  5. Manual manual

I-Sotec Auxgate Connect Manual manual

Manual is about: Car-Audio-Amplifiers and Multimedia Extensions

Summary of Auxgate Connect

  • Page 1

    I-soamp / auxgate car-audio-amplifiers and multimedia extensions by intelligent solutions and technologies germany manual.

  • Page 2

    I-soamp medialink, i-soamp-4cx und auxgate® connect wir beglückwünschen sie zum kauf dieses i-sotec produktes und danken für ihr vertrauen! Mit diesem car-audio-gerät haben sie ein technologisch aus- gereiftes und innovatives produkt erworben, das ihnen viele jahre hervorra- genden musikgenuss ermög...

  • Page 3

    A installation when installing the equipment, be sure that it is well ventilated. It must not be covered or mounted near heat emitting objects or be subjected to direct sunlight. The i-soamp medialink can heat itself up significantly (up to 80°c); it is therefore important to ensure sufficient clear...

  • Page 4

    A.1.1: situation as is: remove the original radio from the radio slot according to the vehicle manufacturer's instructions so that you can get to the terminals on the rear side of the radio. If your original radio has an iso terminal – possibly next to other ter- minals such as the antenna cable - y...

  • Page 5

    A.1.2 overview – the i-soamp connection principle this depiction is designed to give you an overview of how the i- soamp is connected to your vehicle's components in principle. The following steps are required to connect the i-soamp to your existing car radio: 1. Connect the i-soamp cable harness to...

  • Page 6

    A.1.4 front + subwoofer (i-soamp only) with this connection, the front speakers and the optional subwoofer are driven by the i-soamp. The back speakers can be connected directly to the radio by by switching the 4-pinned plugs (see picture). Do only use i-sotec subwoofers! Other speakers can damage t...

  • Page 7

    Cable harness iso loudspeaker plug from the car radio and connect the it to the iso loudspeaker recaptacle (brown) of the i-soamp’s cable harness. 2. Disconnect the 4-pinned plugs and connect them as seen in the pic- ture. This way the 4-pinned plugs on the iso loudspeaker socket and on the iso loud...

  • Page 8

    A.1.6 connection to the power supply the i-soamp and auxgate are supplied with an iso power adapter as standard equipment. The power adapter is connected between the car radio and the vehicle cable harness. 1. Remove the vehicle cable harness iso power plug from the car radio and con- nect it to the...

  • Page 9

    This is the case and that you have not selected a piece of metal that was only glued to the vehicle chassis. The black cable is connected to the grounding point; make sure there is a good electrical contact. 3. The red cable is connected to the positive terminal of the battery via a suitable fuse. C...

  • Page 10

    Liability exclusion: i-sotec assumes no liability for damage that is caused by improper use of the device, improper installation or incorrect connections or non-observance of the handling instructions described in these opera- ting instructions. The device may only be operated with original i-sotec ...

  • Page 11

    B user’s guide i-soamp-4cx b.1. Operating the equipment for the first time 1. Turn on the radio with the volume set at low. 2. After checking the operation of the individual loudspeakers, set the volume of the radio a little higher. If appropriate, now use the level adjuster of the power amplifier t...

  • Page 12

    C user’s guide i-soamp medialink c.1 operating elements and connections c.1.1controller a. Volume control for input aux 1 b. Volume control for input aux 2, tel, nav c. Switch for mode aux 2 d. Function indicator aux 1 e. Function indicator i-soamp medialink f. Function indicator aux 2 in nav mode g...

  • Page 13

    C.2 installation and start-up 1. Connect the i-soamp medialink as described in the appendix a1 to the radio, speakers and power. 2. Connect the provided controller to the i-soamp medialink (see chapter c.2). 3. Connect the external sources e.G. Mp-3 player, navigation and telephone to the aux inputs...

  • Page 14

    Scom which provides a fully automatic muting for the different sources while traffic- and/or navigation-announcements or a phone-call are made. The automatic muting system can be activat- ed when pushing the button c. C.3.5.1 mode aux after start-up the mode aux is activated for the input aux 2 so t...

  • Page 15

    D operation and connection of the auxgate connect d.1 connection the connection of the auxgate connect to power supply and speakers is to be done as described in chapter a1 (the only option for speaker connection is “normal”). The use with a subwoofer is not intended. All aux sources are connected d...

  • Page 16

    D.4 settings the main volume of the 3 function modes(radio, aux 1, nav/tel) is to be set by the level-controls “level”, “aux 1” and “nav/tel” at the auxgate connect housing. These controls are usually set to 0 when leaving the factory if not then please correct the settings. Settings for “level”: se...